Advertisement
22
II
I Jill
I
......
:
J,T,,I,I T
G. TROUBLE
SHOOTING
CHAKT
SYMPTOM
CAUSE
,,,,,,,,,,,,,,,,,,,,,,
............
_._
_ts_
]. Fueltar_empty
• or will ran oaly for
2. Engi_flooded.
"afew seconds atter
3. Spark plug not faing.
starting
4. Fadnotreachinge.a_t_tor.
Eagiae will not idle
properly
2,
2.
power,or dies
3.
.undera load
4.
F.agia¢ will not
accelerate, lacks
Enginesmokes
excessively
Engine rims hot
IIIIIIIIIIIIIIIIIIIII
II
III
III
/IWIIII .
5. Cartmrgtor _adjusm_nt.
None ofthe above,
'
:-. :
,,,,,,,,,,,,,,,,,
,,
,. i i i
1. Idle speed set too fast or too slow.
2. Low speed mixturere, quires adjusm,.ent.
2.
3. Throttle triggersct=w too fight.
3.
4. N'o_ ofthe ahoy.
4.
I
_1111
loll
IIIII
I
IIII
HIIIIH
III
II
I
Air m_r_y.
Sparkplug fouled.
Carburetorrequires a djustmeta.
Muffler outletsplugged.
5. None of the above.
1, Air filter dirty.
I.
2. Fuel mL_reincorrect.
2.
L Fuel mixturein_rrect_
I.
2. Highs_
mixtu_set too low(lean),
2,
3. Sparkplug i ncorre_,
3.
I
I
II
I
I
II1 IlJll II 11
_
_
...............
4.
Trimmer head mms
I.
atidlespeed
2.
3.
Trimmer5¢ad
1.
stops _ a
Ioador
2.
I does not turnwhen
3.
engine isaccelerat_l
T
does not advance
1.
or bnml:swhile cutting
2.
3.
4.
-i,
i
Line w_lds on spool
2.
3.
4.
Li__releasescontinuousiy
L
2.
3.
4.
Lineusage is excessive
L
3.
,4.
Line pulls back into head
1.
.... _'="lllllllll
, l
REMEDY
1. FOl tankwith correct furl mixture,
2. See "StartingImmzctions:'
3. Install new plug/check igaidon system.
4. Clean fuel filter; inspectfuelline.
5. See "CarburetorAdjus_ats:'
6. Contact y ourSears$erv_ C_nter.
t. ,See "Carburetor Adjustments."
See "Carbur_or Adjustmcats:'
Loosen screw tofr_tngge¢,
Coatact your se_
service Ce,ntes-
.....
•
Illllll'llll
..................
I.
2.
3.
4.
5.
Clean orreplace airfilter,
Clean or replace sparkplugand r_gap,
See "Carburetor AdjustmeatsY
ContactyourSears ServiceCenter.
Contactyour SearsServiceCcat_r.
Clean or replace air filter.
Refud with correct
fuel m ixture.
See "CarburetorA@hqments :"
See "Fueling Yo_ Unit:'
See "Carburetor AdjmunentsY
Replace with correct plug.
None of the above.
Carbaretor requitesadjustment.
Thr_e trigs.e:screwtoo fight.
au_ _,-_ repair.
r
Drive shaft broken or not engaged.
Carburaor require_djustments.
_utch nglui_ repah-.
:
i i ml
rl
Line improperlyrouted in lIead.
Line improperly wound onto spool.
Line size incorrect.
Too little line outside head.
, Illlllllll
'qWIJllm
Illlll
I
1: Line s'o__ incorrect.
4. C0ntactyour Sears Service Center. _
;
I. See "Cadmretor AdjusanentsY
2. Loose.n screw to free trigger.
3. Contact your Sears Service Center.
1. P,_ace or see '_tssembly:'
2. See "Carburelvr Adjus_entsY
3. Contact your Sears Service Center.
I. Remove cover.Check line muting.
2. Rewindline t ightly
andevenly. ®
3. Useonly.080"SearsLasetIAne
•
4. Remove cover. Pall 6" oftine tooutsid_.
1.
Useoniy .080" Sears l.aser IAne®. "
Incorrect spool.
2. Use properspool.
Crowdinglineagainst material being cut:
3. Cut withtipofline.
Cutting at higher speed than necessary.
4. _Reducecutting sp_..,.,
Line wound beyond notches on spool.
1. Rewind line tightly and evenly,
Line improperly roul_ hi head,
2. Remo_ cover. Check line muting.
Line size incorrect.
3. Use only J380;" Sears laser Linee.
Shield
ill.lied.imProperly.
4.
Reinstall shield properly.
Lineimproperly muted in head.
1.
Linesize incorrect.
2.
Cutting athigh speed around hard objects.
3.
Crowding line against _
being cut.
4.
Too little line outside of head
Remove cover. Check line muting.
Use only .080" Sears LaserLine®.
Redt_ spe_ aroundhardobjects.
Cutwith tip ofline.
R_ov¢ cover. Pall 6 " of line _ oatsk_.
Advertisement
