Subscribe to Our Youtube Channel
Summary of Contents for Xantrex GT Series Three Phase Ethernet Communications Kit
- Page 1 Installation Guide GT Series Three Phase Ethernet Communications This guide for use by qualified personnel only...
- Page 3 GT Series Three Phase Ethernet Communications Kit Installation Guide This guide for use by qualified personnel only...
- Page 4 About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products ranging from small mobile units to utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup power applications in both grid-connected and stand-alone systems. Xantrex products include inverters, battery chargers, programmable power supplies, and variable speed drives that convert, supply, control, clean, and distribute electrical power.
-
Page 5: About This Guide
About This Guide Purpose The purpose of this Installation Guide is to provide explanations and procedures for installing and configuring the GT Series Three Phase Ethernet Communications Kit. Scope The Guide provides safety guidelines, procedures for installing the GT Series Three Phase Ethernet Communications Kit, as well as information about configuring the Ethernet Communications Kit protocol for proper operation. -
Page 6: Conventions Used
These notes describe things which are important for you to know, but not as serious as a caution or warning. Related Information You can find more information about Xantrex Technology Inc. as well as its products and services at www.xantrex.com 153553... -
Page 7: Important Safety Instructions
Important Safety Instructions SAVE THESE INSTRUCTIONS - DO NOT DISCARD This manual contains important safety instructions for the GT Series Three Phase Ethernet Communications Kit that must be followed during installation and maintenance procedures. WARNING: Shock Hazard Read and keep this Installation Guide for future reference. Before operating and maintaining the Ethernet Communications Kit, read all instructions, cautionary markings, and all other appropriate sections of this manual. - Page 8 Safety Risks WARNING: Shock hazard Parts of the capacitor charge will still be energized for a maximum of five minutes after being disconnected. Open doors only after the device is disconnected and discharged. Check whether the device is no longer live (DC voltage) including terminals TB3 and TB4. WARNING: Amputation hazard The inverters contain integrated ventilators including rotating ventilator wheels.
-
Page 9: General Safety Precautions
Safety General Safety Precautions 1. When installing the Ethernet Communications Kit in GT Series Three Phase Grid Tie Inverters use only components recommended or sold by Xantrex. Doing otherwise may result in a risk of fire, electric shock, injury to persons, and will void the warranty. 2. - Page 10 Safety Operational Safety Procedures Never work alone when servicing this equipment. A team of two is required until the equipment is properly de-energized, locked-out and tagged, and verified de-energized with a meter. Thoroughly inspect the equipment prior to energizing. Verify that no tools or equipment have inadvertently been left behind.
- Page 11 Safety 4. Open, lockout, and tag the DC Disconnect Switch (S1) on the right door of the Inverter enclosure. See GT100 or GT250 Grid Tie Inverter manual for the location of the DC Disconnect Switch. CAUTION Once the DC Disconnect Switch is open, there will be DC voltage on the PV Array side of the switch where TB3, TB4, and TB5(PV GND) are located.
-
Page 12: Intended Use
Safety De-Energize/Isolation Procedure The following procedure should be followed to de-energize the Inverter for maintenance. WARNING The terminals of the DC input may be energized if the PV arrays are energized. In addition, allow five minutes for all capacitors within the main Enclosure to discharge after disconnecting the Inverter from AC and DC sources. -
Page 13: Table Of Contents
Contents Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -v Installation and Configuration Description of the GT Series Three Phase Ethernet Communications Kit - - - - - - - - - -1 Interface Requirements - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1 Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2... -
Page 15: Installation And Configuration
Installation and Configuration Description of the GT Series Three Phase Ethernet Communications Kit The GT Series Three Phase Ethernet Communications Kit is an option for the GT Series Three Phase Grid Tie Inverters. The Ethernet Communications Kit is an option that is available for remote plant monitoring. -
Page 16: Installation
Installation and Configuration Installation WARNING: Shock hazard Safety requirements mandate that this equipment not be serviced while energized. Power sources for the inverter must be locked-out and tagged (see “De-Energize/Isolation Procedure (Shutdown)”) prior to servicing. A padlock and tag should be installed on each energy source prior to servicing. -
Page 17: Installing The Ethernet Communications Kit
Installation Installing the Ethernet Communications Kit You will have to make connections to the CCU control board inside of the enclosure. Use caution not to discharge any static electricity onto the control board. Use the following procedure to install the new Ethernet Communications Kit: 1. - Page 18 Installation and Configuration Fiber Optic RS232/Fiber Cable Adaptor Power Power Connector Supply Cable Ethernet Surge Protector Ethernet Cable Figure 2 Ethernet Kit Cable Connections 5. Connect the Ethernet cable from the computer network to the unprotected connection on the Ethernet surge protector. 6.
-
Page 19: Energize Procedure (Startup)
Configuring Energize Procedure (Startup) Use the following procedure to turn on the Inverter: 1. Remove any lockout devices from the utility connection circuit breaker and PV disconnect switch. 2. Close the utility connection circuit breaker. 3. Close the AC disconnect. 4. -
Page 20: Configuring The Lan Interface
Installation and Configuration Figure 4 Ethernet Communications Kit Configuration Diagram Configuring the LAN Interface To configure the Ethernet Communications Kit (NPort Express) follow the instructions provided on the NPort Installation CD. 153553 For use by qualified technicians only... -
Page 21: Warranty And Return Information
What does this warranty cover and how long does it last? This Limited Warranty is provided by Xantrex Technology Inc. ("Xantrex") and covers defects in workmanship and materials in your GT Series Three Phase Ethernet Communications Kit. This Warranty Period lasts for five (5) years from the date of purchase at the point of sale to you, the original end user customer, unless otherwise agreed in writing. - Page 22 Warranty and Return Proof of purchase may be in any one of the following forms: • The dated purchase receipt from the original purchase of the product at point of sale to the end user; or • The dated dealer invoice or purchase receipt showing original equipment manufacturer (OEM) status;...
-
Page 23: Return Procedure
Include the following: • The RMA number supplied by Xantrex Technology Inc. clearly marked on the outside of the box. • A return address where the unit can be shipped. Post office boxes are not acceptable. -
Page 24: Out Of Warranty Service
Warranty and Return If you are returning a product from outside of the USA or Canada In addition to the above, you MUST include return freight funds and are fully responsible for all documents, duties, tariffs, and deposits. If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex return material authorization (RMA) number is not required. - Page 26 Xantrex Technology Inc. 1 800 670 0707 Tel toll free NA 1 408 987 6030 (direct) 1 800 994 7828 Fax toll free NA customerservice@xantrex.com www.xantrex.com 153553 Revision A Printed in USA...
Need help?
Do you have a question about the GT Series Three Phase Ethernet Communications Kit and is the answer not in the manual?
Questions and answers