Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Intergraph ErgoAct OEM Monitor
- Page 1 ErgoAct OEM Monitor Installation Guide February 1997 DHAF00720...
- Page 2 The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of the license. No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies.
-
Page 3: Table Of Contents
Contents Installing an OEM Monitor..................1 Remove the Existing Monitor and Separator Plate ............1 Set Up the Panasonic OEM Monitor ................1 Preparing the Monitor for Installation..............2 Attaching the Separator Plate................5 Set Up the Hitachi OEM Monitor ..................9 Removing the Swivel Base................9 Attaching the Adapter Bracket.................9 Attaching the Separator Plate................. -
Page 5: Installing An Oem Monitor
Installing an OEM Monitor This document explains how to remove existing monitors from the ErgoAct workstation stand, and to install a Panasonic or Hitachi OEM monitor onto the workstation stand. Read the instructions in this document before proceeding with the installation. To perform the installation, you will need the following tools: No. -
Page 6: Preparing The Monitor For Installation
Preparing the Monitor for Installation WARNING The monitor is heavy and could cause serious personal injury if dropped. Two persons are required to lift and carry the monitor. 1. Unpack the monitor from its shipping carton. 2. Verify that the monitor power cord is supplied. 3. - Page 7 5. Firmly press down and pull out the press tabs on the swivel base as shown in the following figure. Press Tabs Swivel Base 6. Remove the swivel base from the monitor by sliding it to the back of the monitor.
- Page 8 7. Place the adapter bracket onto the bottom of monitor. Ensure the holding latches are secured inside the slots in the monitor frame. Refer to the following figure. Adapter Bracket Slot 8. Slide the bracket toward the front of the monitor to secure it in place. The bracket snaps in without using screws.
-
Page 9: Attaching The Separator Plate
Attaching the Separator Plate The adapter plate is designed with mounting holes so that it can be used in single-monitor and dual- monitor configurations. These holes are used to properly align the separator plate (CFAB532E) to the adapter bracket. After the separator plate is installed, the monitor is set onto the workstation stand. - Page 10 Single-Monitor Configuration 1. Install the four shoulder screws through the separator plate into the adapter bracket according to the locations shown in the following figure. Separator Plate Adapter Bracket 2. Go to “Install the OEM Monitor” to complete the monitor installation. Use the screws removed in “Remove the Existing Monitor and Separator Plate”...
- Page 11 Dual-Monitor Configuration The left-right orientation used in the following directions assume you are facing the front of the workstation stand. 1. For the monitor to be installed on the right side of the workstation stand, install the four shoulder screws through the separator plate into the adapter bracket according to the locations shown. R = Holes for Right Monitor Separator...
- Page 12 2. For the monitor to be installed on the left side of the workstation stand, install the four shoulder screws through the separator plate into the adapter bracket according to the locations shown. L = Holes for Left Monitor Separator Plate Adapter Bracket...
-
Page 13: Set Up The Hitachi Oem Monitor
Set Up the Hitachi OEM Monitor The hardware kit used to install the Hitachi monitor onto an ErgoAct stand contains the following items (not including packaging and documentation): One monitor adapter bracket (CFAB334) Four shoulder screws (CFAB507) Two M6x12mm Phillips screws (CPHM044) Three M4x8mm Phillips screws (CPMH022) Removing the Swivel Base WARNING... -
Page 14: Attaching The Separator Plate
Screws (2) Adapter Bracket Holding Latch Repeat these steps for the second monitor, if applicable. Attaching the Separator Plate The following figure shows the mounting hole pattern for the adapter bracket. These holes are used to properly align the separator plate to the adapter bracket. Shoulder screws (included with the OEM monitor kit) attach the separator plate to the bottom of the monitor. - Page 15 2. For a single-monitor configuration, secure the separator plate to the adapter bracket. Install the four shoulder screws into locations shown in the following figure. Separator Plate Shoulder Screws (4) 3. For the left monitor of a dual-monitor configuration, secure the separator plate to the adapter bracket.
- Page 16 4. For the right monitor of a dual-monitor configuration, secure the separator plate to the adapter bracket. Install the four shoulder screws into locations shown in the following figure. Separator Plate Shoulder Screws (4) Refer to “Install the OEM Monitor” to install the monitor.
-
Page 17: Install The Oem Monitor
Install the OEM Monitor 1. Place the monitor onto the platform of the ErgoAct stand, setting the shoulder screws inside the keyholes on the platform. Slide the monitor so the shoulder screws lock in the keyholes. Keyholes Screws (2) 2. Thread the screws through the separator plate into the mounting holes. Alternately turn each screw about two turns until the monitor is securely fastened to the stand.