IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 6
Design Alteration Warning - Do not alter or add Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related characteristics which are often not evident from receiver. Design alterations and additions, including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
Page 7
Precautions during Servicing A. Parts identified by the _ symbol are critical for When connecting or disconnecting the internal safety. connectors, first, disconnect the AC plug from the Replace only with part number specified. AC supply outlet. B. In addition to safety, other parts and assemblies M.
Page 8
Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Bottom View Top View Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds).
Page 10
The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
With Iron Wire: Installation Using desoldering braid, remove the solder from Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 12
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M_-_) t hat is properly grounded to remove any static electricity that may be charged on the body.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal This flowchart indicates the disassembly steps for the Step/ RemovePUnhook/ Part Unlock/Release/ cabinet parts, and the CBA in order to gain access to Loc. Fig. Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
Page 15
[14] Front Cabinet (s-s) [4] Function [12] Junction-B (s-5) Speaker ..[10] LCD Module Holder Desolder [13] Speaker [6] IR Sensor [9] Main CBA [7] Jack (s4o) Holder !/ // [13] Speaker (S-11) Speaker Holder Module PCB [11] Holder (s-6) (sqo) (s-9) [5] Tilt Stand Holder...
Page 16
TV Cable Wiring Diagram Function o LCD Module Main CBA I°"'°7 CN1202 CN1201 CN1301 E] CN401 _--- F1 CN402 Module F] CN403 Junction=A CN62 CN61 CL801 CN801 CN802 r- -_CN1302 Junction=B_.) CN102 CL 1104 To Speaker DTV Module CBA Unit IR Sensor Fig.
Page 17
ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: "CBA" is abbreviation How to set up the service mode: "Circuit Board Assembly." Service mode: Note: Electrical adjustments are required after Use the service remote control unit. replacing circuit components and certain mechanical parts. It is important to perform Turn the power on.
The following adjustment normally are not Button Data attempted in the field. Only when replacing the Item (on the service Value LCD Panel then adjust as a preparation. remote control) D2-BRT 2. White Balance Adjustment D2-CNT Purpose: To mix red, green and blue beams correctly D2-CLR-R for pure white.
Page 19
arenotwithinspecification, adjust"DB(C/D1)" o r [VIDE02] "DR(C/D1)". R efer t o "1.Initial S etting." Press [SETUP] button on the service remote [RF/VIDEO1 ]----(APE 20%) control unit and press [3] on the service remote Press [3]button toselect " COB(C/D1 )" forBlue control (selecting "C-BRT" mode). adjustment.
HOW TO INITIALIZE THE LCD TELEVISION How to initialize the LCD television: Turn the power on. (Use main power on the TV unit.) To enter the service mode, press the service button on the service remote control unit. (Refer to page 5-1 .) - To cancel the service mode, press [POWER] button on the remote control.
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS Standard Notes Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements;...
Page 29
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE A, VFUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE Me:ME TYPE DE A, V. 2.
Page 30
Main 1/5 Schematic Diagram VOLTAGE CHART CN1201 Voltage L¸ i '{;ON i ]Nul _AiF 2/5 / ,_i _ / o; d4,_TF 3/5 / __ii i7_7_7_ ..7_i : _ !CONT =k_,AiN4/5 / _--"_' i i _ .._ _ ..EVEN ....
Page 34
Main 5/5 Schematic Diagram CAUTION NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit• If Main Fuse (F601) is blown, check to see that all components in the power supply The voltage for parts in hot circuit is measured using replace only with same type 4 A, 125V fuse.
Page 35
Function Schematic Diagram RiiOi IVOL DOWN] IINPUT SELECT] swllo_ sw!t02 swil03 swll04 swi!05 swtt07 TO MAIN CBA) CNi30i KEY-IN-2 KEY-IN-! AL+3,3V(D) SW!I_t nito9 UNLESS OTHER!4ISE SPECIFIEB= SWITCHES ARE SKQSAB, A7140SCF...
Page 36
IR Sensor Schematic Diagram SENSOR KSM-602SR2E-2 (RENOTE SENSOR) TO MAIN CBA) CLtI04 Rl143 CN1302 AL+3.3V(D) _Ct142 '2.2/50V REMOTE A7140SCI R...
Page 37
DTV Module 1/2 Schematic Diagram Fh_{ q k L ;k L 8-10 A7140SCD1...
Page 39
Main CBA Top View CAUTION Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. protection against fire, Also, in order to have the ability to increase the input If Main Fuse (F601) is blown, check to see that all components...
Page 40
Main CBA Bottom View CAUTION Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input If Main Fuse (F601) is blown,...
Page 41
IR Sensor CBA IR Sensor Function CBA Top View Bottom View Top View BA7120F01021-2 Junction-A CBA Top & Bottom View Function CBA Bottom View BA7120F01021-3 Junction-B CBA Top & Bottom View BA7120F01021-1 BA7120F01021-4 8-14...
WAVEFORMS WF1~WF7 Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram,) input: NTSC Color Bar Signal (with lkHz Audio Signal) Pin 71 of tC1202 Pin 56 of IC1202 Pin 76 of tC1202 Pin 66 of tC1202 Pin 57 of IC1202 Pin 14 of IC801 Pin 75 of IC1202 LC5WF...
IC PIN FUNCTION DESCRIPTIONS IC1202 (LCD Drive / LCD Signal Signal Name Function Process / TV Micro Controller) XOUT Crystal Oscillation Output (27MHz) Signal Name Function VDD+3.3V +3.3V VDD 40 VSS VDD+3.3V +3.3V VDD 41 VSS KEY-IN-1 Key Input 1 42 VDD+3.3V +3.3V VDD KEY-IN-2...
Page 45
Signal Name Function Signal Name Function 119 VSS S-VIDEO-Y Luminance Signal Input AVDDA +3.3V VDD 120 VSS 121 VSS VDD+3.3V +3.3V VDD 122 LPF Panel Clock PLL Filter 123 RSPI Reference Terminal 124 NU Not Used VDD+3.3V +3.3V VDD 125 CLKL Clock Signal Output VDD+3.3V +3.3V VDD...
EXPLODED VIEWS Cabinet SP802 B14 ... -A10 iJunction-B CBA :: " iIR Sensor CBA:: SP801_-O_ LCD1 ..". See Electrical Parts List for parts with this mark. 12-1 A71 40CEX...
Page 47
Packing Some Ref. Numbers not in sequence. Packing Tape Tape Packing Ta_,.././././ ./" Packing Tape \ Packing Tape 12-2 A7140PEX...
MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a ,_ have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. ,_ have special characteristics important to safety. CHIP RES.(1608) 1/10W 0 _1 RRXAZR5Z0000 Before replacing any of these components, read CHIP CERAMIC CAR CH J 330pF/50V CHD1JJ3CH331 carefully the product safety notice in this service CHIP CERAMIC CAR CH J 330pF/50V...
Page 50
Ref, No. Description Part No. Ref. No. Description Part No. C753 CHIP CERAMIC CAR B K 1500pF/50V CHD1JK30B152 C1205 CHIP CERAMIC CAR(1608) F Z 0.1p F/25V CHD1EZ30F104 C754 CHIP CERAMIC CAR B K 1500pF/50V CHD1JK30B152 C1206 ELECTROLYTIC CAR 100# F/16V M CE1CMASDL101 C766 CHIP CERAMIC CAR(1608) F Z 0.1# F/25V...
Page 51
Ref. No. Description Part No. Ref, No, Description Part No, D470 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1705 CH P CERAM C CAR FZ lpF/10V CHD1AZ30F105 CONNECTORS D471 SWITCHING DIODE 1SS133(T-77) QDTZOO1SS133 CN4Ol BACK LIGHT CONNECTOR 1717369-1 JB17DO2APOO1 D472 SWITCHING DIODE 1SS133(T-77) QDTZOO1SS133 CN4O2 BACK LIGHT CONNECTOR 1717369-1...