Download  Print this page

GE 19208 Installation Instructions Manual

Battery operated wireless door chime kit.
Hide thumbs
   

Advertisement

Wireless Door Chime Kit
Installation Instructions for Battery Operated
Wireless Door Chime Kit
Prior to Installation the Try-Me feature must be removed.
1. Remove the battery cover on the chime.
2. Remove the white Styrofoam block
3. Unplug the red and black wires inside the battery compartment.
4. Remove the battery pack and discard appropriately.
Chime components
Required Tools: Small flat blade screwdriver, drill, 1/16" and 5/32" drill bits,
and phillips screwdriver.
Included Hardware:
(2) Plastic screw anchors
(2) 4x20mm screws
(2) 3x20mm screws
(2) Double sided adhesive pads
GE Model 19208
www.jascoproducts.com
House Code
Door
Try-Me Wires
Styrofoam
Block

Advertisement

   Also See for GE 19208

   Related Manuals for GE 19208

   Summary of Contents for GE 19208

  • Page 1 GE Model 19208 www.jascoproducts.com Wireless Door Chime Kit Installation Instructions for Battery Operated Wireless Door Chime Kit Prior to Installation the Try-Me feature must be removed. 1. Remove the battery cover on the chime. 2. Remove the white Styrofoam block 3.
  • Page 2: Chime Tune Setting

    The wireless door chime Kit has two components: Chime (receiver) Push-Button (Transmitter). Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each push button is set with dip switches 1-3. Single Push Button Kit: If you purchased a kit with a single push button, the chime tune will be set to Ding Dong from the factory.
  • Page 3: Setting House Security Code

    Chime Dip Switches (Ding Dong Shown) House Code Jumpers Pushbutton Dip Switches and Jumpers Setting The House Security Code Each chime component has 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings for the house security code.
  • Page 4 3. Locate the House Security Code door and screw located on the back of the chime (See the chime components picture above). Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shown below. House Code Jumpers Chime and Pushbutton Jumpers 5.
  • Page 5: Mounting Instructions

    Push Button Mounting Instructions Note: Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. Do not mount in an area where exposed to direct rain. a. Removing the back cover b. Replacing the back cover 1.
  • Page 6 Not farther than 150 feet Place push button where you would like to mount and test operation with the chime as close to it’s final location as possible. If it works, mount button here. If it does not work, see TROUBLESHOOTING. Use back cover of push button as a template to mark two screw holes.
  • Page 7 Test Operations, if chime does not work, see TROUBLESHOOTING. Chime Unit Mounting Instructions Note: Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. Select chime mounting location. Use the supplied chime template to mark mounting holes. Drill 5/32”...
  • Page 8: Troubleshooting

    Operation Slide power switch to “On” to turn on the chime. Gently press transmitter button to sound chime. Troubleshooting Chime doesn't work: Make sure push button switch is depressed and held for at least 1 second. Make sure house code switches 1-4 on chime and push button match exactly.
  • Page 9 For technical support contact Jasco Products Company at 1-800-654-8483 or www.jascoproducts.com Made in China Hecho en China is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. www.jascoproducts.com Rev.

Comments to this Manuals

Symbols: 0
Latest comments:
  • Gary Dantzler Mar 31, 2017 05:02:
    Bought mine second hand. Don't even know what the button cell batteries are for or even if they are needed.
  • Eddie Thomas Sep 13, 2016 12:00:
    Can't find the size of the button cell batteries for a 19208 wireless door chime