Page 1 _ave This Manual For Future Reference ..q/ _AIRS Operators Manual MODEL NO. 113.197410 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 2 DOORS MODEL 113.197610 113.197610 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 6 DRAWERS MODEL 113.197410 Serial I:RRFTgMRN Number...
Page 2 FULL YEAR WARRANTY CRAFTSMAN RADIAL If within one year Irom the date of purchase, this Craftsman Radial Saw tails due to a delecl in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY...
Page 3 Safety Information Major Hazards The operator's manual contains safety infor- mation, instructions and signs for your protec- tion against serious injuries, including: 1. Workpiece Kickback Loss of fingers, hand, arm or leg from contact Kickback is an uncontrolled grabbing with the saw blade. throwing of the workpiece during ripping.
Page 4 3. Wrong Feed Wrong way feed is feeding the workpiece into the end of the saw with the anti-kickback pawls. The workpiece can be grabbed by the can be blinded. blade and pull your hands into the blade before you can let go or pull back. Fingers, Wear safety hand or arm can be cut off.
Page 5 Saw Safety Personal Safety 1. Keep guards and anti-kickback pawls in 1. Wear safety goggles labeled "ANSI Z87.1" place and in working order. on the package. Do not wear regular glasses, they are not safety glasses. 2. Check for broken or damaged parts before using saw.
Page 6 Safety Labels on the Radial Arm Saw 14.Rip workpieces that are longer than diameter of the blade being used. Do not rip The following labels are on your radial arm a workpiece that is shorter than the diameter saw. Locate, read and follow the safety in- of the blade being used.
Page 7 Putting Your Saw Together of each of the smaller boxes together and Your radial arm saw is easy to put together, however it will take time. Ask a friend to separate from the others. This will help you help, and follow these assembly instructions. identify and locate the parts you need during assembly.
Page 8 The following parts are included with model 113.197410: Basic Saw Assembly ....Operator's Manual ....Cabinet Box ...... Medium Screwdriver Loose Parts Bags ....Trim Caps ....... 7/16" Wrench Rear Table ......#2 Phillips Screwdriver 1/2" Wrench Spacer ......9/16" Wrench Fence ......
Page 9 The following loose parts are included with Slotted Screws 1/4-20x7/16 ..N° model 113.197410: Truss Head Bolts 1/4-20xl/2 ..Leveling Feet ..... Hex Nuts 1/4-20 ....Hex Nuts 3/8-16 ....Lockwashers 1/4 ....Truss Head Bolts 1/4-20xl/2 ..Spacers ......Lockwashers 1/4 ....
Page 10 The following loose parts are included with both models: Handwheel ...... Arbor Wrenches ....©R ©w Yoke Plug ....... Yellow On/Off Key ....Battery 6V, alkaline, size J ..Pan Head Screw 10-32xl/2 ..Lockwasher 10 ....® © Battery Cover ....
Page 11 1. Turn the shelf upside down on the floor. The wide edge should point down, and the three narrow edges should point up. (Figure Fig. 16 - Truss Head Bolt, Lockwasher, Hex Nut Rear Shelf Stiffener 4. As you assemble your radial arm saw, some of the holes in the parts will line up Under Support...
Page 12 6. Put truss head bolts through the eight holes indicated. Put a lockwasher and hex nut on each bolt tighten using a 7/16 inch wrench or socket. 7. Put a comer bracket in each corner of the shelf (Figure Long End Of Shelf Long End Of Shelf Fig.
Page 13 6. Put a groovedpin through the hole in the of identical parts. These will be put together rod. into left and right foot assemblies which are mirror images of each other. (Figure 22) 7. Put a washer and spring in place on the bot- tom of the rod, and then slide the rod all the way down.
Page 14 9. Apply a few drops of oil (SAE No. 10W-30 15. Screw the leveling foot into the rod until the hex nut reaches the bottom of the rod. automotive engine oil) to the lever where passes through the square hole in the rod. (Figure 10.
Page 15 2. Grease the twelve center slides on top and 2. Lock the lever on the right foot assembly bottom using the grease packets included with the down position. your saw. 3. Attach this foot assembly to the right side 3. Slide each center slide into an outer bracket. panel by sticking the lever through...
Page 16 Rear 11. Put bolts through the four holes along the bottom edge of the right side panel. Put a Short lockwasher and hex nut on each bolt and tighten using a 7/16 inch wrench or socket. (Figure Note: It is sometimes difficult to get bolts Rear Support-...
Page 17 Rear Fig. 40 - Truss Head Bolt Right Side Panel 22. Put a lockwasher and hex nut on the bolt and tighten using a 7/16 wrench or socket. 23. Repeat steps 20 - 22 with the left foot sembly. Shelf 24.
Page 18 31. Put the last two slide brackets in place on sure that you attach the larger hole in each each side of the front and rear supports. Make slide bracket to the rear support. Put a lock- sure that the larger holes in the slide brackets washer and hex nut on each bolt and tighten are in line with the rear support.
Page 19 37. Tighten all screws, except those on the front and rear skirts, using a 7/16 inch wrench or socket. Drawer Front Drawer Putting Drawers Together ,_/_ F)stener The following parts are used to assemble the drawers in model 113.197610: 10 inch Drawers ....
Page 20 4. Place the lower support under the shelf. It should rest directly below the under support, with the angled end sticking out. Line up the four holes in these three pieces. (Figure Note: The angled end of the lower support is a useful way to tell the front of the cabinet from the back.
Page 21 13. Put two truss head bolts through right side 10. Find the right and left side panels. Look panel and spacer, one on each side. carefully to find the "R" and "L" stamped in the metal near the center of the wide edge. 14.
Page 22 23. Use eight truss head bolts, lockwashers, Angled End Of and hex nuts to hold the skirts in place. Hand- Lower Support tighten. (Figure 24. Put a truss head bolt through the hole at the back, right corner of the shelf. This hole goes through the shelf and the right side panel.
Page 23 28. Put a lockwasher and hex nut on the bolt 37. Adjust the lower nut with the 9/16 inch and tighten using a 7/16 inch wrench or sock- wrench until the leveling foot is at the desired height. 38. Tighten the top nut by hand. 29.
Page 24 Rear Skirt Front Skirt Upper Support 1. Lay the two doors side by side. 2. Put a magnetic catch on the inside edge of each door. (Figure Doors Front / Support Angled End Of Cower Support F_. 58 44. Put two truss head bolts through the rear skirt and the upper support.
Page 25 Mounting the Motor Both Models Fig. 63 - Pan Head Screw WARNING: Plugging the saw in 5. Attach the doors to the hinges on the side during assembly can result in electrical panels using eight plastite screws. Tighten shock or your fingers, hand, or arm with a Phillips screwdriver.
Page 26 8. Slide the bevel encoder to the top center 14. Lock the bevel lock. position so it will fit into the notch on the motor support bracket. (Figure 15. Snap the yoke plug into place. The yoke 9. Slide the motor onto the motorpivot sup- plug is in the loose parts bag.
Page 27 Fig. 7"2 3. Repeat steps 1 and 2 on the other side of the saw. Fig. 70 Trim Cap Mounting Large Table Rails Both Models The following parts are used to mount the large table rails: Mounting Small Table Rails Both Models Large Table Rail ....
Page 28 Mounting the Front Table U-Clip On Both ModeLs _ Center Channel The following parts are used to mount front table: Tee Nuts ......U-Clips, 1/4-20 ....Mounting Screws, 1/4-20xl-3/4 ..Rubber Grommets ....Hex Nuts, 1/4-20 ....Washers, 17/64-5/8xl/32 ... Bolt, 1/4-20xl ....
Page 29 1. The steel spacer has a smaller end that fits 7. Place the front table on the saw so that the mounting screws line up with the U-clips. into the large hole on the pivot arm/cam. The front table should extend about one inch...
Page 30 Putting Drawers in Place 4. Try the drawer again. Model 113.197610 5. Repeat until none of the drawers fall out. 1. Slide each drawer in place on the slide Removing Drawers brackets and push them all the way in. Model 113.197610 2.
Page 31 Location and Function of Controls 113.197610 113.197410 Fig. 85 - Radial Saw Controls WARNING: The saw can start ac- On/Off Switch cidentally or be used by children others when the yellow key is left in the to the saw The or_"off switch turns the power red switch.
Page 32 Bevel Lock The bevel lock is used to hold the blade at various angles to the table. To unlock bevel lock, move the lock to the right. Always hold the motor when you unlock the bevel lock. (Figure _i, CAUTION: The motor is heavy and can swing down quickly.
Page 33 swivel lock when the motor is in one of these There are five pre-set bevel angles at -90 °, -45 °, 0°, 45 °, and 90 °. To unlock the bevel positions, stand facing the saw handle, pull lock when the blade is at one of these angles, the swivel lock all the way toward you, and turn the motor as you hold the lock in this move the bevel lock all the way to the right...
Page 34 Handwheel The handwheel controls the height of the radial arm. To raise the radial arm, turn the handwheel clockwise. To lower the radial arm, turn the handwheel counterclockwise. (Figure 95) Fig. 95 - Handwheel One complete turn of the handwheel moves the arm 1/16 inch.
Page 35 Alignment of the Blade 1. Use a 3/16" hex "L" wrench to loosen ALIGNMENT OF THE BLADE IS THE MOST IMPORTANT STEP four screws in the front of the column sup- "L ASSEMBLING YOUR RADIAL SAW. port. (Figure The blade of your radial arm saw must be aligned properly...
Page 36 column rocks back and forth, tighten 2. Raise the radial arm until the bottom four bolts in the back of the column slightly the motor is about 2-1/2 inches above the (Figure 97) and go back to step 2. front table. 3.
Page 37 8. Unlock the miter lock and swing the arm to 18. Move the arbor shaft over another point. the right until the arborshaft is over the right Do not change the elevation of the arm. line at the front of the table. 19.
Page 38 Fig. 102 Fig. 103 25. Lock the bevel lock, rip lock, swivel lock 4. Unlock the rip lock and move the motor and miter lock until the motor arbor is over the front table. 5. Lock the rip lock, miter lock and bevel Squaring Crosscut Travel lock.
Page 39 12. Slightly loosen the bottom two screws. If the motor arbor moves away from the square or tries to "walk" on top of it, go to 13. Use the top two screws to move the radial step 11. (Figure 104) arm into line: If the motor arbor moved away from the...
Page 40 18. Lay a framing square on the front table blade, and the teeth are pointing down at the with the long edge along the back of the table front side of the blade. (Figure 106) and the short edge alongside the motor arbor, as before.
Page 41 9. Loosen the four screws behind the yoke using a 3/16 inch hex-L wrench. (Figure 109) Square _. 4 Socket _Setscrews Fig. 107 6. Turn the blade with your hand several times and check to see if the square is flush with the Fig.
Page 42 Fence Squaring Blade to Fence These steps are done so that your blade will Square be perpendicular to the fence. This will help Right reduce the risk of kickback when ripping, and splintering of the workpiece and burning of the kerr when ripping and crosscutting. Fence Fence Square...
Page 43 8. Hold the square in place and turn the motor until the square is flush with the blade. 9. Hold the saw handle tightly and lock the swivel lock. 10. Check the square to make sure it is still flush with the blade. 11.
Page 44 8. Hold the bolt firmly, and retighten the hex 4. Turn the blade with your hand several times and check to see if the square is flush nut using a 1/2 inch wrench. with the blade. 9. Turn the blade several times and check to see if the square is still flush with the blade.
Page 45 Making Blade Parallel 15. If you can keep either of the carriage bear- ings from turning while the motor moves Table along the radial arm, go to step 16, or These steps are done to help prevent If you cannot keep the carriage bearings from workpiece from being thrown or damaged...
Page 46 Right 5. Place the corner of the flaming square against the fence so that the long edge is on the table under the blade and the short edge Square _4otor is sticking up in the air. Make sure that the Fenc_ long edge is perpendicular to the fence.
Page 47 11. Hold the square in place, and lift or lower WARNING: Kickback can occur if the bottom side of the motor support until the the spreader is not in line with the square is flush with the blade. blade. You can be injured or killed. Al- ways adjust the spreader and make sure 12.
Page 48 4. Tighten the guard clamp screw. 5. Unlock the swivel lock and turn the motor to the in-rip position, with the blade between Guard the motor and the fence. (Figure 125) Antikickback Pawl= )reader Fence Table Fig. 126 Fig. 125 - In-rip Position 12.
Page 49 A - Right 14. Slide the spreader with your hand until it is against the fence directly behind the blade. 15. Tighten both nuts using a 1/2 inch wrench. Do not move the spreader as you tighten these nuts. Pawl-_-_ _ 16.
Page 50 Digital Display ELEV: This button displays the height of the / CRR FTSMRN blade. The "0" display is usually set with the blade just touching the table. A positive dis- play shows the distance the blade has been raised above "0". A negative display shows the distance the blade has been lowered...
Page 51 5. If there is still no display, contact your Installing the Battery nearest Sears store, or 1. Slide the battery into the opening behind If the display says: the digital display with the angled corner on top. (Figure 130) go to step 6. Battery 6.
Page 52 6. Unlock the miter lock. 7. Move the arm to the right until it snaps into the 45 ° position. 8. Lock the miter lock. 9. The display should say: I " s01 10. Unlock the miter lock. 11. Move the arm to the left until it snaps into the -45°position.
Page 53 Bevel Encoder 14. lfthe display is correct at all three points, go to the next section, or 1. Push the ON/OFF button to turn the dis- play on. It"the display is not correct at one or more of these points, go to step 15. 2.
Page 54 8. Push the ELEVbutton. 22. If the display is still not correct, repeat steps 15 - 21 until the bevel encoder is in the 9. Push the REF SET button. right position, 10. The display will say: If the display is correct, go to the next section.
Page 55 8. Lock the @ lock. go to the next section, 9. Push the RIP button. If the display says: I sn° ! 10. If the display shows the O-RIP function, !_!.L! go to step 11, or If the display shows the RIP function, push the RIP button again.
Page 56 iiiiii Electrical Connections WARNING: To avoid shock or fire, if Motor Specifications power cord is worn, cut, or damaged any way have it replaced immediately. The AC motor used in this saw is a capacitor- start, non-reversible type having the following If your unit is for use on less than 120V it has a specifications: plug that looks like below.
Page 57 Extension Cords _1_ WARNING: To maintain proper tool grounding, whenever the outlet you The use of any extension cord will cause are planning to use for this power tool some loss of power. Use the following table is of the two prong type do not remove to determine the minimum wire size or alter the grounding...
Page 58 Crosscutting Crosscutting is used to cut a workpiece length. The workpiece is held against the fence. The saw blade is pulled through workpiece. Cuts are usually made across the grain of the workpiece. Types of Crosscuts The basic types of crosscuts are shown below.
Page 59 4. Fingers or hand can slip into the saw Safety Information blade as you make a crosscut. Fingers, Crosscutting hand or arm can be cut off. Keep the hand holding the workpiece at least 8 in- Read and follow the safety information below ches to the side of the workpiece, out of...
Page 60 10. The workpiece cannot be controlled Blade Guard, Anti-Kickback or held stable enough to do free hand Pawls and Spreader cutting. The workpiece can be thrown slip and pull fingers and hand into the The blade guard, anti-kickback pawls and saw blade.
Page 61 Cutting Table and Fence Crosscutting Checklist Kerfs Use the following checklist at the beginning You will need to cut a new table kerf (shal- of each new cutting period to reduce the risk low cut) and fence kerf (slot left in the fence of an accident.
Page 62 WARNING: The saw blade will sud- 8. Grasp saw handle and hold your forearm in line with the saw handle as shown below. denly come toward you when lowered into the table if the rip lock is unlocked. Fingers and hand can be cut off. Lock the rip lock before and after each crosscut.
Page 63 4. Adjust the height of the anti-kickback Making Crosscuts pawls to clear top of fence and workpiece about 1/8 inch. The pawls and spreader help The following section contains safety informa- provide protection from the leading edge of tion and instructions for making crosscuts.
Page 64 12. Support and hold the workpiece down Pull the saw blade through and against the fence firmly with your left workpiece to the distance shown below. hand. 13. Pull blade through fence and workpiece just enough to complete the cut. Fig. 146. 14.
Page 65 Ripping When to Use In-Rip or Out-Rip Ripping is used to change the width of the workpiece by sawing along its length. The The in-rip saw position provides better workpiece is fed into the saw blade. The visibility of both the workpiece and your fence is used as a guide.
Page 66 2. One of the most common and the Safety Information most dangerous mistakes people make Ripping is to reach for the workpiece at the out- feed side of the saw. DON'T ! The Read and follow the safety information below workpiece could kickback as you reach...
Page 67 4. Non-thru cuts increase the chance 2. The workpiece can be grabbed by the saw blade and take off like a missile. kickback because the anti-kickback Anyone standing in the path of the pawls cannot always grab the irregular workpiece can be killed.
Page 68 Blade Guard, Anti-kickback Rip Cutting ChecMist Pawls and Spreader Use the following rip cutting checklist at the The blade guard, anti-kickback pawls and beginning of each new cutting period workpiece spreader are designed to reduce or reduce the risk of an accident. eliminate the risk of injury from blade con- tact, workpiece kickback and wrong way feed.
Page 69 Blade Guard Adjustments Making a Rip Cut Table Kerf 1. Unplug saw and remove yellow key. You will need to make a table kerf before rip cut can be made. Every time you move 2. Put saw in In-Rip position and lock the the blade a new distance...
Page 70 Anti-kickback Pawls and Spreader Adjust- Making Rip Cuts ments When to Use In-Rip or Out-Rip 1. Go to the outfeed end of the saw blade. The in-rip saw position provides better 2. Put edge of workpiece beside the blade visibility of both the workpiece and your and under the pawls.
Page 71 411kWARNING: When making through 9. Stand out of the line of the workpiece to rip cuts do not set the blade closer than be clear of workpiece in case of kickback. 1/2 inch from the fence or auxiliary fence, your hands will be brought too close to the blade.
Page 72 on the arbor could cause the dado and arbor nut to spin off. Take several passes of the dado if cut required is greater than 13/16 of Kickback, Blade Contact. an inch wide. Fingers, hand, 3. To avoid excessive load on the motor be cut off.
Page 73 _Ib WARNING: 3. Remove saw blade, dado, or other acces- If the auxiliary fence is sory from the saw arbor shaft before using not used when the saw arm is in the 0 ° the accessory shaft. Do not use the saw with crosscut position, the molding...
Page 74 i,iiiiiii Cutting Accessories Push Stick Fences Push sticks are used during ripping when the Fences are required for all saw operations. blade is placed between 2 and 6 inches from the fence. Crosscutting requires fences with kerfs (slots) to match the path of the saw, because the saw Make a push...
Page 75 Auxiliary Fence and Push Block An auxiliary fence must be used if the blade is positioned between 1/2 inch and 2 inches from the fence during ripping. An auxiliary 314" Plywood fence must always be used with a push block. Their purpose is to keep your hands away...
Page 76 5. Cut out a notch from the 12 inch side of Auxiliary Fence for Edging the 3/8 plywood that is 9 1/2 inches long by 3/8 inch wide. The dimensions of the remain- Make an auxiliary fence for edging: ing 3/8 plywood are shown in Fig.
Page 77 Featherboard Featherboards are used during rip cutting to help keep the workpiece against the fence. The featherboard is damped to the front table, so that the angled edge of the feather- board is against the workpiece on the infeed end of the blade. The other edge of the workpiece is against the fence.
Page 78 Sears Recommends The Following Accessories Cat. No. Item blades (10" diameter with 5/8" hole) See Catalog 9-22254 Caster 9-25246 Sanding Drum 9-2980 Drill Chuck Dust Collector See Catalog 9-29523 Molding Head Guard 8" 9-3233 Taper Auxiliary Table Cover See Catalog 9-32056 Miter Square...
Page 79 LowerBlade GuardSafetyInformation WARNING IMPORTANT Remove the lower blade guard for ALL other The following safety information and instruc- types of cuts except repetitive 90 ° crosscut- tions apply to all blades and accessories. ting. Using the lower guard other than for re- The lower blade guard is required by the Oc- petitive 90 °...
Page 80 Glossary Anti-kickback Pawls: Pivoted objects with Molding Cut: Non-through cut which teeth which help prevent workpiece kickback. produces a contoured surface on the workpiece. Arbor: The bar or shaft that holds the saw blade. Outfeed: The end of the saw blade where the rip cut workpiece leaves the saw blade;...
Page 81 Helpful Hints 3. Place the same edge of the workpiece In order to get accurate cutting results from your radial arm saw, do the following: against the fence for all cuts. Make the first cut at one end of the workpiece, then flip the workpiece over and make the 1.
Page 82 3. Lock the miter, bevel, or swivel lock. To extend the life of the front table of your saw, tack a piece of 1/4 inch plywood over it. Make sure that the tacks are not in the path of the saw blade. These steps will reduce stress on saw parts, and improve the accuracy of your cuts.
Page 83 Lubrication taining or lubricating your saw. Your saw is precision built and should be When you receive your new Craftsman radial kept properly lubricated. Before describing saw, it requires no lubrication. The radial...
Page 84 • Lubricate the cam surfaces of the rip lock assembly. A light film of oil should be wiped on the face of the column tube to lubricate the fit between the column tube and column support. Turn the elevation handwheel to raise the arm to its upper limit.
Page 85 Adjustments for Wear 5. Adjustment is complete when both locking and indexing functions are working properly. Bevel Lock Replace motor support cover. The purpose of the bevel lock is to lock the motor at any bevel angle. An adjustment is Swivel Lock required if the motor can be easily moved by hand when the bevel lock is locked or if bevel...
Page 86 Column With the miter lock unlocked and in the unin- dexed position the arm should fit snugly to the column tube and not allow any vertical movement. If you can move the end of the arm up and down an adjustment is needed.
Page 87 2. Push the carriage back against the rear stop. 3. Hold the front carriage bearing with your fingers as tight as possible and pull carriage forward at the same time. If you can prevent the bearing from turning an adjustment required.
Page 88 Rip Lock Miter Lock Handle The ffp lock locks the carriage in any position along the length of the arm. If the carriage can be easily moved by pushing and pulling on the yoke handle when the rip lock is in the locked position an adjustment is required.
Page 89 3. As soon as the red button will click into Motor running position, the saw may be started and operated normally. To avoid motor damage this motor should be blown out or vacuumed frequently to prevent 4. Frequent blowing of fuses or tripping of cir- sawdust buildup which will interfere with nor- cuit breakers may result if: mal motor ventilation.
Page 90 Changing Motor Voltage BOTH MODELS DANGER: To avoid electric shock unplug the saw before changing motor voltage. Under normal home workshop usage, and if Dual Voltage Switch full voltage is supplied to the motor, your saw will operate efficiently on 120V, as connected at the factory.
Page 91 Troubleshooting d_E WARNING: To avoid injury turn power switch off and remove plug from power source outlet before troubleshooting. Electronics Problem Probable Cause What to Do Battery not installed correctly. Adjust battery position in com- No display when On/Off button is pressed. partment.
Page 92 Electronics Problem Probable Cause What to Do Display shows EEE.E Arm or carriage moved Follow procedure for setting EE.EE. rapidly for indicator to monitor, zero reference points in the Set- ting Electronic Display section. Display will reset to zero Encoder or indicator display Have electronics checked by defective.
Page 93 Motor - 2 Problem Probable Cause What to Do Power line overloaded with Reduce the line load. Motor fails to develop full lights, appliances, and other power. motors. (Power output of motor decreases rapidly with Undersize wires or circuit too Increase wire sizes, or reduce decrease in voltage at motor terminals.
Page 94 Saw Operations What to Do Problem Probable Cause Looseness between column tube Crosscuts not accurate Go to Alignment of the Blade, 0° and 45 ° miter. and column support. Adjusting Elevation. Go to Alignment of the Blade, Crosscut travel not square with fence.
Page 95 Saw Operations Problem Probable Cause What to Do Workpiece kerr rough Go to Alignment of the Blade, blade square with tooth marks from to fence. Squaring Blade to Fence. blade (also called heel). Saw blade not parallel Go to Alignment of the Blade, to table.
Page 96 Saw Operations Problem Probable Cause What to Do Clamping force not suffi- Bevel lock needs adjusting. Go to Maintaining Your Saw, Adjustments for Wear, Bevel cient at bevel angles other than 45 ° . Lock. Depth of cut varies from Table top not parallel with arm.
Page 97 NOTES " "...
Page 98 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 (SEE FIG. (SEE FIG. (SEE FIG. 2) "_ FIGURE...
Page 99 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE Part Part Description Description 816333-1 815797-1 Screw, Pan Rec. Screw, Pan Cross Type "TT" 10-32 x 1/2 Type "AB"...
Page 100 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS, 113.197410 AND 113.197610 FIGURE...
Page 101 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 2 -BASE AND COLUMN ASSEMBLY Part Part IKey Description Description 60339 815772 Bolt, Hex Washer Hd.
Page 102 PARTS LIST FOR CRAFTSMAN 10_' ELECTRONIC RADIAL TAW MODEL NOS. 113.197410 AND 113.197610 MOTOR CORD FIGURE...
Page 103 PART9 LI_T FOil CRAFTSMAN t0" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 3 - YOKE AND MOTOR ASSEMBLY Part Part Description Description STD551012 Yoke Assembly (see Figure 4)
Page 104 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 FIGURE...
Page 105 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number--Not by Key Number FIGURE 4 --YOKE ASSEMBLY Part Part KNeY Description Description STD551131 810214-3 Screw, Low Hd. * Lockwasher, External 5/16 815691...
Page 106 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 and 113.197610 FIGURE...
Page 107 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 and 113.197610 Always order by Part Number - Not by Key Number FIGURE 5 - ARM ASSEMBLY FOR MODEL 113.197410 Part Part Description Description 818239 Arm, Radial 816492 Clip, Wire...
Page 108 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 6 - TABLE ASSEMBLY Key I Part Description 815757 Table, Rear 815755 Table, Spacer 815758 Fence,...
Page 109 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 7 - FOOT ASSEMBLY - MODEL 113.197610 Part Description STD601103 *Screw, Pan Rec. Hcl. Type T 10-32 x 3/8...
Page 110 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 ISEE FIG, Figure 8...
Page 111 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 8 - CABINET ASSEMBLY FOR MODEL 113.197610 Part Part Description Description 805589-5 Screw, Truss Hd. 1/4-20 x 1/2 Drawer Assembly 6 in.
Page 112 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS, 113,197410 AND 113.197610 "r • Figure...
Page 113 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 9 - CABINET ASSEMBLY FOR MODEL 113.197410 Part Part JKey Description Description 805589-5 Screw, Truss Hd., 1/4-20 x 1/2...
Page 114 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 10 - DRAWER ASSEMBLIES 3", 6", 10" Part Description 815912 Drawer Assembly, 3" 815917 Drawer Assembly, 6"...
Page 115 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number 3 ----._E FIGURE 11 - MOTOR ASSEMBLY Part Description 507744 Housing, Motor STD376116 *Capacitor 64950 Screw, Type "T"...
Page 116 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197410 AND 113.197610 Always order by Part Number - Not by Key Number FIGURE 12 - GUARD ASSEMBLY P:,rt Part Description Description Guard 816264-1 STD581050 *Ring, Retaining 120399 11 63270 *Nut, Square 5/16-18...
Page 117 NOTES...
Page 118 NOTES...
Page 119 NOTES...
Page 120 10-INCH DELUXE ELECTRONIC Operators RADIAL SAW Manual SERVICE Now that you have purchased your 10-inch electronic radial saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit.

This manual is also suitable for:

Craftsman 113.197610

Sears Craftsman 113.197410 Operator's Manual

Quick Links

Related Manuals for Sears Craftsman 113.197410

Summary of Contents for Sears Craftsman 113.197410

This manual is also suitable for:

Table of Contents