Summary of Contents for Sears Craftsman 358.352030
Page 1
lsears I CHAIN SAW owner's manual MODEL 358.352030-10"" 358.352060-12" 358.352070-14" CRRFTSMRtl 2.0/'i0" 2.0/'I2" 2.0/14 • Assembly • Maintenance * Operation * Repair Parts CAUTION: Read Rules for Record in the space provided below the Made--and Serial No. of your saw. These numbers are located on the starting instructions...
Page 2
-SAFETY RRST Keep others work area when the saw DON'T running Don't use the saw when you are tired BE CAREFUL Don't start cutting until you llave a clear work area, Oon't climb in a tree with a saw - it is very dangerous. secure tooting, and a planned...
TABLE OF CONTENTS • I'NSTALLING THE BAR AND CHA! N ............FUEL AND OIL ..;............SAWING TECHNIQUES ..............MAINTENANCE ..............GUIDE BAR MAINTENANCE ............CHAIN SHARPENING ..............TEMPERATURE LIMITING MUFFLER INSTRUCTIONS ........_ee [mpo/taf)t /_orJce on page 15 _egatding states [equili[l_q temperature I/miring...
INSTALLING THE BAR AND CHAIN _r Always wear gloves when handling the chain! It is sharp! Remove the bar clamp nut and rear bar clamp screw (FigUre !}. Turn the adjusting screw, setting the pin all the way to the rear (See Figure 5). Place the guide bar slot over the mounting pins and slide it to the rear (Figure 2).
30 ° F, use to restart engine. When restarting a hot ,engine, or one straight Craftsman Bar and (;hain Lubricant. 30 ° to 0°, use 5% which has just been refueled, you may have to choke the diesel fuel or kerosene and 95% Lubricant;...
FELLING (Cutting down a tree) Small Trees - Less than 8- across Direction 1. If there is doubt about the direction fall, "notch" method described _ B, of Fall Make a single felling cut or} the side away from direction of fall.
MAfN_-ENANCE Figu Carburetor Adjustment _" BE CAREFUL! The chain will be moving daring this procedure. Stop the engine. Remove the carburetor cover (Figure 7), Turn the high speed (Figure speed mixture screws clockwise (Figure "8} until they stop. Don't tighten them.
Starter Rope If your rope breaks near the pulley, it can be repaired by th_s .:Figure 10 method. Otherwise, replace the _:ope. Remove the pulley screw and pulley very carefully. The recoil spring lies beneath the pulley. Twist the pulley gently as you pull...
Hold t_e file level, perpendicular to the bar, Figure 14. 9. Always check the depth gauge w_th the depth gauge filing guide after filing, If the depth gauge sticks out, fileitoff File in ONE direction only! Figure 15, with a flat file, Figure 16. Press hard[ Two or three strokes should do it.
Page 12
SEARS CHAIN SAW PARTS LIST Craftsman 2.0-- 10'" (Model 358.352030} Craftsman 2.0--12 _°(Model 358.352060) Craftsman 2.0--14" (Model 358.352070) ,, ,,,,,,,. Optional IUSI_. ON MATING SURFACES temperature limiting OF CRANKCASE HALVES) mUffler cover referred to on page 15.
Page 15
OPTIONAL TEMPERATURE LIMITING MUFFLER COVER In some states, such as California, laws covering chain saws (having internal combustion engines), when used in areas covered by forests, brush or grass (excluding residential lawns and landscaped areas}, necessitate fitting the saw's muffler with an additional heat shield to reduce muffler surface temperatures.
Page 16
The Model Number will be found under the handle with the Serial Number. Always mention the Model Number when requesting service or repair parts for your Chain Saw. All parts listed herein may be ordered from any SEARS, ROEBUCK AND CO. OR SIMPSONS-SEARS LIMITED retail or catalog store.