Regulatory Information; Year 2000 Compliance; Federal Communications Commission (Fcc) - Oki B6100n Safety Information Manual

• Stop operation immediately if your printer produces smoke,
excessive heat, unusual noise, or smell. These conditions
can indicate or result in a fire. Immediately switch off and
unplug the printer, and contact your point of purchase.
• The fuser becomes very hot in normal operation. If a paper
jam has occurred, turn the power off and wait at least 10
minutes before removing the print cartridge and touching
the fuser section.
• Carefully read all setup and operating instructions. Be sure
to save all documents for future reference.
• Read and follow all warning and instruction labels on the
printer.
• Place your printer on a firm, solid surface. If you put it on
something unsteady, it might fall and be damaged.
• If you place it on a soft surface, such as a rug, sofa, or bed,
the vents may be blocked, causing the printer to overheat.
• The printer must be installed near a power outlet which will
remain easily accessible.
• Be certain that your power source matches the rating listed
on the back of the printer. If you aren't sure, check with
your dealer or with your local power company.
• Your printer has a grounded, 3-prong plug as a safety
feature. It will only fit into a grounded outlet. If you can not
plug it in, you probably have an older, non-grounded outlet.
Contact an electrician to have it replaced with a grounded
outlet. Do not use an adapter to defeat the grounding.
• To avoid damaging the power cord, do not put anything on
it or place it where it will be walked on. If the cord becomes
damaged or frayed, replace it immediately.
• If you're using an extension cord or power strip with the
printer, make sure that the total of the amperes required by
all the equipment on the extension is less than the
extension's rating. Generally, the total ratings of all
equipment plugged into any one power line should not
exceed 15 amperes. Don't exceed this unless you know that
the power line your equipment is plugged into has a rating
above 15 amperes.
• Unplug the printer before you clean it. Use only a damp
cloth. Do not use liquid or aerosol cleaners.
• To protect your printer from overheating, make sure no
openings on the printer are blocked. Do not put the printer
on or near a heat source, such as a radiator or heat register.
If you put the printer in any kind of enclosure, make sure it
is well ventilated.
• Do not use your printer near water. Do not spill liquid of
any kind into it.
• Do not poke anything into the ventilation slots on the
printer. You could get a shock or cause a fire.
• Aside from the routine maintenance described in the User's
Guide, don't try to service the printer yourself. Opening the
cover may expose you to shocks or other hazards. Don't
make any adjustments other than those outlined in the
User's Guide. You might cause damage requiring extensive
repair work.
• If anything happens that indicates that your printer is not
working properly or has been damaged, unplug it
immediately. Then, follow the procedures in "Service and
Support" for having your printer serviced.
English
These are some of the things to look for:
– The power cord or plug is frayed or damaged.
– Liquid has been spilled into the housing, or the printer
has been exposed to water.
– The printer has been dropped or its cabinet has been
damaged.
– The printer doesn't function normally when you're
following the operating instructions
.

Regulatory Information

E S
®
NERGY TAR
As an E S Partner, Oki Data has determined that this
NERGY TAR
product meets the E
NERGY
efficiency.

Year 2000 Compliance

This product is Year 2000 Compliant. It contains information
technology that accurately processes date and time data between
the years 1999 and 2000, and carries no issue for the September
9, 1999 (9999) programming concern. This product, when used
in combination with products purchased from other
manufacturers, whose products properly exchange data and time
information, will accurately process the date and time.
Federal Communications Commission
(FCC)
FCC Declaration of Conformity
1. Product Identification
Product Name: B6100
Model No.:
BXJA-7 (120 Volt)
BXJB-2 (230 Volt)
2. Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
3. Responsible Party
Oki Data Americas, Inc.
2000 Bishops Gate Boulevard
Mt. Laurel, NJ 08054-4620
1-800-654-3282 (1-800-OKI-DATA)
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
S guidelines for energy
TAR
5