Maintenance Safety; Troubleshootingchart; Accessories - Craftsman 358.799030 Operator's Manual

2;
tztst_lling Line On Spool
Use .06s" _4_zmeter line only.
• To replace the trimmer line on an ezistfug
spool, do the following:
a. Follow "InstatRu_ Spool w/Line," steps "a.-c., _
and remove any _me remaJni_ug on thespool.
Do not wrap more than 40 feet of.065" di*
ameter line ontothe spool.
b. Hold spool as shown inFigure 15.
c. Insert I 116 to I/8 inchof line through theholein
theinner rimofthespool. Figure 15. Allowno
more t_m.u i /8inchofline toextendbeyondthe
inner rimofthespool toavoid interference with
thedrive gear.
d. Wrap line e venly and firmly in thedirection in-
dicated by thearrowon thespool.Figure 15.
To ensure proper line advance, avoid crossover
or crisscrossing theline.
II l . Jml IIIIIII I II
GENERAL MAENTENANCE
under a loador does
not turnwhen
switch is pressed.
Line does not ad-
vance or breaks
while cutting. €:
d.
e.
Line welds
a.
ontospool,
b.
e.
d.
a.
e. Followinstructions in _Instailing Spool w/
Line, _ steps "f.-j."
• If'the trimmer llne break.soft or backs uv in
the trimmer head, followInstalling Spoolw/
Line/steps "a.-c." Pull slack in theline until i t is
tightly wound on the spool, tea_ng 4-6 inches of
]_e extended. -Continue with Installing Sp0ol wi
_..
Line," s_ps "f.-j."
xrow of Line
,,,, ,
Figure 15
i r , i i H HI . ,
' ' ' ' 1,,","" ............... ., .........
A. MAINTENANCE SAFETY
* t * •
1. Mam la m the tool according to reeom-
men_dp_'_ed_es. K£-epthe cut_Angiineat the
_ropertength.
2. Disconnect power source before performang
m_Lintenanee. 7.
3. K_ep the unit clean. Use a spongedampened
with a sOlUtion o fmildsoapand water.Do notuse
8.
s_qlvents or petroleum bassi cleaner of may kind.
4. Keep air vente free ot debris at all times.
B. TROUBLE SHOOTING CHART
SYMPTOM .......CAUSE .................... ........................
Trimmer Head stops a. Crowding trimmerline against
material beingcut.
Line releases
continu0tLsly.
Line usage is
excessive.
5. ReFlace L_mmer head parts that are cracked,
chipped, broken, or damaged in any other way be-
ford using the tool.
6. Use only .065"diameter llne.Neverusewire,
rope, string, ,etc.
Use only genuine SEARS replacement parts
ai recommended.
Ixmpect the entire tool Replace damaged psxts.
Check for fuel leaks and make sureall fasteners are
inplace and securely f astened.
Line pulls back
into head.
b. Electrical
failure.
c. None 0£ the above.
...,, .,
a. Line improperly routed in head.
b, Line improperly wound ontospool.
Line _size incorrect.
Too little line outside he_&
DL_ a,_umulated on coven
Line size incorrect.
Incorr_ spool.,
Crowdi_ line ags_st material being cuL
Cuttinf at higherspeed _,,necessmT.
Line improperly routed in hea_
b. Line size incorrect.
,JLHm,,,, , ,,,,,,,
a. [£u improperly muted in head.
b. Line size inco_
c. Cuttinff at high speed around hard objects.
d. ,,Crowding RUe S_ainst material
bein_._t. ....
a, Too little Rue outside of head.
b. Linesize incorro_
""I'H{H IIIHHHHHHH H I IIIHH
ACCESSORIES
SAFETY GOGGLES .................
SPOOL W/LINE 06_" DIA.
EXTENSION CORD (100 R.) ..........
BULK LINE --_t00 F_ .............
--200 FT..............
• --400 F_... • ........
' 0P RATOR'S MANUAL .......... ,..
REMEDY ..........................
a. Back trimmer bead away fromgrass being
cut; allowtip of line to. do thecutting.
b. Contactyour SEARS Service C enter/Depc.
_.€" Contact _our S_RS
Service C enter/Dept.
8- Remove cove_ Check line routing.
b.r md
eve.ly.
c. Use only.06_ dlameterllne,
& Remove cover. Pu]t4" of line to outside.
e. CI_ coyer.
a. Use only .065" diameter llne.
b. Use proper spool.
e. Cut with tip of line.
d. Reducecutting speed.
a. Remove cover.Check line routing.
b. Use only ,,06_" _eter line. ......
a. Remove cover. Check [ine routing.
b. Use only.06_" diameter line.
c. Reducespeed around hard objects.
d: cut
o,, tine.
a. Remove cover.Pull4" ofline tooutside.
b. Use only .065" diameterline.
III Hill IIII { HI I l, lii ..............
....................... STOC NO. .......
............................................. 71-85707
.............................................. 71-85830
.............................................
71-;57020
,,,_......................................... 71-85772
........ , .................................... 7Z-85607
. .............. : ....................... . .....
71_769
................ _ ............................ _30-068416
" , • .