1. Manuals
  2. Brands
  3. a/d/s/ Manuals
  4. Speakers
  5. HT300iw
  6. Owner's manual

a/d/s/ HT300IW Owner's Manual

Home theatre in-wall speaker system
Hide thumbs Also See for HT300IW:
Table of Contents

Advertisement

Quick Links

HT300iw
HT400iw
HT800iw
owner's manual
analog and digital systems

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HT300IW and is the answer not in the manual?

Questions and answers

Related Manuals for a/d/s/ HT300IW

Summary of Contents for a/d/s/ HT300IW

  • Page 1 HT300iw HT400iw HT800iw owner's manual analog and digital systems...

  • Page 2: Table Of Contents

    table of contents introduction cautions features installation precautions and tips general mounting suggestions prewiring preparing the wall or ceiling cutout final installation custom painting operation specifications warranty information introduction Congratulations, and thank you for purchasing an a/d/s/ Home Theatre in-wall speaker system. The HT- series offer the perfect combination of style and performance to meet the most exacting audio and interior design standards.
  • Page 3 high frequency contour switch A 3-position switch located on the tweeter plate serves as a high frequency contour control. The upper position offers a “normal” response suitable for most applications. The bottom position provides the most output and is recommended for off-axis listening or if the speakers are mounted very high. The center position provides the least and is recommended for reflective “bright”...

  • Page 4: Installation Precautions And Tips

    installation precautions and tips Please read these instructions completely for the best enjoyment of your HT Series speakers. When you cut into the wall to install the speaker, do not cut through the facing or insulation that may be behind the wall. This facing is a moisture barrier. Use duct tape or wide vinyl tape to seal any cuts.

  • Page 5: Preparing The Wall Or Ceiling Cutout

    preparing the wall or ceiling cutout Confirm there is at least 1" between the final cutout and nearby studs or joints for positioning mounting hardware. Temporarily fasten the stiff paper template (supplied) to the wall with thumbtacks. Carefully trace around the perimeter with a pencil. Before making the final cutout of the entire hole, first make a small 4-inch"test"...
  • Page 6 Insert the speaker assembly on an angle so that one of the mounting brackets enters the opening first. (fig. 1) fig1 Turn the speaker toward the wall so that the other mounting bracket enters the mounting hole and the speaker is seated on the wall.

  • Page 7: Custom Painting

    removing the grille Should it be necessary to remove the grille, insert an awl or other pointed tool into a grille hole near the corner. Gently lift the grille out of the speaker frame. Repeat this procedure at each corner of the grille, gradually lifting the corners of the grille until it is removed.

  • Page 8: Specifications

    specifications HT300iw HT400iw HT800iw Mounting hole 6 3/8" x 9 1/8" 6 3/8" x 14 7/8" 6 3/8” x 26 1/2" Depth from front of wall 3 1/4" 3 1/4" 3 1/4" Overall dimensions 7 1/4" x 10 1/8" 7 1/4" x 15 7/8" 7 1/4"...

  • Page 9: Warranty Information

    LIMITED TWO YEAR CONSUMER WARRANTY Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase from the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer.
  • Page 10 Directed Electronics, Inc. All rights reserved G39556/61/71 10-02...

This manual is also suitable for:

Ht800iwHt400iw

Table of Contents