Advertisement
Quick Links
Advertisement
Related Manuals for Diamond Audio Technology D6 1000.2
Summary of Contents for Diamond Audio Technology D6 1000.2
- Page 1 AMPLIFIER INSTALLATION MANUAL D6 450.2 D6 700.4 D6 1000.2 D6 1200.1...
- Page 2 Congratulations! Thank you for choosing a Diamond Audio Technologies D6 Series amplifier. We sincerely believe that D6 amplifiers have the very best performance and value. DAT products are engineered and produced with the highest quality materials and incorporate the latest technology. We think you will find your new DAT amplifier meets or exceeds your expectations and provides excellent value.
- Page 3 Frequency Response: 20Hz to 20KHz +/-3 dB D6 450.2 Signal to Noise Ratio: >95dBA (20 to 20kHz) Channel Separation 50dB THD+N(Total Harmonic Distortion + Noise) <0.2%(Output-1W 4 Ohms) 2-Channel Amplifier RCA Input Sensitivity: 150mV to 4V RCA Input Impedance: >20K Ohms Hi-Level Input Sensitivity: 1.5V to 14V 450 Watts RMS Output Power...
- Page 4 245 x 74mm 245 x 74mm 245 x 74mm 245 x 74mm Connections and Controls This section describes how all of the terminals and adjustments of DAT D6 Series amplifiers function. INPUT SELECTION X-OVER GAIN BASS BOOST SUB SONIC INPUT SELECTION X-OVER GAIN BASS BOOST...
- Page 5 RCA Input and Pass-Thru Output - These RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using RCA type audio cables, keeping them away from power wiring wherever possible. On the 4 channel amplifiers (D6 700.4) “Front”...
-
Page 6: Tools And Supplies
Installation Guidelines Tools and Supplies Listed below are the tools and supplies needed to complete this installation: • Volt/Ohm Meter • Wire strippers and wire cutters • #2 Phillips screwdriver • Battery post wrench • Hand held drill w/assorted bits •... -
Page 7: Mounting Locations
Mounting Locations Engine Compartment Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty. Trunk Mounting Mounting the amplifier vertically will provide adequate cooling of the amplifier. If you will be mounting it to an existing panel, be sure it’s not prone to excessive vibration (such as mounting to the back of a subwoofer enclosure). - Page 8 Trim the power cable within 18 inches (45.7mm) of the positive battery Power Connections post and splice in a in-line fuse holder. DO NOT install the fuse at this time. Strip 1/2 inch (12.7mm) from the battery end of the power cable and crimp a large ring terminal to the cable.
- Page 9 Connecting Multiple Speakers If you must connect more than one speaker per channel, there are two methods in which to do so: Series or Parallel. Parallel connections are harder on the amplifier than series connections, as the total impedance is lower compared to driving a single speaker, and the amplifier must produce more current to drive them.
- Page 10 For more wiring options, see the Support section at www.diamondaudio.com Installing the Remote Level Controller The D6 1200.1 comes packaged with a remote level control. This allows you to control the level by attenu- ating the amplitude or increasing (up to the maximum set-point) of the amplifier’s input gain control. This control does not add additional bass boost, it simply allows you to control the level to suit your tastes.
-
Page 11: Troubleshooting
Adjustment of Built-In Crossover (All Models) Placing the switch in the HP position sets the amplifier to the High Pass mode, enabling frequencies above the cutoff point to pass. Placing the switch in the LP position sets the amplifier to the Low Pass mode, enabling frequencies below the cutoff point to pass. - Page 12 Diamond Audio Warranty Diamond Audio Technologies, LLC (DAT) warrants this product to be free from defects in mate- rial and workmanship for a period of one (1) year from the original date of purchase provided it was purchased from an authorized DAT retailer within the United States. However, if this product was installed by an authorized DAT retailer, the warranty period will be extended to three (3) years.
Need help?
Do you have a question about the D6 1000.2 and is the answer not in the manual?
Questions and answers