Table of Contents
Advertisement
Quick Links
Altec Lansing Pr
Altec Lansing Professional
Altec Lansing Pr
Altec Lansing Pr
Altec Lansing Pr
A division of Altec Lansing Technologies Inc, Milford PA 18337-0277 Made In USA
1662A
Mic/Line Mixer
ofessional
ofessional
ofessional
ofessional
1000 W. Wilshire Blvd. Suite 362
Oklahoma City, OK 73116 USA
Power
Advertisement
Table of Contents
Related Manuals for Altec Lansing 1662A
Summary of Contents for Altec Lansing 1662A
- Page 1 Altec Lansing Pr Altec Lansing Professional Altec Lansing Pr Altec Lansing Pr 1000 W. Wilshire Blvd. Suite 362 Oklahoma City, OK 73116 USA A division of Altec Lansing Technologies Inc, Milford PA 18337-0277 Made In USA 1662A ofessional ofessional ofessional ofessional...
-
Page 2: Table Of Contents
Operating Manual -1662A Mic/Line Mixer Table Of Contents 1 1 1 1 1 INTRODUCTION INTRODUCTION INTRODUCTION INTRODUCTION INTRODUCTION ..........3... -
Page 3: Introduction
Congratulations on your purchase of an Altec Lansing 1662A mic/line mixer, a professional, studio quality solution to everday mixing needs. The 1662A features six mic/line inputs with mic input pad, TRS insert points, and +48V phantom power. Each channel has up to... -
Page 4: Front Pfront Panel Controls Anel Controls Anel Controls
The clip LED turns on whenever any portion of the audio path within the input channel reaches a level 3 dB below actual clipping. Clipping in the 1662A occurs at +23dB. 4.3 T 4.3 T 4.3 Tr r r r r eble and Bass Contr 4.3 T... -
Page 5: Connectors And Cables
5. CONNECTORS AND CABLES 5. CONNECTORS AND CABLES 5. CONNECTORS AND CABLES The 1662A mixer is fitted with three types of audio connectors: 3-pin Euroblock assemblies are used for mic/line inputs and main outputs, 1/ 4" tip-ring-sleeve (TRS) phone jacks are used for individual channel insert points, and RCA jacks are used for sum inputs. -
Page 6: R E A R P R E A R Pa N E L F E A A N E L F E At U R E S A N E L F E A T U R E S T U R E S
Output (pre EQ) for recording individual channels, make a special cable with tip and ring connected at the 1662A end and a tip-sleeve mono plug at the other end. Connecting tip and ring at the mixer insert jack is necessary for uninterrupted signal within the mixer when using direct line outputs. -
Page 7: Troubleshooting Tips
7.2 Distorted Sound Something is being overdriven in the signal path. If the clip indicators are active, reduce the Operating Manual -1662A Mic/Line Mixer channel gain and/or press in the pad switch on the rear panel. There are many gain adjustments in... -
Page 8: Typical Applica Typical Application Tion
TION: TION: TION: TION: In the setup shown here, the 1662A is used to mix typical sound sources that might be found in a church, small club, gym, school theater or similar environment. Channels 1-4 are used for vocal microphones, while the remaining two channels are used for stereo program tracks. -
Page 9: 0 S P E C I F I C A S P E C I F I C A S P E C I F I C At I O N S T I O N S T I O N S
The unit you have just purchased is protected by a limited five-year warranty . For warranty service or to obtain a return RMA number, please call Altec Lansing technical services at 405-848-3108. Fill out the informa- tion below for your records. -
Page 10: Block Diagram
Operating Manual -1662A Mic/Line Mixer 12. 1662A Block Diagram 12. 1662A Block Diagram 12. 1662A Block Diagram 12. 1662A Block Diagram 12. 1662A Block Diagram... - Page 11 Operating Manual -1662A Mic/Line Mixer...
- Page 12 Altec Lansing Professional Altec Lansing Professional Altec Lansing Professional Altec Lansing Professional A division of Altec Lansing Technologies Inc, Milford PA 18337-0277 Made In USA Printed in USA 1000 W. Wilshire Blvd. Suite 362 Oklahoma City, OK 73116 USA 1662A-0 0503...
Need help?
Do you have a question about the 1662A and is the answer not in the manual?
Questions and answers