Advertisement
Quick Links
BIESEMEYER
For use with Biesemeyer® commercial and home shop fences, and other makes of
The cut-off fence is shipped complete in one container. Fig 1, illustrates all components shipped.
1
1. Drilling template (for Biesemeyer
2. Clamp and bracket assembly
3. Knob assembly
4. 1/4-20 x 1" hex head bolt
5. 1/4" flat washer
1. DO NOT use cut-off fence in ripping applications; it is
only to be used with the miter gage to perform cut-offs.
2. ALWAYS make certain saw fence and cut-off fence are
securely fastened before use.
®
MODEL NO. 78-939 CUT-OFF FENCE
Biesemeyer-style fences 3-1/2" or 4" wide
9
Fig. 1
COMPONENTS
®
fences only)
SAFETY RULES
2
6
7
8
6. 1/4-20 locknut
7. #10x 3/4" flat head self-tapping screw
8. 6" cut-off fence support
9. Cut-off fence board
3. ALWAYS turn the saw off and allow the saw blade to
come to a complete stop before attempting to remove
cut-off pieces.
4. AVOID trapping the workpiece between the fence and
saw blade. The piece of wood being cut must be past the
cut-off fence before contacting the saw blade.
Part No. 1341095
Dated 4-30-99
3
5
4
Advertisement
Summary of Contents for Delta BIESEMEYER 78-939
-
Page 1: Safety Rules
Part No. 1341095 Dated 4-30-99 ® BIESEMEYER MODEL NO. 78-939 CUT-OFF FENCE For use with Biesemeyer® commercial and home shop fences, and other makes of Biesemeyer-style fences 3-1/2” or 4” wide The cut-off fence is shipped complete in one container. Fig 1, illustrates all components shipped. Fig. - Page 2 ASSEMBLY DISCONNECT SAW FROM POWER SOURCE UNTIL ALL ASSEMBLY AND SET-UP PROCEDURES HAVE BEEN COMPLETED. ® FOR BIESEMEYER COMMERCIAL OR HOME SHOP FENCES ONLY. 1. Fold template (A) Fig. 2, on fold line and align the template with the bottom of fence board (B). Using a punch, mark the fence board (B) as indicated on the template (A) for Commercial or Home Shop installation.
- Page 3 FOR ALL FENCES 8. Using a 1/8” drill bit, drill two 1/8” pilot holes 1/2” deep at the two marked locations on the back of cut-off fence board (F) Figs. 5 and 6. NOTE: Mark the drill bit with masking tape to act as a depth gage to prevent drilling through fence board.
-
Page 4: Setup And Use
Fig. 10 SET-UP AND USE DISCONNECT SAW FROM POWER SOURCE 1. Place entire cut-off fence (X) Fig. 10, so it straddles saw fence (D), and is positioned close to the front edge of saw table as shown. Then tighten knob (T). WARNING: ALWAYS POSITION CUT-OFF FENCE (X) FIG. -
Page 5: Replacement Parts
REPLACEMENT PARTS 78-939 CUT-OFF FENCE REF. PART NUMBER DESCRIPTION 78-939 CUT-OFF FENCE, CONST OF: 1350066 KNOB ASSEMBLY 1352363 CLAMP 1350191 END CAP 1350303 1/4-20 X 1-1/2” HEX HD SCREW 1350295 1/4-20 X 1/2” HEX HD SCREW 1350077 FLAG DECAL 1350300 #10 X 4/4”... -
Page 6: Parts, Service Or Warranty Assistance
Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the cus- tomer notifies his supplying distributor of the alleged defect within two years from the date of delivery to him, of the product and provides Delta Machinery with reasonable opportunity to verify the defect by inspection. - Page 8 THIS PAGE INTENTIONALLY LEFT BLANK\...