Tachometer Setup - Dakota Digital MCL-2004(-R Manual

TACHOMETER SETUP

The digital tachometer update rate can be adjusted between slow, mid, and fast. The rpm warning/shift point can
be adjusted from 2000 – 7500 RPM. The bar graph color can also be changed from green with a red warning to red with a
green warning.
v v v v PdAtE PdAtE Display update setup
PdAtE PdAtE
The display update will select how quickly the digital tachometer reading will respond.
Press and release the switch until "vPdAtE" is displayed, then press and hold the switch until " - " is displayed.
Release the switch. The update setting will be displayed. (1=slow, 2=mid, 3=fast).
Press and release the switch until the desired setting is displayed.
Press and hold the switch until " - " is displayed to save the setting.
RPM
W W W W X X X X Arn Arn Arn Arn Rpm warning setup
Press and release the switch until "WXArn
Release the switch. The current warning point will be displayed on the bar graph.
Press and release the switch until the desired setting is displayed.
Press and hold the switch until " - " is displayed to save the setting.
RPM
Color Color Color Color Bar graph color selection
Press and release the switch until "Color
Release the switch. The tach bar will light up in the current color (green or red).
Press and release the switch until the desired color is displayed.
Press and hold the switch until " - " is displayed to save the setting.
V
W W W W X X X X Arn Arn Arn Arn Voltage warning setup
Press and release the switch until "WXArn
Release the switch. The current warning point will be displayed (9.0 – 12.1).
Press and release the switch until the desired setting is displayed.
Press and hold the switch until " - " is displayed to save the setting.
Sender Sender Sender Sender Pressure sender setup
P
The gauge can use the following Dakota Digital pressure sensors: SEN-1031 (0-150 psi), SEN-1032 (0-75 psi), or SEN-
1035 (0-400 psi)
Press and release the switch until "Sender
Release the switch. The current sender type will be shown (75, 150, or 400).
Press and release the switch until the desired setting is displayed.
Press and hold the switch until " - " is displayed to save the setting.
WXarn WXarn
WXarn WXarn Pressure warning setup
P
Press and release the switch until "WXarn
Release the switch. Lo and number from 5-36 will be displayed for the low pressure warning point.
Press and release the switch until the desired value is displayed.
Press and hold the switch until " - " is displayed to go on to the high warning.
Release the switch. HI and number from 37-75, 75-150, or 150-300 will be displayed for the high pressure warning point
depending on the sender type selected.
Press and release the switch until the desired value is displayed.
Press and hold the switch until " - " is displayed to save the setting.
Set FC Temperature sender setup Set FC Set FC Set FC
The temperature gauge can read the stock head temperature sensor from the ECM or it can use the following Dakota
Digital temperature sensors: SEN-1043 (400F/200C) or SEN-1044(302F/151C)
Press and release the switch until "Set FC" is displayed, then press and hold the switch until " - " is displayed.
Release the switch. The current sender type will be shown with its unit. (HEAD F, HEAD C, 400F, 200C, 302F, or 151C).
Press and release the switch until the desired setting is displayed.
Press and hold the switch until " - " is displayed to save the setting.
HI F-C Temperature warning setup HI F-C HI F-C HI F-C
Press and release the switch until "HI F-C" is displayed, then press and hold the switch until " - " is displayed.
Release the switch. H and number from 200F – 350F or 93C – 176C will be displayed.
Press and release the switch until the desired value is displayed.
Press and hold the switch until " - " is displayed to save the setting.
RPM
" is displayed, then press and hold the switch until " - " is displayed.
RPM
" is displayed, then press and hold the switch until " - " is displayed.
V
" is displayed, then press and hold the switch until " - " is displayed.
" is displayed, then press and hold the switch until " - " is displayed.
P
" is displayed, then press and hold the switch until " - " is displayed.
P
MAN# 650304:F