Table of Contents
Advertisement
Quick Links
Introduction
The Satellite Speaker Mounts - 1 Pair are fully-adjustable (Tilt,
Swivel, & Pivot) speaker wall or ceiling mounts.
Key Features and Benefits
•
Universal design fits most speaker brands & designs
•
Ceiling or wall mountable & compatible with 1, 2, or
4-hole and key-hole speaker mounting (with included
adapters)
•
Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning
•
Holds speakers weighing up to 8 lbs
Serial Number Sticker
For future product return or exchange, this serial number is
required. Please keep it for your reference.
04-0600B
Satellite
Mounts - 1 Pair
Quick Installation Guide
Speaker
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SIIG Satellite Speaker Mounts
-
Page 1: Quick Installation Guide
Satellite Speaker Mounts - 1 Pair Quick Installation Guide Introduction The Satellite Speaker Mounts - 1 Pair are fully-adjustable (Tilt, Swivel, & Pivot) speaker wall or ceiling mounts. Key Features and Benefits • Universal design fits most speaker brands & designs •... -
Page 2: Package Contents
Package Contents • (2) Speaker mounts • (2) 1-hole adapters • (2) 2/4-hole adapters • (2) 2 ¼” ceiling mount extensions • Mounting hardware • Quick installation guide Mounting Hardware M6x20mm Machine Screw M5 x 20mm Machine Screw 8-32 x 5/8" Machine Screw 1/4"-20 x 1/2"... -
Page 3: Installation
Installation Please read the instructions prior to installation. This speaker mount is designed solely for the mounting of small speakers weighing less than 8lbs. We are not responsible for damage that may occur if speakers weighing more than 8lbs. are used. - Page 4 Once the proper configuration is determined, secure the post to the speaker. Some speakers use the smaller M4 x 8 screw, which is inserted into the off-center on the mounting post, see Figure 2 below. M4 x 8mm Flat Head Machine Screw Back Speaker Figure 2...
- Page 5 When the correct size is determined, place the screw through the speaker post and attach to the rear of the speaker enclosure. If the screw does not tighten properly, use the M5 x 1/8" plastic washer to tighten it up. Key Hole Mounting If your speaker has a factory key hole design, you will use the 8-32 x 5/8"...
- Page 6 Engage the hex key hole nut into the key hole slot. Put tension on the assembly by gently pulling back on the speaker mount post while tightening the 8-32 x 5/8" machine screw, see Figure 4 on page 5. The hex key hole nut will engage on the housing in the key hole slot.
- Page 7 Back 1/4"-20 x 1/2" Speaker Machine Screw 4-Hole Orientation 2-Hole Orientation Figure 5 Self-Tapped Mounting Locate the optimum location for the mounting plate and use it as template to mark the drilling locations. Do not drill or screw into the speaker where you could possibly damage the internal components.
- Page 8 #12 x 3/4" Self Back Speaker Tapping Screw Figure 6 Mounting to the Wall or Ceiling The mounting hardware for the three different surface applications is supplied. You will need to determine what style hardware will work best with your mounting surface. Always use caution when drilling into a wall or ceiling.
- Page 9 #12 x 1 3/4" Self Tapping Screw Figure 7 Drill holes through the drywall and into the wood stud using a 1/8" drill bit. These holes should be drilled 1 1/2" deep, see Figure 7 above. After the holes are drilled, mount the wall plate using the self tapping screws.
- Page 10 With the anchors in place, mount the wall plates using the #12 x 3/4" self tapping screws, see Figure 8 below. #12 x 3/4" Self Pre Drill 5/16" Tapping Screw Holes Insert screw through wall plate Insert Alligator and into the alligator anchor Anchor Figure 8 Concrete Surface...
- Page 11 Insert Alligator Anchor #12 x 3/4" Self Tapping Screw Insert screw through wall plate and into the alligator anchor Using the hammer to tap anchor into place Figure 9 With the wall anchor in place, mount the wall plate using the #12 x 3/4" self tapping screws, see Figure 9 above.
-
Page 12: Speaker Mounting
Low-Profile Mounting This is for wall and ceiling application. Install the low-profile portion of the speaker mount to the wall plate or 2 1/4" extension. Secure the setscrew to hold the extension in place with the weight of the speaker attached. Tighten the allen screw using the provided allen wrench. - Page 13 Blank Page...
- Page 14 Blank Page...
-
Page 15: Technical Support And Warranty
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request will be processed, if the product is determined to be defective, an RMA number will be issued. - Page 16 Fremont, CA 94538-3152, USA Phone: 510-657-8688 Satellite Speaker Mounts - 1 Pair is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication are for identification only and may be trademarks of their respective owners.
Need help?
Do you have a question about the Satellite Speaker Mounts and is the answer not in the manual?
Questions and answers