Page 1
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A. HIGH-DEFINITION TELEVISION TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA. IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-256-2487, OR VISIT OUR WEB SITE AT http://www.EmersonAudioVideo.com...
NTRODUCTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
SERVICING - Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualifi ed service personnel. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall outlet and refer servicing to qualifi ed service personnel under the following conditions: a.
NTRODUCTION The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Features • DTV/TV/CATV - You can use your remote control to select channels which are broadcast in digital format and conventional analog format. Also, cable subscribers can access their cable TV channels. • Information Display (DTV only) - You can display the title, contents and other information of the current DTV program on the TV screen.
NTRODUCTION Remote Control Function Installing the Batteries Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control. Battery Precautions: • Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device. •...
Control Panel Rear Panel rear of this unit side of the unit VIDEO 2 COMPONENT AUDIO VIDEO 1 AUDIO S-VIDEO VIDEO COAXIAL 1. POWER button (p11) Press to turn the unit on and off. 2. INPUT SELECT button (p13) POWER •...
ONNECTION Cables not included. Please purchase the necessary cables at your local store. Basic Connection This section describes how to connect the unit to an antenna, cable/satellite box, etc. Note: • Be sure your antenna or other device is connected properly before plugging in the power cord. [Antenna Cable Connection] When connecting the unit to an antenna or cable TV company (without cable/satellite box) Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
Cables not included. Please purchase the necessary cables at your local store. External Device Connection [Component Video Cable Connection] Component video connection offers better picture quality for video devices connected to the unit. Use a component video cable to connect the unit to external video devices equipped with component video output jacks.
ONNECTION Cables not included. Please purchase the necessary cables at your local store. [Video Connection] Video connection offers standard picture quality for video devices connected to the unit. If you connect to the unit’s video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1. When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
NITIAL SETTING These operations are accessible by remote control. Some may also be accessible by controls on the main unit. Initial Setup This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and “AUTO PRESET CH”, which automatically scans and memorizes viewable channels.
NITIAL SETTING • BACK LIGHT You can set the desired brightness mode. (Refer to “Back Light Setting” on page 21.) • COLOR TEMP. You can adjust color temperature (“NORMAL”, “WARM”, “COOL”). (Refer to “Color Temperature” on page 21.) • DTVCC In addition to the basic closed caption described on page 18, DTV has its own closed caption called DTVCC.
ATCHING TV Channel Selection Select channels by using [CH. K / L] or [the Number buttons]. • To select the memorized channels, use [CH. K / L] or [the Number buttons]. • To select the non-memorized channels, use [the Number buttons]. To Use [the Number buttons] - When selecting analog channel 12 - When selecting digital channel 12-1...
ATCHING TV Switching Audio Mode This section describes how to switch the audio in the analog mode and how to switch the audio language in the digital mode. While receiving an MTS broadcast, press [AUDIO ] repeatedly to cycle through the available audio channel. MAIN : Outputs main-audio : Outputs second audio program...
Screen Information You can display the currently selected channel or other information such as the audio mode on the TV screen. In the analog mode, the current channel number is displayed. Press [DISPLAY ]. • The current channel number is displayed at the top- right corner of the TV screen.
ATCHING TV TV Screen Display Mode 3-5 types of display modes can be selected when the broadcasting station is sending 4:3 or 16:9 video signal or an external device is connected to the unit. Press [SCREEN MODE ] repeatedly to switch the TV aspect ratio.
PTIONAL SETTING Channel Add/Delete The channel add/delete function lets you add the channel that was not added by the auto channel scan due to the reception status at the initial setting. You can also delete the unnecessary channels. Press [SETUP] to display the main menu. Use [Cursor K / L] to select “CHANNEL SETUP”, then press [ENTER].
PTIONAL SETTING Picture Adjustment You can adjust brightness, contrast, color, tint and sharpness. Press [SETUP] to display the main menu. Use [Cursor K / L] to select “PICTURE”, then press [ENTER]. e.g.) digital TV mode - TV SETUP - PICTURE CHANNEL SETUP V-CHIP SETUP LANGUAGE...
Press [SETUP] to exit. Note: • To show the closed caption on your TV screen, broadcast signal must contain the closed caption data. • Not all TV programs and commercials have the closed caption or all types of the closed caption. •...
PTIONAL SETTING DTVCC Style You can change the style of DTV CC such as font, color or size, etc. Press [SETUP] to display the main menu. Use [Cursor K / L] to select “DTVCC“, then press [ENTER]. e.g.) digital TV mode - TV SETUP - PICTURE CHANNEL SETUP...
Back Light Setting You can set the desired brightness mode. Press [SETUP] to display the main menu. Use [Cursor K / L] to select “BACK LIGHT”, then press [ENTER] repeatedly to change the setting. e.g.) digital TV mode - TV SETUP - PICTURE CHANNEL SETUP V-CHIP SETUP...
PTIONAL SETTING V-chip V-chip reads the ratings for programs, then denies access to the programs which exceed the rating level you set. With this function, you can block certain programming inappropriate for children. Press [SETUP] to display the main menu. Use [Cursor K / L] to select “V-CHIP SETUP“, then press [ENTER].
Page 23
[To Set the Sub Ratings] As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further set the sub ratings to block specific elements of programming. To set the sub ratings, follow the steps below. Use [Cursor K / L ] to select the desired main rating, then press [ENTER] twice to show its sub ratings.
PTIONAL SETTING C. Change Password C. Change Password Although the default code “0000” is supplied with the unit, you can set your own password. Use [Cursor K / L] to select “CHANGE PASSWORD”, then press [ENTER]. e.g.) digital TV mode - V - CHIP SETUP - TV RATING MPAA RATING...
ROUBLESHOOTING Troubleshooting Guide If the unit does not perform properly when operated as instructed in this owner's manual, check the following chart once before calling for service. Symptom Remedy No power • Be sure the power cord is plugged in. •...
ROUBLESHOOTING Symptom The entered channel number changes automatically Remote control does not work Misspelled captions are displayed. Captions are not entirely displayed, or captions are delayed behind the dialogue. Captions are displayed as a white box. No caption is displayed in the closed caption-supported program.
NFORMATION Glossary ATSC Acronym that stands for Advanced Television Systems Committee and the name of the digital broadcasting standards. Aspect Ratio The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the TV screen is almost square); widescreen models are 16:9 (the TV screen is almost twice as wide as its height).
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase.
Page 29
EMERSON Y EL LOGOTIPO G-CLEF SON MARCAS REGISTRADAS DE EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, EE.UU. HIGH-DEFINITION TELEVISION PARA RECIBIR LA SEÑAL DIGITAL/ ANALÓGICA, DEBE CONECTAR LA ANTENA. SI NECESITA AYUDA ADICIONAL CON LA INSTALACIÓN O CON EL FUNCIONAMIENTO DESPUÉS DE LEER EL MANUAL DEL USUARIO, LLAME AL TELÉFONO GRATUITO 1-800-256-2487 O...
NTRODUCCIÓN ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE APARATO A LLUVIA O HUMEDAD. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CUIDADO: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PLACA TRASERA). EL INTERIOR DE ESTE APARATO NO CONTIENE PIEZAS REPARABLES POR EL USUARIO.
Page 31
REPARACIÓN - No intente reparar usted mismo este televisor, ya que el hecho de abrir o extraer las cubiertas puede exponerle a tensión peligrosa u otros riesgos. Deje toda reparación en manos de personal de servicio técnico cualifi cado. DAÑOS QUE EXIGEN UNA REPARACIÓN - Desenchufe este televisor de la toma de pared y llévelo a un servicio de reparación cualifi cado en las situaciones siguientes: a.
NTRODUCCIÓN El número de serie de este producto puede encontrarse en la parte trasera de la unidad. Ningún otro producto tiene el mismo número de serie que el suyo. Debe anotar aquí el número y otros datos esenciales y conservar este libro como registro permanente de su compra con el fin de ayudar a su identificación en caso de robo.
Características • DTV/TV/CATV - Puede utilizar su mando a distancia para seleccionar canales emitidos en formato digital y formato analógico convencional. Además, los suscriptores de cable pueden acceder a sus canales de televisión por cable. • Visualización de Información (solamente DTV) - Puede visualizar el título, el contenido y otra información del actual programa DTV en la pantalla del televisor.
NTRODUCCIÓN Función de Mando a Distancia Instalación de las Pilas Instale las pilas (AA x 2) de manera que coincida la polaridad indicada en el interior del compartimento de las pilas del mando a distancia. Precauciones Sobre las Pilas: • Asegúrese de seguir la polaridad correcta según lo indicado en el compartimento de las pilas. Unas pilas en posición invertida pueden causar daños en el dispositivo.
Función de Mando a Distancia Panel de Control Panel Trasero parte trasera de la unidad parte lado de la unidad VIDEO 2 COMPONENT AUDIO VIDEO 1 AUDIO S-VIDEO VIDEO COAXIAL 1. Botón POWER (p. 11) Presione para activar y desactivar la unidad. 2.
ONEXIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. Conexión Básica En esta sección se describe cómo conectar la unidad a una antena, caja de cable/satélite, etc. Nota: • Asegúrese de que su antena u otra dispositivo está conectada correctamente antes de enchufar el cable de alimentación. [Conexión de Cable de Antena] Cuando conecte la unidad a una antena o una empresa de televisión por cable (sin caja de cable/satélite) Conecte el cable coaxial RF de su toma de corriente a la toma de entrada de antena de esta unidad.
Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. Conexión de Dispositivo Externo [Conexión de Cable de Vídeo en Componentes] La conexión de vídeo en componentes ofrece una mejor calidad de imagen para dispositivos de vídeo conectados a la unidad.
Page 38
ONEXIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. [Conexión de Vídeo] La conexión de vídeo ofrece una calidad normal de imagen para dispositivos de vídeo conectados a la unidad. Si se conecta a la toma de entrada de vídeo de la unidad, conecte cables RCA de audio a las tomas de audio L/R (izquierda/derecha) de VIDEO1.
JUSTE INICIAL Se puede acceder a estas operaciones mediante el mando a distancia. Algunas también pueden ser accesibles mediante los mandos de la unidad principal. Configuración Inicial Esta sección le guiará a través del ajuste inicial de la unidad, que incluye la selección de un idioma para sus menús de pantalla y “PREA.
JUSTE INICIAL • LUZ DE FONDO Puede ajustar el modo de brillo deseado. (Consulte “Ajuste de Luz de Fondo” en página 21.) • TENPE. DE COLOR Puede ajustar la temperatura de color (“NORMAL”, “CALIENTE”, “FRÍO”). (Consulte “Temperatura de Color” en página 21.) •...
ARA VER LA TELEVISIÓN Selección de Canal Seleccione los canales utilizando [CH. K / L] o [los botones numéricos]. • Para seleccionar los canales memorizados, utilice [CH. K / L] o [los botones numéricos]. • Para seleccionar los canales no memorizados, utilice [los botones numéricos].
ARA VER LA TELEVISIÓN Para Cambiar el Modo de Audio En esta sección se describe cómo cambiar el audio en el modo analógico y cómo cambiar el idioma de audio en el modo digital. Durante la recepción de una emisión MTS, presione [AUDIO ] repetidamente para recorrer los canales de audio disponibles.
Información de Pantalla Puede visualizar el canal actualmente seleccionado u otra información, por ejemplo el modo de audio, en la pantalla del televisor. En el modo analógico se visualiza el número del canal actual. Presione [DISPLAY ]. • Se muestra el número del canal actual en la esquina superior derecha de la pantalla del televisor.
ARA VER LA TELEVISIÓN Modo de Visualización de Pantalla del Televisor Los modos de visualización del tipo 3-5 pueden seleccionarse cuando la cadena de emisora envía una señal de vídeo 4:3 o 16:9 o cuando un dispositivo externo está conectado a la unidad. Presione [SCREEN MODE ] repetidamente para cambiar la relación del aspecto del televisor.
JUSTE OPCIONAL Agregar/Borrar Canales La función de agregar/borrar canales le permite agregar el canal que no se haya agregar mediante la exploración automática de canales debido al estado de la recepción en el ajuste inicial. También puede eliminar los canales innecesarios. Presione [SETUP] para visualizar el menú...
JUSTE OPCIONAL Ajuste de Imagen Puede ajustar el brillo, el contraste, el color, el matiz y la nitidez. Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “IMAGEN”, y luego presione [ENTER]. p. ej.) modo TV digital - INSTALACIÓN TV - IMAGEN AJUSTE DE CANAL...
Presione [SETUP] para salir. Nota: • Para mostrar los subtítulos en la pantalla de su televisor, la señal de emisión debe contener los datos de los subtítulos. • No todos los programas y anuncios de TV contienen subtítulos o todo tipo de subtítulos. •...
JUSTE OPCIONAL Estilo DTVCC Puede cambiar el estilo de DTV CC, por ejemplo fuente, color o tamaño, etc. Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “DTVCC” y luego presione [ENTER]. p. ej.) modo TV digital - INSTALACIÓN TV - IMAGEN AJUSTE DE CANAL...
Ajuste de Luz de Fondo Puede ajustar el modo de brillo deseado. Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “LUZ DE FONDO”, y luego presione [ENTER] repetidamente para cambiar el ajuste. p. ej.) modo TV digital - INSTALACIÓN TV - IMAGEN AJUSTE DE CANAL...
JUSTE OPCIONAL V-chip V-chip lee las clases de los programas, y niega el acceso a los programas que exceden el nivel de clasifi cación establecido. Con esta función, puede bloquear determinados programas inapropiados para niños. Presione [SETUP] para visualizar el menú principal. Utilice [Cursor K / L] para seleccionar “AJUSTE DE V-CHIP”, y luego presione [ENTER].
Page 51
[Para Ajustar las Subcategorías] En lo referente a TV-Y7, TV-PG, TV-14 ó TV-MA, puede seguir ajustando las subcategorías para bloquear elementos específicos de la programación. Para ajustar las subcategorías, siga los pasos indicados. Utilice [Cursor K / L ] para seleccionar la clasificación principal deseada y luego presione [ENTER] dos veces para mostrar sus subcategorías.
Page 52
JUSTE OPCIONAL C. Cambiar Contraseña Aunque el código predeterminado “0000” viene incorporado con la unidad, usted puede ajustar su propia contraseña. Utilice [Cursor K / L] para seleccionar “CAMBIAR CÓDIGO” y luego presione [ENTER]. p. ej.) modo TV digital - AJUSTE DE V-CHIP - CLASE DE TV CLASE DE MPAA CLASE DESCARGADA...
OLUCIÓN DE PROBLEMAS Guía de Solución de Problemas Si la unidad no funciona correctamente cuando se siguen las instrucciones de este manual del usuario, compruebe la siguiente tabla antes de llamar al servicio técnico. Síntoma Solución No hay corriente • Asegúrese de que el cable de alimentación está enchufado. •...
OLUCIÓN DE PROBLEMAS Síntoma El número de canal introducido • Muchos canales digitales tienen números de canal alternativos. La unidad cambia dichos cambia automáticamente El mando a distancia no funciona • Compruebe la conexión de antena o de cable con la unidad principal. •...
NFORMACIÓN Glosario ATSC Acrónimo de “Advanced Television Systems Committee” (Comité de sistemas avanzados de televisión) y el nombre de unas normas de emisión digital. Contraseña Un número almacenado de 4 dígitos que permite el acceso a las funciones de control parental.
Page 56
FUNAI CORP. reparará este producto, de forma gratuita en Estados Unidos, en caso de defecto de materiales o fabricación, del modo siguiente: DURACIÓN: PIEZAS: FUNAI CORP. suministrará piezas de repuesto de las piezas defectuosas de forma gratuita durante un (1) año desde la fecha de compra minorista original. Determinadas piezas y el efecto de persistencia de la imagen en la pantalla LCD están excluidas de esta garantía.