Table of Contents
Advertisement
4-01
4-02
4-03
4-04
4-05
Secure Aux Output (1 and 2 Only)
4-06
Auxiliary Input 1 – Green CN
4-07
Auxiliary Input 2 – Green CN
4-08
Extended Accessory After Ign Shutoff
4-09
Key Sense or Glow Plug input
Trigger Start or Closed Loop
4-10
1
2
3
4
5
6
7
8
Programmable Output Connector
1
2
3
4
5
6
7
8
9
Common Option Menu Descriptions
1-01 Unlock before, Lock after remote starting - Doors will unlock to remote start and then relock once started. This is to disarm factory alarms on certain vehicles.
1-03 Driver's priority unlock - The driver's door must be isolated from the other doors. Use the Orange/Black CN4 as your negative 2
1-04 Double pulse unlock - Sends two negative (-) pulses on the blue unlock wire.
1-06 Reservation Lock (Manual Transmission) - Setting 1 allows the doors to lock when setting reservation. Setting 2 does NOT allow the doors to lock when setting reservation.
Setting 3 gives 10 seconds before setting reservation mode after closing the last door to allow the user to open another door.
1-09 Ignition controlled door locks – Default setting locks doors when foot on foot brake. Unlocks doors when key turned off or when e-brake set on manual transmissions. Tach or
alternator sensing mode must be used for this feature. You must also turn this feature on through the remote by tapping I + IV (2 Way remotes) or Lock + Key (1 Way remotes)
2-01 Tach Sensing Method – This option changes the method which is used to read tach on different vehicles. It adjusts for situations when there may be over cranking when remote
starting. This option can also be adjusted based on option 2-12 – Crank Time. Please see tech update from April 2008 on
2-02 Turbo Timer - The e-brake must be connected to the control module. Available times are 1, 2, and 3 minutes. You must also turn on this feature through the remote by tapping
buttons III + IV.
2-03 Diesel Timer - Without setting this option you must find the vehicle's wait to start wire. The default time for Setting 2 is 10 seconds. This can be increased or decreased only
with the Option Programmer OP500.
2-04 Trigger start - This option allows the control module to be used as a slave unit. This option determines whether the slave start wire on CN3 requires a single or double pulse to
activate the remote start. This can be used on vehicles where the user would like to keep the factory remote.
Feature
Default Setting - I
Aux 1 output
Aux 2 output
Aux 1 output Control
By Remote
Aux 2 output Control
By Remote
Glow Plug Input
Trigger Start input
Alarm Trigger Input
Feature
Diesel timer - DISL
AUX1 output time
AUX2 output time
AUX3 output time
AUX4 output time
AUX5 output time
AUX6 output time
AUX7 output time
Feature
0 - Default Setting
(-) 2nd Parking Light
POC #1
(Green/White)
POC #2
(-) 2nd Start (Red/Black)
POC #3
(-) 2nd Ignition (Green)
(-) 2nd Accessory
POC #4
(White/Black)
POC #5
(-) Status/GWR (Black)
POC #6
(-) Rearm Wire (Orange)
(-) Disarm Wire
POC #7
(Orange/White)
POC #8
(-) Horn (White)
POC #9
(-) Dome Light (Violet)
OPTION GROUP 4
Optional Setting - II
0.5sec
Latch
0.5sec
Latch
Arm
Arm
On
Off
Prewarn
Trigger
Trigger
Prewarn
Off
10 sec
Key Sense Input
Closed Loop
System Input
SPECIAL OPTION GROUP 1
Setting Value [seconds]
SPECIAL OPTION GROUP 2
Setting Value
2nd Light - [1] 2nd Start - [2]
2nd Acc - [4] Status Out - [5] Rearm Out - [6]
Disarm Out - [7] Horn Out - [8] Dome Light - [9]
Aux1 Out - [10] Aux2 Out - [11] Defrost - [17]
GWA - [18] Status 2 For Manual Trans. - [19]
Optional Setting - III
Optional Setting - IV
20 sec
60 sec
Disarm
Disarm
(-)Disarm
(-)Arm
Until Door Open
30 sec
(1 min max)
3 ~ 99
1 ~ 100
1 ~ 100
1 ~ 100
1 ~ 100
1 ~ 100
1 ~ 100
1 ~ 100
1~19 – Optional Settings
2nd Ignition - [3]
nd
Unlock output.
www.compustar.com
for more info.
Program
Program
Panic
Panic
Advertisement
Table of Contents
