Table of Contents
Advertisement
Sound Indicator
This is a stereo option. The alternatives of the indicator are
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. "I-II"
button is used to select Mono or Stereo, or Dual I or Dual II.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual I is selected in default and also
can be selected after Dual II by Remote Control.
If Dual II selected by Remote Control.
Picture Mode
If your TV has the WSS feature, the picture mode OSD is dis-
played below the sound indicator, by TV Status OSD's. Accord-
ing to the WSS data, inside of the OSD box "4:3" or "16:9" or
"Auto" is written.
By pressing "
" (TXT_UPDATE) button (if Teletext is not ac-
tive) the picture mode can be switched into 4:3, 16:9 or Auto
Mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it
after 3 seconds.
If there is only one minute of the countdown left of the timer, it
is displayed automatically on the upper left of the screen, and
stayed there until finishing. Then TV goes automatically to
stand-by.
Mute Indicator
It is placed in the upper middle of the screen when enabled,
and it stays there until it is disabled.
To cancel mute, there are two alternatives.; the first one is
pressing " " button, thus volume is set to the preceding value,
and the second one is increasing the volume level, thus it
starts at the minimum level to increase. By decreasing the vol-
ume level in mute state, mute will not be ignored, only the
volume level will decrease. If mute is cancelled after decreas-
ing the volume level, the volume will set to the decreased level.
No-Signal
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid sig-
nal detected. It shows the the time remaining before switch-
ing to Stand-By mode (it takes 5 minutes when any signal de-
tected or no any Remote Control command is accessed). The
indicator is displayed in 3 seconds when there is no valid
signal.
After an Remote Control command (if No-Signal Timer is
active) the timer stops and if no signal detected again the timer
is initialized to 5 minutes and starts 3 seconds later again to
count down.
It is not valid in AV mode.
Blue Background During No-Signal
In case, no valid signal is detected (AV mode) Blue Background
is activated. During search process Blue Background is not
active. But instead of it there is another feature given; the semi-
transparent menu background is made blue.
Volume Bar
It is displayed in the lower middle of the screen. When a vol-
ume command is received (pressing "Vol+" or "Vol-" by Re-
mote Control or Front panel) and no menu is active, it stays on
the screen for 3 seconds, after the last volume command or
until another command is received in between.
AV Modes
By pressing the "
modes(except when in Teletext). Pressing this button con-
secutively will switch the TV in one off the AV modes: AV-1,
F-AV,RGB.
AV-1 supports the RGB mode. But if there is some colour prob-
lem in AV-1 mode, please force the AV mode to RGB mode.
In order to quit the AV mode press the "
Teletext
Teletext is an information system that displays text on your TV
screen. Using the Teletext information system you can view a
page of information on a subject that is available in the list of
contents (index).
On screen display is not available in text mode.
Contrast, brightness or colour control is not available, but
volume control is available in text mode.
To operate Teletext
• Select a TV station on which Teletext is being transmitted.
• Press (TELETEXT) "
(index) is displayed on the screen.
To select a page of Teletext
• Press the appropriate digit buttons for the required Teletext
page number.
The selected page number is displayed at the top left corner
of the screen. The Teletext page counter searches until the
selected page number is located, so that the desired page is
displayed on the screen.
• Press " " button to move the Teletext screen forward one
page at a time.
• Press " " button to move the Teletext screen backward one
page at a time.
GB - 13 -
ÿþ
" button you can switch your TV to AV
þÿ
" button. Usually the list of contents
" button.
Advertisement
Table of Contents
