Important Instructions; Troubleshooting Chart; Warranty - Cadet The Com-Pak Bath Heater CB103T Owner's Manual

WARNING
Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel
board door to prevent someone from turning on power while you are working on the heater. Failure to do so could
result in serious electrical shock, burns, or possible death.
CONSULT LOCAL ELECTRICAL CODES TO DETERMINE WHAT WORK MUST BE PERFORMED BY QUALIFIED ELECTRICAL SERVICE PERSONNEL.
Symptom Problem
Breaker trips immediately 1.Incorrect supply voltage.
upon energizing heater. 2.Overloaded circuit.
3.A short circuit exists in the supply
or heater wiring.
4.Defective circuit breaker.
Heater fan operates, 1.Insufficient element temperature.
but does not discharge 2.Incorrect supply voltage.
warm air. 3.Element has failed.
Heater will not shut off. 1.Heat loss from room is greater
than heater capacity.
2.Thermostat is not functioning
properly.
Heater discharges smoke 1.Dust, lint or other matter has
or emits a burnt odor. accumulated inside heater.
Element heats for a moment 1.Defective motor or internal connection.
without the fan turning, then 2.Fan or motor jammed.
immediately stops heating.
Heater does not run. 1.Thermostat is set too low, or
in disabled (no heat) position.
2.Heater has tripped the manual
high-temperature reset switch.
3.Power not on at the circuit breaker.
4.Broken or poorly connected wire(s)
to heater.
5.Defective thermostat and/or timer.
Heater continually trips 1. Dust, lint or other matter has
the manual reset accumulated inside heater.
temperature limit control. 2. Airflow is blocked.
3. Fan or motor is jammed.
4. None of the above.
LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet
product, including thermostats, found to be defective within one year after
the date of purchase.
Extended Product Warranty
LIMITED THREE-YEAR WARRANTY: Cadet will repair or replace any Com-Pak
Bathroom Heater (CB) series element or motor found to be defective or
malfunctioning from first date of purchase through the third year.
These warranties do not apply:
1. Damage occurs to the product through improper installation or incorrect
supply voltage;
2. Damage occurs to the product through improper maintenance, misuse,
abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet;
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. CADET'S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET
OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS
PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR
INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN
WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.
7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET
PRODUCT, THE REPLACEMENT PARTS ARE SUBJEC T TO THE SAME

IMPORTANT INSTRUCTIONS

Troubleshooting Chart

Solution
1. Verify that supply voltage matches the heater rating.
2. The total amperage of all heaters on a branch circuit must not be more than
80% of the amperage rating of the circuit breaker and supply wire ratings.
Use a lower wattage heater, or reduce the number of heaters on the circuit.
3. Shorted supply or heater wires may be accompanied by severe sparking. Inspect
all supply and heater wiring insulation for damage. Do not reset the circuit breaker
until all electrical shorts have been repaired.
4. Replace the circuit breaker.
1. Allow a few moments for element to reach operating temperature.
2. Verify that supply voltage matches the heater rating.
3. Replace element.
1. Close doors and windows. Provide additional insulation, or install a higher wattage
heater or multiple heaters if necessary. (If your circ uit is rated for more capacity.)
2. Wait for the timer to time-out or turn the timer counterclockwise to `0' (The timer
overrides the thermostat setting). If heater continues to run, adjust thermostat
to its lowest setting. If heater continues to run (allow two minutes for thermostat
to respond) the thermostat requires replacement.
1. Clean heater (See "Operation & Maintenance" section for instruction s).
1. Heater or fan motor requires replacement.
2. Remove obstruction and press heater reset button (after allowing the unit to cool).
Test heater operation--if reset button has been pressed (be sure to listen and feel
for a click indicating it has been reset), but heater does not run, heater requires
repair or replacement.
1. Adjust thermostat to a higher temperature until heater operates (See Problem #5
if the problem persists).
2. Press the manual reset button (See "Operation & Maintenance" section for
instructions).
3. Turn on the correct circuit breaker in the main panel.
4. Turn off power at circuit breaker. Check supply wire continuity and proper connection
to heater wires.
5. Repair or replace the heater. The entire heater, or any of its components may be
checked for continuity to determine the cause of any problem.
1. Clean heater (See "Operation & Maintenance" section for instructions).
2. Remove obstruction. Maintain a minimum distance of 6 inches from adjacent
surfaces, 4.5 inches from the floor, and 3 feet for furniture or other objects
placed directly in front of the heater.
3. Remove obstruction, and press heater manual reset button (See "Operation &
Maintenance" section for instructions) .
4. Replace heater assembly .

Warranty

8. These warranties give you specific legal rights, and you may also have
authorizes anyone to assume for it, any other obligation or liability in
If you believe your Cadet product is defective, please contact Cadet
Manufacturing Co. at 360-693-2505, during the warranty period, for
instructions on how to have the repair or replacement processed. Warranty
claims made after the warranty period has expired will be denied. Products
returned without authorization will be refused.
Parts and Service
Visit http://support.cadetco.com for information on where to obtain parts
and service.
©2009 Cadet Manufacturing Co.
WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT
PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING WARRANTIES.
REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT
CREATE ANY NEW WARRANTIES.
other rights which vary from state to state. Cadet neither assumes, nor
connection with its products other than as set out herein.
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials. You can
reduce your carbon footprint by recycling this product at the end of
its useful life. Contact your local recycling support center for further
recycling instructions.
Printed in U.S.A. Rev. 7/11 #720050
5