Page 2
(12) months from date of shipment unless specified otherwise. Batteries have no warranty. Campbell Scientific, Inc.'s obligation under this warranty is limited to repairing or replacing (at Campbell Scientific, Inc.'s option) defective products. The customer shall assume all costs of removing, reinstalling, and shipping defective products to Campbell Scientific, Inc.
CC640 Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks tab for links to specific sections. 1. Specifications ..............1 2. Introduction..............2 2.1 Connecting....................2 2.1.1 Standalone Mode................3 2.1.2 Power and Pulse Connections ............3 2.1.3 Datalogger and MD485 Multiplexer Connections ......3 2.2 Configuring....................4 2.3 Operating ....................4...
Page 4
CC640 Table of Contents 7. Image Quality .............20 7.1 Lighting Conditions ................20 7.2 Night Time Images................. 20 7.3 Date and Time Stamp................20 7.4 JPEG Compression ................21 8. Lens................22 8.1 Focus and Zoom Adjustment ..............22 8.1.1 Temperature Variations and Focus..........23 8.2 Lens Filter ....................
Page 5
CC640 Table of Contents 14. Remote Image Retrieval ..........32 14.1 LNCMD.EXE ..................32 14.2 Using LoggerNet File Control ..............33 14.3 Task Setup / LNCMD.EXE ..............34 15. Installation..............36 15.1 Enclosures.....................36 15.2 Camera Mounting Holes...............38 15.3 Enclosure Mounting Kit ...............39 Appendices A. Quick Start ............... A-1 B.
Page 6
CC640 Table of Contents Tables 1a. Configuration Cable Connections ............3 1b. CABLE3CBL Connections..............3 2. LED Information at a Glance..............8 3. Camera to Datalogger RS-232 Port using #19504........11 4. Camera RS-232 to Datalogger Com Port Connection ......12 5.
CC640 Digital Camera 1. Specifications Power Supply Operating: 9-15 VDC 250 mA Max Quiescent: 250 uA typical Operating Temperature -40°C to +70°C Ext. Input Signal Logic Low Level: 0 - 0.7 VDC (-12VDC Absolute Min) Logic High Level: 4 – 15 VDC (15VDC Absolute Max) RS-485 Max.
CC640 Digital Camera 2. Introduction The CC640 digital camera was designed to meet the stringent operational requirements necessary for remote battery powered installations. The CC640 has a very low quiescent power draw and can operate over a wide temperature range. The camera contains a CompactFlash memory card interface that turns the camera into a powerful image logger.
If the distance between the camera and datalogger will be less than 25 ft (7.6 m), the camera typically connects to the datalogger via the COMCBL1-L cable. Campbell Scientific recommends using the MD485 multiplexer if the distance between the camera and datalogger needs to be more than 25 ft (7.6 m).
2.5 Additional Reference Material The CC640 Operating Manual is intended for use by those experienced in working with Campbell Scientific dataloggers. For further information regarding the various uses and applications of the CR800, CR850, CR1000, CR3000, CR510PB, CR10XPB, CR23XPB, MD485, or any additional technology listed in this manual, refer to the appropriate Operating Manuals of these products.
CC640 Digital Camera • Use the Device Configuration Utility to change settings in the camera and other PakBus devices. Datalogger parameters can also be incorporated into the datalogger program or changed with a keyboard display. • Verify that the lens cable is properly seated, as the connector may inadvertently become unplugged during handling or installation.
CC640 Digital Camera 3.2 Power Switch The power switch can be used to power the camera continuously on or to place the camera in Auto power mode. The switch should not be left in the On position under normal operation. Leaving the switch in the On position will prevent the camera from entering its low power quiescent mode of operation.
3.6 External I/O Connector The External I/O connector provides inputs and outputs for operating camera peripherals. Please contact a Campbell Scientific sales representative for details and availability of the CC640 peripherals. The Ext. (External Control) input signal can be used to initiate an image acquisition.
The CompactFlash card is also used to provide a means of updating the camera’s embedded firmware. This is done by downloading the appropriate files from any Campbell Scientific website, renaming the new firmware hex file as “NEWCODE.HEX” (all upper case), and placing it in the root directory of the CompactFlash memory card.
CC640 Digital Camera remove the memory card, and delete the “NEWCODE.HEX” file using a PC if no other cameras need to be updated. Leaving the file on the memory card will cause the camera to repeatedly update its firmware every time the camera wakes up from its quiescent mode.
CC640 Digital Camera FIGURE 3. Insert and Align the Screwdriver to Open the Contact The screwdriver supplied with the camera is used with the #19504. Align the screwdriver by lightly inserting it in the square opening and at the angle shown. This also points to the round hole paired with that square hole.
CC640 Digital Camera FIGURE 5. Remove the Screwdriver When the screwdriver is removed, the contact closes holding the wire in place. 4.3 RS-232 Port The RS-232 port provides an RS-232 communication port for transmitting image files to a datalogger using the PakBus Protocol, and configuring the camera.
CC640 Digital Camera Logger Connection COMCBL1-L 19504 17988 Camera Connection C1947 FIGURE 6. Camera RS-232 to RS-232 Port Connection It’s also possible to use RS-232 protocol via the control ports of CR800, CR1000 and CR3000 loggers. The connection is listed below. TABLE 4.
4.4 CS I/O Port The CS I/O port on the camera provides a connector for CS I/O communication. The port is designed to communicate with Campbell Scientific dataloggers equipped with CS I/O communication ports. A ribbon cable assembly (C1947) is used to provide a male 9-pin connector that can plug directly to the CS I/O port or to an SC-12 cable that connects to the CS I/O port.
CC640 Digital Camera TABLE 5. Camera CS/IO Port to Logger CS/IO Port Connection Using #19504 CS/IO connection 9 pin to 9 pin COMCBL1-L 17855 Camera data cable junction terminals Logger CS/IO port C1947----- COMCBL1- 19504 contact kit--- 17855 (SC110) Logger Connection 17855 COMCBL1-L 19504...
CC640 Digital Camera 4.5 RS-485 Port The RS-485 terminals can be used in conjunction with the MD485 to interface a datalogger to the camera over distances of up to 4000 feet. The +12V GND and EXT control lines cannot be practically run these long distances. Normally the RS-485A and RS-485B lines, and an additional ground connection, are run these distances.
Options: 1 – 4094 Address Write This is the PakBus address of the destination device where the image files will be transmitted. The device is normally a Campbell Scientific datalogger. Extra Communication Read/ Options: 0 – 10 Seconds Delay Write Additional Delays can be added for PakBus networks with long propagation delays.
Page 24
CC640 Digital Camera Motorized Enclosure Read/ Options: Disable, Enable Disable Write Select enable if the ENC-CC motorized covered enclosure is used. It is important to select disable if the motorized enclosure is not used. Selecting enable when a motorized enclosure is not present will slow down the operation of the camera.
CC640 Digital Camera Month Read/ Options: Jan - Dec Write Date Read/ Options: 1-31 Write Weekday Read/ Options: Sun. – Sat. Write Hour Read/ Options: 0 – 23 Write In 24 Hour Format Only Minute Read/ Options: 0-59 Write Second Read/ Options: 0-59 Write...
CC640 Digital Camera 6.2 External Trigger Mode An image acquisition can also be triggered from the Ext. Input Signal on the camera. It is recommended that a short pulse be used to initiate the image acquisition. If a positive voltage is applied and not removed before the image acquisition sequence is complete, the camera will begin another image acquisition immediately after.
CC640 Digital Camera The banner ends with the internal camera temperature displayed in degrees Kelvin. This is intended for diagnostic purposes. The temperature is displayed in degrees Kelvin so that there is no confusion that the temperature represents some ambient temperature. The temperature is internal and can vary substantially from the actual ambient temperature.
CC640 Digital Camera compression will produce the smallest files but with the most degradation of the image. Small files may be important for slow telecommunication links or for applications that require a large number of pictures to be stored onto the memory card.
CC640 Digital Camera camera into the field by using an object that is at a similar distance away. It is much easier to use a larger monitor in an office environment, rather than a portable TV at the installation site, as sunlight tends to make it difficult to view a television screen outdoors.
CC640 Digital Camera 9.1 Lithium Battery The Camera is equipped with a Lithium Thionyl Chloride Battery. The battery maintains the clock functionality for periods when power is not connected to the camera. The expected battery life is 2 years. If the camera is in operation and connected to a power supply, the battery life may be extended up to 10 Years.
• Set the parameter PakBus Port to None 10.2.2 CS I/O Communication The camera can download images to a compatible Campbell Scientific datalogger via the CS I/O port. The following items are required for CS I/O PakBus communication: •...
CC640 Digital Camera • Set the parameter PakBus Destination Address to the device that is intended to retrieve the images. • Set the RS-232 BAUD rate to match the BAUD rate of the device being connected to the camera. Refer to Section 3 for additional information and connections diagrams using the RS-232 port.
CC640 Digital Camera 11.1 Standalone Operation In standalone mode the camera operates as a self-contained image logger. The current draw of the camera while in low power quiescent mode is 250uA. When the camera wakes up to take a picture, operating current draw increases to a maximum of 250 mA for approximately 30 seconds.
CC640 Digital Camera The following table is a guideline for determining the amount of time it takes to transfer an image using RS-232 communication. TABLE 8. RS-232 Port File Transfer Times and Power Usage per Image RS-232 Very High High Medium None Lossless Communication...
CC640 Digital Camera 12. Interface Guide for the CR800, CR850, CR1000, or CR3000 This section contains information for interfacing the CC640 camera to the CR800, CR850, CR1000, or CR3000 datalogger. The datalogger and the CC640 both have several different types of communication ports. This provides different interface options for the user.
CC640 Digital Camera drive (memory card) this can be larger. When communications are used to retrieve images, it is suggested to limit the number of files in the ring memory to 200 in order to avoid long communication delays. An example Files Manager setting is as follows: (55,USR:SkySouth.JPG,3) •...
CC640 Digital Camera 13. Interface Guide for CR510, CR10X, or CR23X This section contains information for interfacing the CC640 camera to a CR510, CR10X, or CR23X datalogger. The CC640 camera can interface to the datalogger via the CS I/O port directly or through an MD485 interface. 13.1 Datalogger Requirements The datalogger needs to be a 2 MB datalogger.
CC640 Digital Camera • *D 13:00 • 15A 15:???? – PakBus Address (prefer 1) must match the destination PakBus address of the camera setting. • 01:0000 –The Max number of Nodes recommend 3 or more • 02:0000 –The Max number of neighbours recommend 3 or more. •...
CC640 Digital Camera • Delete-File <Station> <Filename> Deletes a file stored in the datalogger. This is currently not supported on the CR510, CR10X, or CR23X datalogger. • Retrieve-File < Station > < Filename > <Output Filename > This should be the only command required to collect images with the datalogger.
CC640 Digital Camera FIGURE 13. LoggerNet File Control Screen 14.3 Task Setup / LNCMD.EXE Automated image collection can be achieved by setting up a Task in Loggernet that executes the LNCMD.EXE executable. A sample screen of a Task setup that executes LNCMD.EXE is shown in FIGURE 14 Task Setup.
Page 41
CC640 Digital Camera FIGURE 14. Task Setup In the above example the task will execute on its own schedule separate from data collection. A task can also be created that calls the LNCMD.EXE after scheduled data is collected. This may be more desirable for stations that are called using a dial up connection to eliminate separate dialling for data and images.
CC640 Digital Camera FIGURE 15. Task using Add After to Collect Images after Scheduled Call Note that it is necessary to specify the directory in which the files are located for the CR800, CR850, CR1000, and CR3000. In our example the USR: drive is selected.
CC640 Digital Camera FIGURE 18. The Back of the 18543 Enclosure Showing the Lockable Hasp 15.2 Camera Mounting Holes For flexibility, the camera is equipped with 2 different sets of mounting holes (Figure 19). There are three ¼”-20 threaded mounting holes along the center of the camera that are spaced 2.0”...
CC640 Digital Camera 15.3 Enclosure Mounting Kit The 18549 Enclosure Mounting Kit is used to mount the 18543 camera enclosure to a CM202, CM204, or CM206 crossarm. The crossarm then attaches to a tripod, tower, or user-supplied pole (1.0” to 2.1” outer diameter). Figure 20 shows the camera enclosure mounted to a crossarm via this bracket.
Appendix A. Quick Start The quick start section describes setting up a camera to a CR800, CR850, CR1000, or CR3000 datalogger. If using a CR10X, CR510, or CR23X, please call the factory. • Configure the logger with Device Configuration. 1. Select the port to be used and select the baud rate to use. If using RS232 connected to a com port, use the following for connections: pin 3 to odd # control port, pin 2 to even # control port, pin 5 to ground.
Appendix B. DC Heater Kit The optional DC heater kit consists of the following components: 1- heater with connector attached 1- solid state relay 1- wire nut 1- field power cable FIGURE B-1. Components of the 26140 Heater Kit The solid state relay mounts in the logger enclosure. All other components are in the camera enclosure.
Appendix B. DC Heater Kit The steps for installation are 1. Attach the heater to the camera enclosure window 2. Wire the field power cable to the camera and to the camera cable 3. Connect the field power cable to the heater cable 4.
Appendix B. DC Heater Kit FIGURE B-3. Field Power Cable Connected to the Camera 10. Connect the connector from the field power cable to the camera heater connector. FIGURE B-4. Field Power Cable Connected to the Heater Connector 11. Connect terminal number 1 of the solid state relay to the heater supply wire (labeled “+”) with a user-supplied 16-AWG wire.
Appendix B. DC Heater Kit 12. Connect terminal number 2 of the solid state relay to the 12-Vdc source. Do not use the datalogger as a 12 V source. 13. Connect terminal 3 of the solid state relay to the control port on the logger that will be used to control the relay.
Page 53
Appendix C. Troubleshooting Observe the LED Operation On normal power up the LED will slowly flash 4 times. If the LED flashes rapidly for several seconds the camera failed one of the power-on tests. In this case factory repair is necessary. The LED will also flash once if the Setup button is pressed.
Page 54
Appendix C. Troubleshooting This is a blank page.
Page 55
Appendix D. Example CRBasic Program The following is a CR800 example program. The CR1000 and CR3000 are programmed similarly. 'CR800 Series 'This program allows the user to take a picture on command, time an image, or take a picture based 'on a threshold.
Page 58
Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbellsci.com Campbell Scientific Africa Pty. Ltd. (CSAf) PO Box 2450 Somerset West 7129 SOUTH AFRICA www.csafrica.co.za • cleroux@csafrica.co.za Campbell Scientific Australia Pty. Ltd. (CSA)