Download Print this page

Parasound D/AC-2000 Owner's Manual

Ultra digital to analog converter

Advertisement

Quick Links

O
W
N
Congratulations on the purchase of this precision audio component and thank you for your selection of
Parasound. Your new D/AC-2000 features a state-of-the-art 20 bit D20400A dual digital to analog
converter and custom AES 21 digital interface receiver designed and manufactured by UltraAnalog, Inc. The
D/AC-2000 also incorporates the High Definition Compatible Digital PMD-100 HDCD process decoder
developed by Pacific Microsonics. This decoder performs precise decoding of HDCD encoded recordings
and also functions as a superb digital filter that will enhance the sonic quality of non-HDCD encoded
recordings.
Please take a few moments to read these instructions so you may fully understand how to maximize the
performance capabilities of your new digital to analog converter.
Unpacking and Placement
Open the carton of your D/AC-2000 carefully and inspect the unit for possible shipping damage. Report any
damage to your dealer immediately. You will find the detachable AC line cord packed separately inside the
carton.
Save your plastic bag, inserts, and carton. You may need these later for transporting the D/AC-2000 or for
shipment in the event it ever requires factory service. Record the serial number (on rear panel) here for future
reference: ____________________
Place your D/AC-2000 as close as possible to your digital source. Keep it out of direct sunlight, and away
from heat sources such as a hot air vent or radiator. If you are stacking your components, avoid placing your
D/AC-2000 on top of heat producing components, such as power amplifiers or tube-type preamplifiers.
Keep it as far away from your tuner or receiver as possible to avoid RF interference.
E
R
'
S
D/AC-2000 Ultra Digital to Analog Converter
S a m p l i n g F r e q u e n c y
S a m p l i n g F r e q u e n c y
H D C D
H D C D
P o w e r
P o w e r
4 8 k H z
4 8 k H z
3 2 k H z
3 2 k H z
4 4 . 1 k H z
4 4 . 1 k H z
M
A
D e - E m p h a s i s
D e - E m p h a s i s
S T O p t i c a l
S T O p t i c a l
P o l a r i t y
P o l a r i t y
I n v e r t
I n v e r t
-1-
N
U
A
C o a x i a l
C o a x i a l
A E S / E B U
A E S / E B U
T o s l i n k
T o s l i n k
L

Advertisement

loading

Summary of Contents for Parasound D/AC-2000

  • Page 1 Congratulations on the purchase of this precision audio component and thank you for your selection of Parasound. Your new D/AC-2000 features a state-of-the-art 20 bit D20400A dual digital to analog converter and custom AES 21 digital interface receiver designed and manufactured by UltraAnalog, Inc. The D/AC-2000 also incorporates the High Definition Compatible Digital PMD-100 HDCD process decoder developed by Pacific Microsonics.
  • Page 2 I n d i c a t o r s S w i t c h Figure #1 D/AC-2000 Front Panel Controls PARASOUND D/AC-2000 Ultra Digital to Analog Converter Parasound Products, Inc. Analog Outputs Digital Inputs San Francisco, CA. U.S.A Made in U.S.A.
  • Page 3 CD players. You should use only good quality cables which have been designed for digital data transmission such as the Stereophile recommended Parasound DataBridge. Cables designed for audio frequencies are not suitable for digital signals and will not give you satisfactory results.
  • Page 4 Analog Output Connections Analog output jacks connect to any line level input on your preamplifier or even directly to your power amplifier, provided it is equipped with level controls. Use only high-quality interconnects to preserve detail and clarity. Make sure your preamplifier is either turned off or its volume is set to minimum whenever making connections.
  • Page 5 If we determine that your D/AC-2000 requires service, we will refer you to your local Authorized Parasound Warranty Center. If you choose to return the unit to Parasound, we will give you a Return Authorization Number. You will be asked to carefully pack the unit in its original carton and cardboard packing plus an additional outer box for protection in transit.
  • Page 6 D/AC-2000 Specifications Frequency Response: DC - 20 kHz, +0/-.5 dB Signal to Noise Ratio: > 108 dB Channel Separation: > 104 dB @ 20 kHz; > 110 dB @ 1 kHz; Total Harmonic Distortion: < 0.0015% @ 1 kHz Full Scale Output <...
  • Page 7 For Returns: Contact Parasound’s Technical Services Department. If it is decided that the unit should be returned for inspection at Parasound, it must be packed in its original carton as well as an additional outer carton. An RA number will be issued which must appear on the outer carton. A note stating the nature of the defect should accompany the unit.