FCC Part 68 This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must provide this information to the telephone company upon request.
FCC Part 15 The modem generates and uses radio frequency energy. If it is not installed and used properly in strict accordance with the user's manual, it may cause interference with radio and television reception. The modem has been tested and found to comply with the limits for Class B computing devices in accordance with the specifications in Subpart B, Part 15 of the FCC regulations.
1.1 Overview The Infineon Amazon Single-Chip ADSL2+ Router is optimized to address the growing demand for high-speed Internet access, and it does so as a single, highly-integrated and cost-effective solution. 1.2 Features ADSL2/2+ Compliance C ompliant with ADSL standards ‧ Full-rate ANSI.413 Issue 2 , ITU G.dmt (G.992.1) , G.dmt bis (G.992.3) and G.adslplus(G.992.5) standards Splitter less ITU G.lite (G.992.2) specification Annex A (ADSL over POTS) and Annex B (ADSL over ISDN), compliant to ETSI TS 101 388...
Wireless Features S upport 802.11b/g Wireless MIMO Access Point ‧ ‧ S upport 128-Bit and 64-Bit WEP encryption , 802.1x, WPA, WPA2 Security S tateful packet inspection and filtering ‧ ‧ I ntrusion detection and protection P AP (password authentication protocol) ‧...
Chapter 2 Installation This chapter offers information about installing your router. If you are not familiar with the hardware or software parameters presented here, please consult your service provider for the values needed. 2.1 Checklist Check the shipping box carefully to ensure that the contents include the items you ordered. If any of the items are missing or damaged, contact your local distributor.
2.2 The Front LEDs State Description POWER When the router power on. "Showtime"-successful connection between ADSL modem and telephone company's network. ADSL Flashing "Handshaking"-modem is trying to establish a connection to telco's network Modem is powered OFF ADSL Carrier Detect if LED is flash. Flashing Data transmit between router and telco.
2.5 Hardware installation This section describes how to connect and configure the ADSL2+ Router. Step 1. Connect the ADSL Line Connect the router directly to the wall jack using the included ADSL cable. Step 2. Connect a Workstation to the Router's LAN port There are two methods to connect the router and workstation.
Page 12
Figure 2-5.2 Router Connected through several micro-filters ISDN Splitter Configuration (ADSL over ISDN) A ISDN splitter separates ADSL signals from ISDN signals on your ISDN telephone line. The ISDN splitter works by running a separate ADSL line from the ISDN line, so that the ADSL router has a dedicated cable for data transmission.
Chapter 3 Configuration 3.1 Determine your connection settings Before you configure the router; you need to know the connection information supplied by your ADSL service provider. 3.2 Connecting the ADSL Router to your network Unlike a simple hub or switch, the setup of the ADSL Router consists of more than simply plugging everything together.
Page 14
At the Password prompt, type 'admin'. You can change these later if you wish. Click 'LOGIN'.
Page 15
You can use "Quick Setup" to setup the router, and the router will connect to the Internet via ADSL line.
3.3.1 Hostname Setting Enter the host name representing your host and the domain name you want to configuration, then you can doing web configuration by typing the whole name you configuration instead by typing the IP address.
3.3.2 System Time Connecting to a Simple Network Time Protocol (SNTP) server allows the router to synchronize the system clock to the global Internet. The synchronized clock in the router is used to recorded the security log and control client filtering.
3.3.4 Firmware Update The new firmware for your router can improve functionality and performance. Enter the path and name of the upgrade file then click the APPLY button below. You will be prompted to confirm the upgrade.
3.3.6 System Reset In the event that the router stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the "Reset" button below. You will be asked to confirm your decision.
Page 26
The router can be connected to your service provider in any of the following ways Dynamic IP Address: Obtain an IP address automatically from your service provider. Static IP Address: Uses a static IP address. Your service provider gives a static IP address to access Internet services.
3.5.3 DNS A Domain Name system (DNS) server is like an index of IP addresses and Web addresses. If you type a Web address into you browser, a DNS server will find that name in its index and find the matching IP address.
3.5.4 DDNS Dynamic DNS allows you to update your dynamic IP address with one or many dynamic DNS services. So anyone can access your FTP or Web service on your computer using DNS-like address.
3.6.1 LAN Configuration The "LAN Settings" option enables you to configure the LAN port. If the DHCP Relay is selected, the DHCP requests from local PCs are forward to the DHCP server runs on WAN side. To have this function working properly, disable the NAT to run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry.
3.6.4 IGMP Setting The Internet Group Management Protocol is a communication protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships, which is important for high-bandwidth multicast groups and / or subnets with highly volatile group membership.
3.7.1 Wireless Setting SSID The identifier for the network. You can change the SSID. Only devices with the same SSID can interconnect. Channel ID The channel number used for networking. The channel setting of the wireless devices within a network should be the same.
3.8.1 Firewall Setting The router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. However, for applications that requires unrestricted access to the Internet.
3.8.2 DoS Options “Block WAN Scan” allow you to prevent the hackers from testing the services of the router. "Discard ping from WAN side" cause the router to not respond to the hacker scan packets from the public WAN IP address.
3.9.1 NAT Setting Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single public IP address or multiple public IP addresses. NAT can also prevent hacker attacks by mapping local addresses to public addresses for key services such as the Web or FTP.
3.9.2 Virtual Server You can configure the router as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses.
3.9.3 Port Mapping For some applications, you need to assign a set or a range of ports (example 4000-5000) to a specified local machine to route the packets. The router allows the user to configure the needed port mappings to suit such applications.
3.9.4 DMZ Setting If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall, you can open the client up to unrestricted two-way Internet access by defining a virtual DMZ Host.
3.10.1 Static Routing The static routing function determines the path that router follows over your network before and after it passes through your router. You can use static routing to allow different IP domain users to access the Internet through this device.
3.10.2 Dynamic Routing The dynamic routing feature of the router can be used to allow the router to automatically adjust to physical changes in the network's layout. The router uses the dynamic RIP protocol. It determines the route that the network packets take based on the fewest number of hops between the source and the destination.
3.12.1 TCP/IP Settings for Windows Operating System 1. How can I find my IP Address in Windows 95, 98, or Me? C lick on Start, then click on Run. ‧ T he Run Dialogue Box will appear. Type winipcfg in the window as shown then click OK ‧...
Page 50
2. How can I find my IP Address in Windows 2000/XP? C lick on Start and select Run. ‧ ‧ T ype cmd then click OK. ‧ F rom the Command Prompt, enter ipconfig. It will return your IP Address, subnet mask, and default gateway.
Page 51
3. How can I assign a Static IP Address in Windows 98/Me? F rom the desktop, right-click on the Network Neighborhood icon (Win ME - My Network Places) and ‧ select Properties. H ighlight TCP/IP and click the Properties button. If you have more than 1 adapter, then there will be a ‧...
Page 52
C lick Specify an IP Address. ‧ E nter in an IP Address that is on the same subnet as the LAN IP Address on your router. Example: If the ‧ router ´ s LAN IP Address is 192.168.0.1, make your IP Address 192.168.0.X where X is between 2-99. Make sure that the number you choose is not in use on the network.
Page 53
C lick on the DNS Configuration tab. ‧ C lick Enable DNS. Type in a Host (can be any word). Under DNS server search order, enter the LAN IP ‧ Address of your router (192.168.0.1). Click Add. C lick OK twice. ‧...
Page 54
4. How can I assign a Static IP Address in Windows 2000? R ight-click on My Network Places and select Properties. ‧ ‧ R ight-click on the Local Area Connection which represents your network card and select Properties. ‧ H ighlight Internet Protocol (TCP/IP) and click Properties.
Page 55
C lick Use the following IP Address and enter an IP Address that is on the same subnet as the LAN IP ‧ Address on your router. Example: If the router s LAN IP Address is 192.168.0.1, make your IP Address ´...
Appendix A Glossary Address mask A bit mask used to select bits from an Internet address for subnet addressing. The mask is 32 bits long and selects the network portion of the Internet address and one or more bits of the local portion. Sometimes called subnet mask.
Page 57
Customer Premises Equipment located in a user's premises DHCP (Dynamic Host Configuration Protocol) DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP/IP network. DHCP eliminates having to manually assign permanent IP addresses to every device on your network. DHCP software typically runs in servers and is also found in network devices such as Routers.
Page 58
HTML Hypertext Markup Language - The page-coding language for the World Wide Web. HTML browser A browser used to traverse the Internet, such as Netscape or Microsoft Internet Explorer. http Hypertext Transfer Protocol - The protocol used to carry world-wide-web (www) traffic between a www browser computer and the www server being accessed.
Page 59
Network Address Translation - A proposal for IP address reuse, where the local IP address is mapped to a globally unique address. Network Virtual Terminal Password Authentication Protocol PORT The abstraction used by Internet transport protocols to distinguish among multiple simultaneous connections to a single destination host.
Page 60
Router A system responsible for making decisions about which of several paths network (or Internet) traffic will follow. To do this, it uses a routing protocol to gain information about the network and algorithms to choose the best route based on several criteria known as "routing metrics". Routing table Information stored within a router that contains network path and status information.
Page 61
Subnet For routing purposes, IP networks can be divided into logical subnets by using a subnet mask. Values below those of the mask are valid addresses on the subnet. Transmission Control Protocol - The major transport protocol in the Internet suite of protocols provides reliable, connection-oriented full-duplex streams.
Page 62
Wide area network - A data communications network that spans any distance and is usually provided by a public carrier (such as a telephone company or service provider).
Appendix B Cabling / Connection Network cables connect PCs in an Ethernet network Category 5, called "Cat5" for short is commonly used type of network cable today. Cat 5 cables are tipped with RJ-45 connectors, which fit into RJ-45 port. Straight-through vs.
Page 64
Declaration of Conformity The following Equipment: ADSL2+ Wireless MIMO Router Report No.: S940111 is herewith confirmed to comply with the requirements set out in the Council Directive on the harmonization of the Laws of the Member States relating to electrical equipment designed for use within certain voltage limits (73/23/EEC).