Advertisement
Table of Contents
- 1 Table of Contents
- 2 Warnings
- 3 Product Specifications
- 4 Component Identification
- 5 Missing Parts Order Form
- 6 Safety Information
- 7 Operating Guidelines
- 8 Assembly
- 9 Important Engine Information
- 10 Operating Instructions
- 11 Maintenance & Storage
- 12 Troubleshooting
- 13 Limited Warranty & Service
- Download this manual
Chipper/Shredder with 2-Way Feed
®
This manual contains important safety instructions for
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS
or go to www.beastpowerequipment.com
When you call the help-line you will need to have the following information:
Date of Purchase:
Location of Purchase: _______________________
Serial #:
Model #:
Owner's Manual
Chipper/Shredder models: CH2, CH3, CH4
CAREFULLY SAVE THESE INSTRUCTIONS.
For product questions or service,
CALL 1-919-550-3259
_______________________
_______________________
_______________________
TM
Advertisement
Table of Contents
Summary of Contents for Brush Master CH2
- Page 1 Chipper/Shredder with 2-Way Feed ® Owner’s Manual This manual contains important safety instructions for Chipper/Shredder models: CH2, CH3, CH4 READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY SAVE THESE INSTRUCTIONS. For product questions or service, CALL 1-919-550-3259 or go to www.beastpowerequipment.com ...
- Page 2 No part of this publication can be reproduced or distributed without prior written permission of GXi Outdoor Power, LLC Clayton, NC 27520 USA. Brush Master™ is a trademark of GXi Outdoor Power, LLC DEK® is registered trademark of GXi Outdoor Power, LLC DEK®...
-
Page 3: Table Of Contents
Operating Guidelines ............6 Assembly ................7 Important Engine Information ..........8 Operating Instructions ............9 Maintenance & Storage ............ 10 Troubleshooting ............... 12 Limited Warranty & Service ..........13 Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 4: Warnings
Specifications table pg 2) in the side chute. Do not deflector has been installed properly. deposit branches larger than 1/4 inches into the funnel. DO NOT force the branches into this machine, allow the machine to automatically feed through. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 5: Product Specifications
Displacement (cc) 265 cc 279 cc 420 cc Walk or Pull either either either Chipper Shredder Maximum Cutting 3” x 3” 3” x 3” 3” x 4” Thickness Diameter (in.) Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 6: Component Identification
If you are missing any parts, please complete the form on the next page and fax it back to us at: 919-550-3277. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 7: Missing Parts Order Form
Comments: IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.com. If emailing, please scan in your proof of purchase. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 8: Safety Information
Tighten gasoline cap securely. h. If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area and wait 5 minutes before starting the engine. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 9: Operating Guidelines
18. Do not leave this machine running while unattended long branches such as 19. Keep children, bystanders, and pets 75 feet away. Weeping Willows as they may clog the flails. 20. Use only manufacturer approved accessories/ attachments. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 10: Assembly
Place the trailer hitch into the socket at the base of the chipper over the axle assembly. Insert the pin and secure with the locking cotter pin. 8. Re-connect the spark plug wire. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 11: Important Engine Information
Refuel in a well ventilated area with the engine stopped. Fuel vapors are extremely flammable and may ignite after the engine has started. Make sure that any spilled fuel has been wiped up before starting the engine. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 12: Operating Instructions
Pull rope with a rapid, opening. continuous, full arm stroke. Keep a firm grip on starter handle. Let the rope rewind slowly. Repeat the previous Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... - Page 13 To accomplish this, remove the pins and slide the flail screen out of the discharge chute. 5. Maintain or replace safety and instruction labels, as necessary. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed...
-
Page 14: Maintenance & Storage
Place a new belt on the pulleys in a similar fashion. To tighten the tension on the pulleys, follow the above steps plus: Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 15: Troubleshooting
Rate of discharge slows 2. Chipper blade dull. 2. Replace chipper blade or see your authorized service dealer. NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer. Rev: 07/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... -
Page 16: Limited Warranty & Service
Emission controls are covered by this warranty for all uses for a period of 3 years from original retail purchase date, this coverage extends to subsequent owners of the product with proof of original purchase. Rev: 04/2010 Brush Master™ Chipper/Shredder with 2-Way Feed... - Page 17 Turf Beast The Beast Brush Beast Brush Master Check out our other great products at www.HomeDepot.com or visit our web site at www.beastpowerequipment.com Turf Beast Turf Beast 36 in. Walk 54 in. Walk Behind Mower Behind Mower The Beast 100 in. Tow...