Brother XR1300 Quick Setup Manual

■
Operation keys and LCD
Teclas de operación y pantalla de LCD
2
1
8
9
0
A
1 LCD (liquid crystal display) 8 Sewing speed controller 1 LCD (pantalla de cristal líquido)
1 Number of the selected stitch
1 Número de la puntada seleccionada
9 Needle position button
2 Presser foot to be used 2 Pie prensatela que se va a utilizar
0 Reverse/reinforcement stitch button
3 Stitch length (mm)
3 Longitud de la puntada (mm)
A Start/stop button
4 Stitch width (mm)
4 Anchura de la puntada (mm)
2 Stitch selection keys 2 Teclas de selección de puntada
3 Stitch length adjustment key 3 Tecla de ajuste de longitud de la puntada
4 Stitch width adjustment key
4 Tecla de ajuste de anchura de la puntada
5 Mirror image stitch indicator
5 Indicador de puntada imagen en espejo
6 Utility stitch indicator 6 Indicador de puntada con aplicaciones
7 Stitch category selection key 7 Tecla de selección de la categoría de puntada
■
Selecting a stitch
Selección de una puntada
Example:
Ejemplo:
(04)
1 2
3 4
Refer to the Operation Manual for detailed instructions about sewing.
Consultar el manual de instrucciones detalladas acerca de la costura.
Preparing the bobbin thread
Preparación del hilo de la bobina
1
3
5 6 7
4
11.5 mm
(7/16 inch)
11,5 mm
(7/16 pulg.)
8 Control de velocidad manual
9 Botón de Posición de aguja
0 Botón de Costura en reversa/remate
g
A Botón de Inicio/parar
1
f
2
3
1
Turn the power on.
2
Press the stitch category selection key
as many times as necessary until the
utility stitch indicator is lit.
3
Press (stitch selection keys). The
number of the selected stitch is
displayed.
4
Attach the presser foot indicated
in the LCD.
e
2 3
2
1 9
Be sure to use the correct bobbin. Press the foot controller or press
(start/stop button) to start.
2
Press down on the spool pin lever.
0
Remove the spool cap. Winding starts. Wait until the bobbin
seems full and begins spinning slowly.
3
Fully insert the spool of thread onto
a
the spool pin. Take your foot off the foot controller or
Slide the spool cap onto the spool pin. press (start/stop button) to stop.
1
4 b
1
Pass the thread under the thread Cut the thread.
guide.
Slide the bobbin to the left and remove
2
Pass the thread under the thread the bobbin from the shaft.
guide cover.
c
3
Pull the thread to the right. Slide the sewing speed controller
Make sure that the thread passes
to the left.
under the pre-tension disk.
d
Turn the power off.
5
Align the notch to the projection.
e
Slide the bobbin to the right.
Slide the button and open the cover.
6
Wind the end of the thread. f
Insert the bobbin.
Cut the thread.
Push the bobbin down.
Pull the thread firmly around the tab.
7
Slide the sewing speed controller to
Cut the thread with the cutter.
the right.
g
Replace the bobbin cover.
8
Turn the power on.
d c b
2
4
1
Thread guide
1
2
3
4 4 4 23
_
e g 79ac
560b
a
1
2 3
Thread guide cover Pre-tension disk
5
6
9a
7
8d
8
0
9