1. Manuals
  2. Brands
  3. INSTEON Manuals
  4. Monitor
  5. Smarthome 2448A2
  6. Owner's manual

INSTEON Smarthome 2448A2 Owner's Manual

In-home energy display
Hide thumbs Also See for Smarthome 2448A2:
Table of Contents

Advertisement

Quick Links

Download this manual
Energy Display Owner's Manual
Energy Display
®
INSTEON
In-Home Display
Model :
2448A2
Page 1 of 13
2448A2 - Rev: 8/23/2011 5:22 PM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Smarthome 2448A2 and is the answer not in the manual?

Questions and answers

Related Manuals for INSTEON Smarthome 2448A2

Summary of Contents for INSTEON Smarthome 2448A2

  • Page 1 Energy Display Owner’s Manual Energy Display ® INSTEON In-Home Display Model : 2448A2 Page 1 of 13 2448A2 - Rev: 8/23/2011 5:22 PM...

  • Page 2: Table Of Contents

    ......4 HOW TO SET UP ENERGY DISPLAY TO MONITOR AN APPLIANCE’S POWER C N O SUMPTION..4 Linking Energy Display to an INSTEON Meter Device ................4 Unlinking an INSTEON Meter Device from Energy Display.........

  • Page 3: About Energy Display

    Its sleek, mpact design uses radio frequency (RF) to communicate and retrieve information from INSTEON power mete r device s (e.g., iMeter Solo, #2423A1).

  • Page 4: Installation

    POWER CONSUMPTION Linking Energy Display to an INSTEON Meter Device Follow these steps to Link Energy Display to an INSTEON meter device (e.g., iMeter Solo). See the meter device’s Owner’s Manual for detailed instructions on how to properly install and Link it to Energy Display.

  • Page 5: Using Energy Display

    Energy Display Owner’s Manual The Energy Display Status LED will begin blinking red You will have 4 minutes to complete the next step before Unlinking Mode automatically times out. Press & hold the meter device’s Set button until it beeps (3 seconds) Energy Display will double-beep and its Status LED will turn off Confirm that...
  • Page 6 Press & hold for 3 seconds to Link a meter device to the current meter position on Set button Energy Display (Meter 1, 2, or 3). See Linking Energy Display to an INSTEON Meter Device. Page 6 of 13 2448A2 - Rev: 8/23/2011 5:22 PM...

  • Page 7: Setup Modes

    Energy Display Owner’s Manual Setup Mo But on Action To enter Setup Mode, press & hold the Mode/Setup button until the cost setting field begins blinking. Then tap the Mode/Setup button to cycle to the desired settings. Mode/Setup To exit Setup Mode: ...
  • Page 8 Energy Display Owner’s Manual Temperature Format Setting NOTE: Green text indicates flashing text on the Energy Display screen. Format toggles between Celsius and Fahrenheit. The default is Fahrenheit. Button Action Hold/Up Tap to toggle the temperature display between Celsius and Fahrenheit 1-2-3/Down Tap to accept current Temperature Format setting and exit Setup Mode Refresh/OK...
  • Page 9 Energy Display Owner’s Manual Temperature Calibration Mode NOTE: Green text indicates flashing text on the Energy Display screen. The Energy Display temperature comes pre-calibrated. Only perform these steps if re-calibration is necessary. Please allow 20 minutes for temperature to adjust when moving to an area with a significant temperature change.

  • Page 10: Advanced Features Of Energy Display

    The factory reset procedure can be used to clear the Energy Display memory and restore its factory default settings. This procedure will clear Energy Display of all INSTEON Links and Sett ings Mode changes. Note: this procedure does not reset any INSTEON meter devices linked to Energy Display.

  • Page 11: Troubleshooting

    INSTEON devices. All INSTEON devices be too weak. act as INSTEON network rep eaters. If the INSTEON device is still available, Unlink it Energy Display Energy Display m ay be from Energy Display. See Unlinking an INSTEON doesn’t always...

  • Page 12: Specifications, Certification, And Warranty

    Energy Display Owner’s Manual SPECIFICATIONS, CERTIFICATION, AND WARRANTY Specifications View specifications for Energy Display at: www.smarthome.com/2448A2.html FCC & Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause undesired...
  • Page 13 For repair or replacement during the warranty pe riod, call the INSTEON Gold Support Line at 800-762-7845 with the Model # a nd Revision # of the device to receive an RMA# and send the product, along with all other required materials to: Smarthome, Inc.

Table of Contents