Remote Control; General - Insignia NS-19LD120A13 User Manual

Problem Solution
No output from one of the
• Adjust the audio balance. See
speakers.
• Make sure that the audio cables are connected
After images appear.
• Do not display a still image, such as a logo,

Remote control

Problem Solution
Remote control does not
• Make sure that the power cord is correctly
work.
• Make sure that there are no obstructions
• Point the remote control directly at the remote
• The supplied batteries are wrapped tightly in
• Make sure that the batteries are installed
• Replace dead batteries with new batteries. See
Trouble programming your
• See instructions and a table of common codes in
existing universal remote
control.
• Codes are subject to change. For up-to-date
• Replace dead batteries with new batteries. See
• Refer to the User Guide that accompanied your

General

Problem Solution
No power.
• Make sure that the power cord is correctly
• Unplug the power cord, wait 60 seconds, then
• Other devices (for example, a surround sound
44
"Adjusting sound
settings" on page 25.
correctly and securely to your TV/DVD combo.
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
connected to your TV/DVD combo and a power
outlet.
between the remote control and the remote
control sensor on the front of the TV/DVD
combo.
control sensor on your TV/DVD combo. For the
location of the remote control sensor, see
"Aiming the remote control" on page 18.
clear plastic. Make sure that you have removed
this plastic from the batteries.
correctly. See "Installing remote control
batteries" on page 18.
"Installing remote control batteries" on page 18.
"Programming a different universal remote
control" on page 47.
codes, go to
www.insigniaproducts.com/remotecodes
"Installing remote control batteries" on page 18.
universal remote control and contact the
manufacturer if problems persist.
connected to your TV/DVD combo and a power
outlet.
plug the cord back in and turn on your TV/DVD
combo.
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV/DVD combo. Try
turning off one device at a time to determine
which device is causing interference. After you
have determined which device is causing
interference, move it further from the TV/DVD
combo to eliminate the interference.
www.insigniaproducts.com
NS-19LD120A13 Insignia 19" LCD TV/DVD Combo
Problem Solution
"No signal" error
• Press INPUT and make sure that you have
message is displayed.
selected the correct input for the device or
service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
After Auto Channel
• Reception can vary by channel depending on the
Search, there are no
broadcast power level of a given station. Contact
channels.
your cable or satellite TV provider.
• Make sure the antenna or cable/satellite TV is
connected securely to your TV/DVD combo.
• Try replacing the cable between the
antenna/cable or cable/satellite box and your
TV/DVD combo.
One or more channels
• Make sure that the channels are not blocked. See
do not display.
"Setting parental control
• Make sure that the channels are not hidden. The
channel may have been deleted from the
channel list. You can tune to the channel by
pressing the number buttons or you can add the
channel back to the channel list. See
channels" on page 28.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
• If you are using an antenna, the digital channel
signal may be low. To check the digital channel
signal strength, see
strength" on page 29.
Password is lost.
• Enter 9999 to access parental controls, then set
a new password. See
password" on page 29.
Some settings cannot be
• If a setting is grayed, the setting is not available
accessed.
in the current video input mode.
TV/DVD combo cabinet
• When the TV/DVD combo is in use, the
creaks.
temperature rises naturally and may cause the
cabinet to expand or contract which can cause a
creaking noise. This is not a malfunction.
Control buttons do not
• Make sure that the Button Lock option is set to
work.
Off. See
• Unplug the power cord, wait a few seconds, then
plug the cord back in and turn on your TV/DVD
combo.
TV keeps turning off.
• Make sure that the sleep timer is not turned on.
See
levels" on page 31.
"Hiding
"Checking the digital signal
"Setting or changing the
"Locking control buttons" on page 30.
"Setting the sleep timer" on page 36.