Contents Names of the parts Safety precautions Installation and adjustment Preparation before washing The musts in washing Usage of the detergent Washing sequence Disposal after washing Trouble-Shooting Answers to question Packing list Specification...
Names of the parts Buzzer Outer cover of the spin tub Drain selector Inner cover of the spin tub Wash selector Spin timer Wash timer Water-filling entrance Spin tub frame water-filling translation Spin tub Control panel Cabinet Bypass channel Power cord Water level adjusting lever Overflow filter Lint filter...
Safety precautions When the machine is normally Please insert the power cord into using, please put the power plug special receptacle with rated vol- at the location easily to be insert- tage.Be sure to use single-phase ed and extracted by hand. Be sure three pins receptacle.The earthing to pull the plug off when there's terminal of the receptacle must be...
Safety precautions Do not stretch hands into the working Do not decompose, repair or alter the machine by yourself. machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not put any hot or heavy items Do not wash laundries with volatile ( such as the kettle with hot water ) materials (such as thinner, petrol etc.).
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter Put the underside of the lint filter into overflow filter overflow filter then push the upside into overflow filter lint filter...
Figure 1 indicates the ex factory installation position of the drain hose. Back Figure 1 Front Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet. Take the hose out of the fixing groove.
Voltage change This washer is assembled for 220V, but can be changed from 220V to 127V. Check your electrical source and follow the diagram below to convert voltage. Green Blue White (1). Loosen the fastening screw and take off the back cover. (2).
Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose .
The musts in washing The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
Washing sequence Wash selector Spin timer Wash timer Drain selector (If to set less than 2 min, If to set less than 1 min, in Wash selector can be Do not set drain selctor order to ensure long service life, you should first surpass 6 min soft current standard on Drain position during...
1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Proper The laundries Proper No gland are slanting (2) Close the inner and outer cover of the spin tub.
Rinsing Rinse with water-filing OVERFILL 1.Put the laundries into the wash tub. Select suitable current according to the laundries. If you find water flo- wing out here,please twist the water tap to 2.Adjust the water level limit the water filling. Set the water level with water level adjusting lever according to the laundries quantity.
Spinning 1. Put the laundries into the spin tub evenly and smoothly. 2. Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3. Spin Select suitable spin time according to the laundries, and do spinning. During spinning, if there's abnormal sound, it is generally owing to slanting placement of the laundries.
Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing.
2. Take off the corrugation pipe. Dismantle the upper part of the Water level adjusting lever corrugation pipe inside overflow filter ( as indicated in Corrugation Figure 1 Pipe 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water.
Trouble-shooting Answers to question When the remained water is frozen Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "DRAIN SELECTOR" at "OFF". If it is set at "DRAIN", it will be rather Below 50 difficult for the frozen water to melt.
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
Packing list Quantity Name One piece User's manual Water inlet hose One piece One piece Gland Twin-tub washing machine One set Specification Water level Water quantity about (L) Maximum/100 Medium/86 Minimum/72 Injection pressure (MPa) 0.02~0.2 (MPa) 0.02 0.2 Rated voltage frequency 220V/127V 60Hz 60Hz 220V/127V...