Haier HW60-B12866NZP Operating Instructions

Automatic Drum Washer
Operating Instructions
Contents
Models:
1. Notice before Use
HW60-B12866NZP
2. Safety Precautions
3. Precautions for Use
4. Preparations before Washing
5. Operational Procedure
6. Control Panel and Program Description
7. Display Screen Description
8. Other Functions
9. Fault Clearance
10. Cleaning/Maintenance
Please read this manual carefully before use.
Technology of Technology of
Please keep this manual in a safe place for future variable frequency drive power-down memory
reference.
Specifications
Power supply
220-240V/50H z
Water inlet pressure
Rated washing capacity 6.0kg
Rated spinning capacity 6.0kg
Spinning speed
1200r/m
Washing noise
50dB (A weighted)
Spinning noise
68dB (A weighted)
940mm
510mm
This product is classified as
445mm
Class I appliance. Please pay
attention to electrical safety
during use.
The diagrams in this manual are
for illustrative purpose only. In
consideration of continuous
product improvement, please
see the actual product for the
appearance, color and
accessories which may be
inconsistent with those
described in this manual. We
hereby apologize for this.
1. Notice before Use
Please install and adjust the washer according to the instructions in this
manual so that you can use it in a correct and safer manner.
To connect the water inlet pipe
1. Select a proper water tap
Water inlet pipe joint
The length of front end must be more than 10mm. If the
end face of water tap outlet is unsmooth, please file it
smooth to avoid water leakage.
2. Remove the water inlet pipe joint
When selecting the pre-wash function or the pre-wash
Press the lower end of locking lever;
program, add detergent into the pre-wash box to pre-wash
Hold the water inlet pipe, press Locking lever
the clothes;
down the slider and remove the water Slider
As for the dosage of detergent, please refer to the
inlet pipe joint;
Water inlet pipe instructions for detergent. Excessive detergent may result
in too many bubbles and spill as well as affect its
Wall 3. Install the water inlet pipe joint
If the water tap is dissolution. Special low foaming detergent for drum
Loosen the nut to the extent that
placed against the wall,
washers shall be used. When washing synthetic or wool
approximate 3-4 turns of screw thread are
you may turn this screw
fabrics, be sure to use special detergent;
to a proper position in exposed;
advance. The level of softener or liquid detergent should not be
Loosen four screws of the water inlet pipe
higher than the "MAX" mark of a distributor box.
joint to the extent that the joint can be ringed
Concentrated softener or liquid detergent should be diluted
onto the water tap;
before being added into a distributor box.
If the water inlet pipe joint cannot be ringed
Technology of
onto the water tap, please remove the bushing
automatic selection
and install again;
Bushing
Turn one of screws to an approximately
3-4 turns
proper position in advance, ring the water inlet
pipe joint onto the water tap, then evenly
Tally
Nut tighten the remaining three screws in place,
and finally tighten the nut.
4. Connect the water inlet pipe
Press down the slider and insert the
water pipe into the water inlet pipe joint;
Hook the water inlet pipe joint with
the locking lever, then loosen the slider
until a "poop" is heard.
Locking lever
5. Connect to the washer
Ring the nut at the other end of water
inlet pipe onto the water inlet valve joint;
Tighten and confirm the nut of water
inlet pipe in place.
6. Check the water inlet pipe for good connection
Check for firm connection;
After installation, turn on the water tap and
check for water leakage;
Before every use of the washer, please check
for firm connection between the water inlet pipe
and the water tap;
Never forcibly bend the water inlet pipe.
Drain pipe
Installation of the rat guard
The outlet end of drain pipe must be
1. Remove the adhesive from the back side of the felt and paste
the felt onto the back side of the protection board in a higher than 80cm and the highest point
must be less than 100cm. To prevent the
symmetrical position to the board's corners;
2. Incline the washer backwards and remove fourfeet(Fig.1); drain pipe from coming off, you may
3. Place the side with dimpled grain of rat guard inwards, then secure it to its clamp at the back of washer
pass foot bolts through four holesand tighten them to fix the rat
or to the firm holder as shown in the
guard to the shell(Fig. 2) and finally level the washer.
figure.
It is not recommended to extend the drain
pipe. If the extension pipe exceeds 2.5m
in length, simultaneous water feeding and
drainage is likely to occur. Please contact
our After-sales Service Department for the
fig. 1 fig. 2
extension of drain pipe.
Table top
Main control
panel
Drain pipe holder
Distributor boxes
Front panel
(Add a proper amount of
detergent required by washing)
Pre-wash detergent box
Main wash detergent box
Inner drum
Softener and bleach box
Window pad
Filter door
Sight glass
Lower trim
Door
Foot
Packaging bolts and accessories
Packaging bolts and accessories are used to
Table top
fix internal components of the washer during
transport and should be removed before using
the washer.
Water inlet valve
Power cord
Screw (4 pcs)
Power plug
Back cover plate Unscrew packaging bolts and take
out the back-up block.
Drain pipe clamp
Drain pipe
Splash-proof plastic
plug (4 pcs)
Shell
Block the bolt hole with a
splash-proof plastic plug.
Please keep such disassembled components
as packaging bolt and back-up block in a safe
place for future handling of the washer.
Adjustment of the feet
Accessories
Be sure to adjust four feet
Water inlet pipe assy Drain pipe holder
to level the washer before
use.
Note:
Operating
After finishing the adjustment of Rat guard
instructions
Operating Instructions Automatic Drum Washer
four feet, turn the foot support
nuts to cling to the shell in order
Felt
to support the washer.
2. Safety Precautions 3. Precautions for Use
1. Due to fluctuation of water pressure, please check all the joints of water inlet pipe, water tap and
1. The plug should be accessible after the washer is drain pipe for firm connection before washing every time. In case of loose water pipe connection or
water leakage, please turn off the water tap and take proper measures or contact our After-sales
installed in place. Do not disconnect the plug from the
Service Department for reconnection. Only after such faults are cleared can you use it again.
socket by pulling the power cord. If the power cord needs to
Electrical safety
be replaced, ask a qualified person or contact our 2. Using the washer at 0 ℃ and below may damage the water inlet valve and drainage system. If the
prompt:
washer is stored at 0 ℃ and below, be sure to move and leave it in the environment at room
After-sales Service Department for replacement. Prevent
Please pay attention to
the power cord from being pressed by any foot and from temperature for 2-4 hours before use.
electrical safety when
3. It is recommended that the washer be installed in a location with floor drainer.
such problems as break-off, flattening, etc.
using the washer.
4. Do not place any heavy object, heat-producing appliance and item liable to water/liquid leakage to
2. Power supply must use a separate socket, the grounding
avoid the deformation of table top and plastic parts.
terminal of which must be reliably grounded.
5. Do not wash such waterproof articles as raincoat, bicycle cover and down products as well as
carpet to avoid abnormal vibration or the damage to articles.
6. If a brassiere with steel wire is washed in the washer, the steel wire may bounce out. Therefore, do
3. Such overload protective devices as proper fuse must be available at the user's home.
not wash any brassiere with steel wire in order to protect the washer.
And, the ammeter, wires and socket must be able to withstand the current of 10A.
Warning sign: The
7. Do not put the clothes tainted with chemicals into the washer.
contents with this
8. Do not open any detergent distributor box during the program operation to avoid some detergent
sign involve the
1. Keep the washer away from any heat source and direct sunlight to prevent aging of plastic/rubber leaving in the box.
safety of both the
parts. 9. The washer's door is equipped with self-lock safety device. Only when the washer is in safe state
product and user. Be
(the water level is below the lower edge of sight glass, the temperature inside the drum is below 50 ℃ ,
sure to strictly follow
the inner drum is not rotating) can you unlock the door. Never forcibly open the door before the washer
1. Do not use such chemicals as flammable detergent and dry-cleaning
these instructions,
solvent to wash the clothes. Do not use any organic solvent or corrosive reaches the safe state to avoid damage to the door or scald. "Click" will be heard when opening the
otherwise the washer
liquid to wipe the exterior and rubber parts of the washer. Do not use any door. It is normal and arises from the working principle of electromagnetic lock's internal structure.
may be damaged or
flammable spray near the washer. In case of flammable gas leakage, do 10. Cut off the water supply and power supply after finishing washing every time. Moreover, clean the
the user may be
not plug in or unplug the washer. Do not use the washer near the sight glass window pad interlining to prevent contaminants from tainting the clothes again or the
injured.
surface of window pad from going moldy.
environment with flammable and explosive gas or liquid such as biomass
pool, etc. 11. When the washer is not in use, please keep the door slightly open to avoid unpleasant smell. Do
not cover the washer with a plastic bag to avoid moisture staying in the washer.
2. The washer's door is relatively hot during heating. For the purpose of safety, keep
12. If the washer is feed water from a water tank and the difference
children away from the washer. In addition, when draining hot water, be careful to avoid
between the lowest height of water level in the water tank and the highest height of washer (table top)
scald.
is 0.1~0.5m, put a proper amount of detergent along with the clothes into the washer's inner drum or
Prohibitory sign: The dilute the detergent and add it in the washer through corresponding detergent before washing to
3. After unpacking the washer, do not allow children to play with the disassembled
contents with this
prevent it from staying in the washer and affecting the washing and rinsing effect. It is not
packaging materials such as carton, plastic packaging bag and foam, etc.
sign indicate the recommended to select the prewash function and add softener in the washer in the above-mentioned
behaviors to be
situations.
4. Do not install the washer outdoors and in excessively humid environment, otherwise
absolutely prohibited. 13. Washing capacity
the moisture on electrical components may easily cause damage to the ignition system
Failure to follow these
or other accidents. In case of inadvertent water spray onto or into the washer, only after
instructions may
the washer thoroughly dries can you use it.
result in damage to
the washer or
5. Neither place the washer directly on airproof carpet to prevent its bottom vent from
personal injury.
being blocked nor close up to a wall or furniture to avoid accidents. Do not use the
washer on any platform higher than the floor, otherwise it may fall off onto the floor and
be damaged.
5. Operational Procedure
Insert the power
plug into a power
socket.
Connect the water
inlet pipe and turn
on the water tap
Put down the
drain pipe.
After finishing washing, the washer will automatically switch off.
4. Preparations
before Washing
Check the clothes for special washing
requirements and make sure that the clothes are
suitable for washing with a washing machine and
water in order to avoid the deformation and
damage of the clothes.
For the clothes tainted with much mud
and dust, please remove them before
washing.
Wash those clothes liable to color fading
separately from other clothes.
Check pockets and remove coins,
sand, hairpin and other things
from them.
Tie the ties, buckle the buttons, zip the zippers
and sew the openings.
To avoid the sound from buttons,
please turn those clothes with
buttons inside out before putting
them into the washer.
Please unfold and fluff out the clothes before
putting them into the washer. Furthermore, do
not overload the washer.
When washing small articles (e.g. handkerchief,
gloves and socks, etc.) and those clothes liable
to intertwist and wear, please put them into net
bags for washing, rinsing and spinning to prevent
them from falling between the inner drum and
window pad and further avoid incomplete
washing or damage to top-grade clothes. The
weight of articles in each net bag should not
exceed 300g and the net bags should not be
washed together with those clothes not in a net
Fadeless Terylen fabric/blend
Wool fabric bag, otherwise the washer will not be balanced,
cotton fabric fabric/chemical fiber fabric
resulting in abnormal vibration.
6 kg 3kg 1kg
Open the door, put the clothes into the washer and
Turn on the
close the door. Then add a proper amount of detergent
power
into corresponding distributor box and close it (refer to
switch.
the section of "Distributor Boxes" under "Notice before
Use" for details).
Select the washing temperature, spinning speed,
Select the desired
"Delay" function, times of extra rinse and
program.
"Intense" function, etc. as required.
Sport Wash Hand Wash
S-D Inverter
Quick Heavy
Night Wash Speed
Wool Underwear
Speed Up Temp. Synthetic Rinse
time time Power
Power
Cotton Spin
6.0kg
Start
Delay Extra Rinse Strong Anti-crease Pause Prewash Drain
HW60-B12866NZP
Press and hold 2 seconds
to set door unlocked
The "Delay" program is off by default.
To activate this program, press the
Start the selected
"Delay" button to make settings.
program.