Download Print this page
Hitachi Ultrastar 146Z10 Quick Installation Manual
Hitachi Ultrastar 146Z10 Quick Installation Manual

Hitachi Ultrastar 146Z10 Quick Installation Manual

Advertisement

Quick Links

Quick installation guide

Hitachi Ultrastar 146Z10
Ultra 160 and 320 SCSI
Models:
IC35L018UWDY10 IC35L073UWDY10
IC35L018UCDY10 IC35L073UCDY10
IC35L036UWDY10 IC35L146UWDY10
IC35L036UCDY10 IC35L146UCDY10
Handling precautions
Ÿ
Do not open the electrostatic discharge (ESD) bag
containing the drive until required.
Ÿ
Do not apply pressure on the drive during handling
or installation.
Ÿ
To prevent damage from impact or vibration always
set the drive down gently.
Ÿ
Handle the drive carefully by the edges. Do not
touch the exposed printed circuit board or any
electronic components.
Ÿ
Do not cover the breather hole! Covering the
breather hole may result in loss of data.
Ÿ
Save the packaging materials including the ESD
bag in the event that the drive must be returned.
Installing the drive
1. Backup all data.
2. Record the serial number and part number of your
hard drive for future reference.
3. Turn off the computer and remove the computer
system cover.
4. Before handling the hard disk drive, discharge any
static electricity from yourself and your clothing.
With one hand touch an unpainted metal surface
on the computer chassis, then touch the ESD bag
with the other hand for a minimum of two seconds.
5. Remove the hard drive from the ESD bag.
6. Unplug the computer.
7. Assign a SCSI address (0 through 15) to the drive
by installing a jumper on the appropriate ID bits
(pin pairs D, E, F, and G) on jumper block J4 as
shown on the shaded area in the illustration below.
Address 6 is the shipping default for 68-pin models
Address 7 is normally reserved for the host adapter
Page 1
Address jumper and drive option blocks
8. Select the desired options by placing a jumper on
the pin pair for that option. The options are listed
below cross-referenced by a letter to the two jump-
er blocks in the above illustration. Refer to the
Ultrastar 146Z10 product summary for a descrip-
tion of the options.
A
Pin pair for LED connection
B
Termination Power (68-pin model only)
C
Force Single-ended Mode
H
Enable Auto Spin (68-pin model)
Disable Auto Spin (80-pin model
I
Auto Start Delay
J
Delay Start 6/12
K
Disable Parity
L
Target Initiated Sync Negotiation
M
Disable Unit Attention
N
Reserved
version 1.0

Advertisement

loading

Summary of Contents for Hitachi Ultrastar 146Z10

  • Page 1: Quick Installation Guide

    Quick installation guide Hitachi Ultrastar 146Z10 Ultra 160 and 320 SCSI Models: IC35L018UWDY10 IC35L073UWDY10 IC35L018UCDY10 IC35L073UCDY10 IC35L036UWDY10 IC35L146UWDY10 IC35L036UCDY10 IC35L146UCDY10 Handling precautions Address jumper and drive option blocks Ÿ Do not open the electrostatic discharge (ESD) bag containing the drive until required.
  • Page 2 If the system still fails to boot up, turn off your imply that Hitachi Global Storage Technologies intends computer and remove the new drive to return to make these available in all countries in which Hitachi the system to its original configuration. Contact Global Storage Technologies operates.

This manual is also suitable for:

Ic35l018uwdy10Ic35l073uwdy10Ic35l018ucdy10Ic35l073ucdy10Ic35l036uwdy10Ic35l146uwdy10 ... Show all