Installing The Remote's Batteries; Remote Control; First Time Setup - Panasonic Viera TC-L42U5 Operating Instructions Manual

Installing the remote's batteries

Open
Push!
Incorrect installation may cause battery leakage and
z
corrosion, resulting in damage to the remote control.
Do not mix old and new batteries.
z
Do not mix different battery types (such as alkaline and
z
manganese batteries).
Do not use rechargeable (Ni-Cd) batteries.
z
Do not burn or break batteries.
z

Remote control

1無 POWER - Turns the TV on
and off.
2無 LAST - Switches to previously
viewed channel or input.
3無 STILL - Still picture direct
function key.
4無 CC - Switches the Closed
Caption mode On or Off.
5無 INPUT - Select mode "ANT/
Cable in", "HDMI 1", "HDMI 2",
"Component", "Video", "PC"
by pressing INPUT button of
Remote Control.
6無 Volume Up / Down (VOL+
/ - ) - Press to decrease or
increase the audio volume.
7無 MUTE - Turns off/on the
sound.
8無 FORMAT - To cycle through
the aspect modes.
9無 MENU - Press to display on-
screen menu.
10無 PLAY / PAUSE / STOP -
Operation of media player.
11無 SAP - Selects Secondary
Audio Programming .
12無 Channel Numbers - Directly
tune channels.
13無 SLEEP - Accesses the sleep timer.
14無 FAVORITE - Accesses the Favorites channel.
15無 USB - Viewing from USB.
16無 Channel Up / Down (CH
next channel.
17無 EXIT - Exit from the menu screen.
18無 INFO - Displays TV status information as well as program
details.
19無 RETURN - Press to Return to previous menu.
20無 COLOR KEY - Red/Green/Blue/Yellow key for various
function.
1
2
3
4
5
6
7
8
9
10
) - Press to switch to the last or
/
V
V
First time setup screen is displayed only when the TV is
turned on for the first time after the power cord is inserted
Close
into a wall outlet and when "Auto power on" is set to "No".
 Turn the TV On with the POWER button
 Configure your viewing mode
1無 Select your language and viewing mode (Be sure to select
"Home use")
2無 Please confirm your selection (Home Use) before pressing
OK button.
If you use any other step other than " Select your viewing
z
mode " then turn the TV off, or if you used the EXIT button to
quit before completing the settings, the next time you turn the
TV on, "First time setup" will not be automatically displayed.
• The settings up to that point are saved.
• You can start "First time setup" from Setup menu of
main menu at any time.
Language, ANT/Cable setup, Input labels, and Clock can also
z
be changed in the Settings Menu.
 Auto channel setup (ANT/Cable setup)
1無 Select the connected Antenna in terminal.
Not used: Go to step 4 (Label inputs)
11
Select "Not used" when no wire is connected to the
"Antenna/Cable" terminal.
Typical when a Cable/Satellite box is connected to a TV
z
12
AV input.
Prevents accidental tuning to an unavailable signal, when
z
Cable or Satellite box is used.
13
2無 Select "Start".
Skip: Go to step 4 (Label inputs)
14
Start scanning the channels (Available channels are
15
automatically set.)
16
Note:
This process may take up to 20 minutes.
z
17
This step is not needed when a Cable or Satellite box is
z
connected to an AV input.
18
3無 Finished scanning.
the Auto program scan is successfully completed.
If there is no available channel, return to ANT/ Cable setup. "Not
used" will be selected.
19
Operation of the EXIT button during "First time setup"
z
20
Press the button once to display confirmation screen.
Press again to close confirmation screen.
[EXIT confirmation screen]
Yes
No
4無 Give names to the TV's inputs (Label inputs)
When done, select NEXT and press OK to go to the next step.
Label: [BLANK] Not used/Blu-ray/DVD/DVD REC/HOME THTR/
GAME/COMPUTER/VCR/CABLE/SATELLITE/DVR/
CAMERA/MONITOR/AUX/RECEIVER/MEDIA CTR/
MEDIA EXT/OTHER
• Select "Not used" for any back-panel input that has
no device connected to it. Afterward, the input will be
skipped when pressing INPUT, for your convenience.
• The input labels can be changed at any time from the
TV's setup menu.
5無 Adjust the Clock (Set clock)
When done, select NEXT and press OK to go to the next step.
6無 Complete the First time setup.
Congratulations! You are done.
The First time setup can be repeated at any time.
Press MENU and select SETUP; then "First time setup".
To watch TV via a Cable box, Satellite receiver, or any
other source (DVD, DVR, gaming device, etc.), press the
INPUT button and select the appropriate input.

First Time Setup

Completion message is displayed when
Exit "First time setup"
Return to the original screen.
4