Electrolux EI23CS65KS Service Data Sheet

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 0° F FREEZER & 37° F
FRESH FOOD (2500 ++ V5)
65°F (18°C) Ambient
Type A with Run/Start
Capacitor
Variable Speed Standard Variable Speed
Operating Time 74 to 84% 32 to 40% 100%
-2° to 2° F 0° to 4° F -1° to 3° F
Freezer Temperature
-19° to -17° C -18° to -16° C -18° to -16° C
34° to 39° F 34° to 39° F 34° to 39° F
Refrigerator Temperature
1° to 4° C 1° to 4° C 1° to 4° C
5 to 12 psig 5 to 12 psig
Low Side Pressure (cut-in)
43 to 83 kPa 43 to 83 kPa
-2 to 2 psig -2 to 2 psig -2 to 2 psig
Low Side Pressure (cut-out)
-14 to 14 kPa -14 to 14 kPa -14 to 14 kPa
High Side Pressure 90 to 105 psig 90 to 115 psig 120 to 135 psig
(last 1/3 cycle) 621 to 724 kPa 621 to 793 kPa 827 to 931 kPa
Wattage (last 1/3 cycle) 50 to 60 90 to 130 60 to 70
Amps (running) 0.5 to 0.9 0.7 to 1.1 0.6 to 1.0
Base Voltage 115 vac (127 vac max)
DEFROST SPECIFICATIONS
Thermostat
Cabinet Size
Cut-in Cut-out Watts
23' CD, 26' 25° F (-4° C) 47° F (8° C)
Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time.
CONDENSER FAN MOTOR
Watts RPM
3.1 1100 CW Opposite Shaft
90°F (32°C) Ambient
Standard
55 to 65%
-1° to 3° F
-18° to -16° C
IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION
34° to 39° F
1° to 4° C
Error Codes
5 to 12 psig
N/A
43 to 83 kPa
Display
-2 to 2 psig
FZ FF
-14 to 14 kPa
-- OP-
130 to 155 psig
896 to 1069 kPa
-- OP¯
100 to 140
0.8 to 1.2
OP --
-- SH-
Heater
-- SH¯
Ohms
450 30 SH --
SY CF
Amps
SY CE
0.03 Running
SY EF
SERVICE DATA SHEET
240389648
ICE & WATER - AUTOMATIC DEFROST
SIDE BY SIDE - R134a
Special Modes
Display Activate/Deactivate
Interpretation Mode (press for up to 10 sec.
FZ FF
simultaneously)
Open FF mid-level Manual d F FF UP and FF DOWN/
thermistor Defrost same to deactivate
Open FF upper-level Display/ 77 77 FZ UP and FF DOWN/
thermistor Showroom Power-on-Reset (POR)
Open FZ thermistor Sabbath Sb Sb FZ DOWN and FF UP/
same to deactivate
Shorted FF mid-level Diagnostic No FF or FZ display, FZ UP and FZ DOWN/FF
thermistor all UI LEDs on. UP to deactivate
Shorted FF upper-level Notes:
thermistor
• Always check for pin back-outs, pinched or damaged wires
before replacing components.
Shorted FZ thermistor
• Determine whether failure is caused by the component, main
control board or wiring. Contact TID before replacing main
UI to Main Control Board
control board.
communication failure;
• Refer to Service Manual for additional information.
on start up
UI Main Control Board
communication error;
after a period in operation
Evaporator fan failure
Diagnostic Mode
Activate: Press FZ UP and FZ DOWN temperature pads for up to 10 sec. simultaneously.
Press FF UP to advance through tests.
Deactivate: Press FF UP for up to 10 sec. Diagnostic Mode will automatically deactivate after 5 min. of
inactivity. Note: Silence alarm.
• Tests marked with "*" may not be applicable to this unit and will not be displayed in Diagnostic Mode.
• Tests displayed in diagnostic mode but not described below are for internal purposes only; advance through.
• View UI display for "on," "off," "CL," "OP," "SH," "LO," "HI" or numerical results of tests.
• Listen for operating sounds; feel for heat or air flow as appropriate to determine results of tests.
Test To activate test: Passing result
-- First Screen -- All LED lights on UI illuminated
-- Second Screen -- All segments on UI temperature displays illuminated
-- Third Screen -- Blank UI display, no lights illuminated, no shadowing; "-" and "+"
blinking on FF display side to show location.
28 Dispenser Paddle Press disp. paddle "on" on UI when depressed; "off" when released
1* Standard Press power on-off Compressor running when "on"; stopped when "off"
Compressor
2 Defrost Heater Press power on-off Defrost limit switch must be closed; verify "CL" in test 26.
Feel for heat from defrost heater when "on".
If "OP" in test 26, heater will not activate.
3 FF Light Press power on-off With FF door open, FF lights on when "on"; off when "off"
8 Water Valve Press power on-off FF door must be closed.
(Dispenser) Be prepared to collect water at dispenser.
Water dispenses when "on"; stops when "off"
9 FZ Light Press power on-off With FZ door open, FZ lights on when "on", off when "off"
10 Auger Motor Press power on-off FF door must be closed.
Motor running when "on"; motor stopped when "off"
FF door must be closed. Do not leave solenoid in activated state.
11 Cube/Crush Press power on-off
Solenoid Solenoid activated when "on"; deactivated when "off"
41* Perfect Temp Drawer Press power on-off PTD UI illuminated when "on", off when "off"
(PTD)
12* VCC Condenser Fan Press power on-off Fan running when "on"; stopped when "off"
38* VCC Compressor Press power on-off Compressor running when "on"; stopped when "off"
15 Evaporator Fan Press power on-off Fan running for minimum of 10 sec. when "LO" or "HI"; stopped when
"off". Feedback failure if fan starts but runs less than 10 sec. Listen for
speed change from "LO" to "HI".
22 Damper Press power on-off With inspection mirror, observe damper open when "OP"; closed when "CL"
23 FF Door Open/close FF door "CL" on UI when door closed; "OP" when open
24 FZ Door Open/close FZ door "CL" on UI when door closed; "OP" when open
26 Defrost Limit Switch Activates automatically "CL" on UI when closed; "OP" when open
36 Ice Chute Door Depress ice chute door "OP" on UI when manually opened; "CL" when closed. Or, using "power
or press power on-off on-off", "OP" on UI when solenoid activated, "CL" when deactivated
29 FF Thermistor Activates automatically UI shows temperature sensed by FF thermistor; pass if within 10°F of
Mid-level temperature measured with gauge at mid-level FF thermistor location.
"OP-" if open; "SH-" if short
30 FZ Thermistor Activates automatically UI shows temperature sensed by FZ thermistor; pass if within 10°F of temperature
measured with gage at FZ thermistor location.
"OP" if open; "SH" if short
33 Ambient Thermistor Activates automatically UI shows temperature sensed at main board; pass if within +20°F/-10°F
@ Main Board of temperature measured with gauge at main board location.
"OP" if open; "SH" if short
35 FF Thermistor Activates automatically UI shows temperature sensed by upper level FF thermistor; pass if within
Upper-Level 10°F of temperature measured with gauge at upper-level FF thermistor
location. "OP¯" if open; "SH¯" if short
34 Ambient Thermistor Activates automatically UI shows temperature sensed at UI; pass if within +20°F/-10°F of tem-
@ UI perature measured with gauge at UI location. "OP" if open; "SH" if short
0- Firmware Press power on-off Displays digit sequence; record
Parameters
2- Main Board Press power on-off Displays digit sequence; record
Firmware
4- UI Firmware Press power on-off Displays digit sequence; record
IMPORTANT SAFETY NOTE
The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make
repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.
IMPORTANT
If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured.
CAUTION
All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at
200°F and flash ignite (burn) at 500°F. Excessive heat will distort the plastic liner.