AUDIO TELEX ATC5488 Installation Instructions

Tone generator module

Advertisement

ATC5488 TONE GENERATOR MODULE
INSTALLATION
I
NSTRUCTIONS
Thank you
for
choosing an
Audio Telex ATC5488 tone
generator
module.
The ATC5488
has
four
tones
available.
These
are
Evacuatim
and
Al€rt
Tones,
both
to
A52220.1-2
standards,
as
well
as
a
Bell
Tone
and
a
Pre
Announce
Chime. lnstallation into
any
Audio Telex manufuchred mixer or amplifier is
made
simple
by utilising a
standard
'€nd' qpe
connector
plug
supplied
on
the
module
and
a
rec€ptacle, already
installed into
the
mixer
or
amplifier.
Please
follow
these
easy
instructions
for
installation.
E
The
installation of lhe ATC548E involvcs
eccess
to thc inside of the rmplitrers
or mixerg Inst tlrtion
should
only
bc
rttemptcd
by a
qualifed technicirn. Alwlys turn off
the
AC power and rcmove the AC power cord bcfore attempting
to
scc.ss
thc
inside
of
lhcsc
prodlcts.
Plerse
contrct your
Errest
Audio Telex oftce
for detdls of your trefcat
qualified
technicirn
'
For installation into an
lC30
amplifier:
Locate
the
empty
7
pin 'and'
connector receptacle on the
mixer
PCB to the
left
of the
heat
sink when
looking
from the front
panel.
Connect
the module to this
receptacle,
ensuring that the
wires from
the connector exit
towards the rear
ofthe amplifier.
For installation into an
AT SERIES
amplmer:
Lo€ate the empty
7
pin 'end'
connector receptacle
on
the
mixer
PCB
between
the
reble pot
and
the master
volume
pot.
Connect the module
lo
this
receptacle,
orsuring that
the
wires
from the
connector
exit
towards the
right
hand side
ofthe amplifier
when
looking
from
tlre
front
panel.
For installation into an
SA
SERIES amplifier:
Locate the
ernpty
7 pin 'end'
connector receptacle
on the mixer
PCB
betweer input
Ch.
6
pot and
the
bass
tonal
contol
pot.
Connect the
module
to this
receptacle, ensuring
that
the
wires from
the
conneclor
exit
towards the rear
ofthe amplifier.
For
lnstallatlon into
a
TX6000
or
TX8000 mlxer:
Locate the empty 7
pin 'end'
connector
receptacle
behind input Ch.
5
pot
on the
mixer
PCB.
Comect
the module
to this receptaclg
ensruing that the
wires from
the connector
exit
towards the rear
of
the
mixcr-
For installaUon lnto
a
TX8200
stereo
mlxer:
Locate
the
eflpty
7
pin
'end'
corulector
receptacle
on
the
mixer
PCB
b€tween
input Ch.
8 pot
and
the
Left
Channel
Mast€r
out
pot.
Connect
the
module
to this
receptacle, ensuring
that
the
wtes
from
the
connector
exit
towards the rear
ofthe
mixer.
Connectlon to ampllfler:
Connections
Orange=
Output
Black
:
Grormd
Blue
=
Mute switch
to I
Red
=
DC Supply
(Min. I2VDC, Max.
t
SVDC)
Black
=
Common
White
=
Evac,uation
Tone
Yellow:
Bell
Tone
Purple
=
Alert
Tone
Blue
=
Pre
Annormce
Chime
Connectlons to swltched signal:
Notes
Trim
Pot
Note that the
tim
pot
located
in
positim RlO
on
the
module
attenuates
the level
out of
the
ATC5488
and
works
in
an
urti-clockwise
fashion ie,
hnned
fully clockwise
will
completely
att€nuate
the
signal outpl$
whilst hrned fully anti-clockwise
will
allow
full
signal present
though to
the
amplifier
stage.
r\'.1
ri

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ATC5488 and is the answer not in the manual?

Questions and answers

Summary of Contents for AUDIO TELEX ATC5488

  • Page 1 Evacuatim Al€rt well Chime. lnstallation into Tones, both A52220.1-2 Bell Tone Announce standards, '€nd' qpe plug Audio Telex manufuchred mixer or amplifier is by utilising a simple made standard connector supplied module installed into mixer amplifier. follow rec€ptacle, already instructions installation.
  • Page 2 TONE IIODULE CEHMEN ILACK = LEVA- rlUT ORANGE OU]PUT I,IHIIE EVAC BLACK @IruND YB.LII, = BELL ELUE I{UTE SITITCH PURPLE ALERT SUPPLY DLIJE ANNT]UNCE 1aVDC UAX 18VDC) ATC54B8 TINE MEDULE...

Table of Contents