Advertisement
Quick Links
f
I
~ I
;
~
~
i
j
~
£j:i'-; , ,,"
SO-O216A-xxx
SERIES
118127X
DODGEDURANGO
OVERHEAD
CONSOLE
for use with FLIPDOWN
VIDEO
SYSTEM
~
OPTIONAL ACCESSORIES MA y BE ADED:
ESCORT PASSPORT 4600 RADAR DETECTOR
MINI- TRIP COMPUTER FROM O.E.M. OVERHEAD
1
2
These instructions are intended for use only by experienced professionals in the automotive
customizing business. Special tools and equipment, as well as specialized handling and care
of product during installation, may be required. Before beginning this installation, carefully
read through the following instructions. Use extreme care when cutting headliner material.
Check for wiring or other componentry above headliner material. Cut only where indicated.
Materials/ Tools required for this installation:
I. #2 Phillips screwdriver
2. Powered screwdriver or drill with adapter
3.
1/8" drill bit
4. ~" hex socket bit
5; Razor knife or similar
6. A wl or similar tool
7. Audiovox
Series 640/641 Video Module
,
FOR USE IN VEHICLES
EQUIPPED WITH FACTORY
INSTALLED
REAR AIR CONDITIONING
ONL Y.
Apr.13,1998
Printed in the U.S.A
INSTALLATION
I;,\,STRUCTION
# 44-0021A
Advertisement
Summary of Contents for Dodge 118127X
- Page 1 Series 640/641 Video Module FOR USE IN VEHICLES REAR AIR CONDITIONING INSTALLATION I;,\,STRUCTION # 44-0021A SERIES 118127X DODGEDURANGO for use with FLIPDOWN 2. Powered screwdriver or drill with adapter 4. ~" hex socket bit 6. A wl or similar tool EQUIPPED WITH FACTORY ONL Y.
- Page 2 MA TERIALS PROVIDED lrEMi~,pe~cription ..;!~",;;c..c;, SCREW, # 6 X Y2 PPH SCREW,#8X* SCREW, # 8 X 11/4 PWH FRONT MOUNTING BRACKET COMPUTER MOUNTING BRACKET REAR MOUNTING BRACKET RADAR DETECTOR HOUSING BLOCK OFF CONSOLE FRONT LIGHT FRONT LIGHT TRIM INSTALLATION INSTRUCTION # 44-0021A FOR INST ALLA TION ,gTY...
- Page 3 I. PREPARATION OF VEHICLE INTERIOR .""4.' FIGURE 3. Disconnect wiring harness from console. See fig. 2 4. Individually cut and remove the green, white, and black wires that control the map lights from the connector on the mini-trip computer. 5. Remove and discard (4) four screws which secure the mini-trip computer to console.
- Page 4 7" ~" -~~:i" ~ ~5rf:; ."," ~",,~' ,~~ FIGURE II. PREPARATION OF CONSOLE FOR INSTALLATION FIGURE 8. Carefully trim headliner and drill (2) two Y2" holes in return air grille to allow for screws to pass through when mounting bracket. See fig. 4. 10.
- Page 5 Install fro~,tjig4t(item ,-,,"= , "'" -using (3) three::~~6;;kV2" screws {item Install front light trim (item II pg 2) around light. See figure 7. FIGURE Install Escort Passport 4600 radar detector housing (item 7 pg 2) and secure using (4) four # 6x Y2"...
- Page 6 FIGURE 10 Install O.E.M. mini-trip computer and secure using (4) four #6 x 1f2" screws (item I pg 2). See figure 11. Do not overtighten c. Install O.E.M. mini-trip the backside of opening in console. Install computer mounting bracket (item 5 pg 2) and secure using (2) two # 6 x Y2"...
-
Page 7: Inst Alla Tion Of Console
III. INST ALLA TION OF CONSOLE " " " NOTE: Additional a"ssistance in mounting advised to prevent damage to console or components. 13. Install and route all accessory wiring, video and audio cables, and any other added component requirements to their respective places in the vehicle. - Page 8 17. Using an awl or similar tool, align the front mounting holes in console with holes in bracket. Secure using (2) two # 8 x 1 ~" screws (item 3 pg 2). See figure 14. Caution: Do not overtighten screws. Figure 14 "'...