Pc Menu Settings; Rs232C Settings - Sanyo 42LM4WPN Instruction Manual

GB

PC menu settings

Connect your PC to the connector on the left side terminal of the
set. Once connected select PC mode via the v button on your
remote control. The set will become a monitor for the PC.
By pressing the MENU button on the remote control a menu window
will appear on screen, this allows the settings to be adjusted.
Main Menu
Picture
Setting
: Select
To adjust the Picture settings select picture using the e or d buttons
on the remote then the 8 button to enter the following picture
settings menu.
Press the 7 or 8 buttons to adjusted the Picture brightness and the
same to adjust the contrast of the picture.
Picture
Brightness
Contrast
Position
Video Adjust
Auto Adjust
Resolution
White Tone R
White Tone G
White Tone B
Native Resolution
: Select
Picture position changes the picture horizontally or vertically, this is
done by using the 7 or 8 buttons on the remote control.
Video adjust changes the Phase and the clock of the screen. If the
picture is blurred or grainy this function will adjust it to a clearer
picture.
Auto Adjust will automatically adjust the picture by using the 8
button. This will change all the above settings automatically .Auto
adjust can also be achieved by pressing the
button on the remote control
Resolution displays the current resolution of the picture. This is just
for information and cannot be adjusted.
Using the 7 or 8 buttons it is possible to adjust the tone of the
screen using the White tone Red(R) / Green (G)/ Blue(B). This will
adjust the picture to show more of the chosen colour for example if
red is selected you can adjust the red in the picture to increase or
decrease using the 7 or 8 buttons
Native Resolution is used when the PC can output WXGA
1366 x 768. The setting on your Monitor set can be changed
to receive XGA/WXGA signal using the 7 or 8 buttons . Once the
signal has been selected, save the settings by switching off then on
the monitor using the power button.
To select the Settings menu press the menu button on your remote
and using the e or d buttons to select Settings. The 8 button will
enter the settings menu.
Setting
CHILD LOCK
OSD Language
Timer
AV2
Power save
: Select
Child lock/ Timer and AV2 settings are the same as in the TV mode
(pg 7)
Power save if turned ON will turn the LCD monitor into Powersave
mode after 1 minute if no signal is detected, the LED light will turn
blue to indicate stand by. The TV will automatically turn on when a
signal has been detected. Use 7 or 8 buttons to select ON or OFF.
PC OPERATION
: Adjust
: Exit
MENU
1024 X 768 @60Hz
XGA / WXGA 1366 x 768
: Adjust : Back
MENU
rD
OFF / ON
English
RGB, HV/ Y,Pb,Pr
OFF/ON
: Adjust : Back
MENU

RS232C settings

The TV control commands are used to control a TV through RS-
232C from a computer.
ITEM
Synchronous system
Transmission Speed
Data Length
Parity
Stop Bit
Flow Control
Serial Interface Specification
Transfer Specification
1. Transmission Speed: initial setting value is 19200
2. Transmission speed can be changed by service mode.
Connection
The Designated RS-232C serial cable that is provided with the LCD
monitor must be used for a connection to a computer and LCD
monitor
Notes for communication
PC
COM 1
1
CD
2
RXD
3
TXD
DTR 4
5
SG
6
DSR
7
RTS
8
CTS
9
RING
(D-Sub 9 Pin)
The TV command is defined by one command/ one line that starts
with "C" and ends with carriage return (0x0D)
There are two types of commands:
Functional Execution Command e.g Co5[CR] (table on page 75)
Status Read Commands e.g "CR0 [CR] (see table on page 75)
Setting the monitor address in RS232 mode
To Access hotel mode press the green button on the remote control
and hold for 5 seconds. A new screen will appear.
Hotel
Hotel mode
On program
Preset
Address
Baud Rate
: Select
Each monitor can have a specific Address for example 007, which
helps command that monitor individually and will not effect other
monitors connected to a controlling PC
Address format command
The addressing format command is used for operating multiple
monitor sets from a single PC via the RS232C command line. If you
set your monitor address to '000', it will never respond to any
addressing command from the PC.
If the address from the PC is 'FFF', all monitor sets will execute the
command.
The Address format command is defined by one command, one line
which starts with 'A' and ends with carriage return.(0 x0D)
The Monitor starts to decode when it receives a carriage return
(0x0D)
An address is added at the top of a control command (same as a
address command)
Example:
Functional execution command:
"A001C05" [CR] means address is 001 and the control command is
C05
Status read command
"A001CR0"[CR] means address is 001 and command is CR0
The monitor can set its own address in the hotel option menu
(above) The address range is 000 - 999, the default address will be
000
The baud rate indicates the unit for transfer speed of data
from the PC to the monitor sets
SPECIFICATION
Asynchronous
9600 / 19200
8 bit
None
1
None
TV CONTROL
PORT
1
N.C.
2
RXD
3
TXD
4
N.C
5
SG
6
N.C
7
RTS
8
CTS
9
N.C.
(D-Sub 9 Pin)
ON / OFF
OFF/ 1~99 / AV1-AV3 /RGB/ HDMI/ PC
ON / OFF
007
19200
: Adjust : Exit
MENU
GB
9