Advertisement
incLuDeD GLitch buSter caPacitor
(in addition to "Optional Accessories" section on page 1 of Havoc Sport instructions)
The Havoc 1S includes a Novak Glitch Buster Capacitor (#5626) to
eliminate noise generated from the servos. It is highly recommended to
install the Glitch Buster when using a 2.4GHz radio system.
To install, simply plug the Glitch Buster directly into any open channel or
battery slot on the receiver. Remember to match the polarity of the Glitch
Buster plug and the other components plugged into the receiver. Reversing
the polarity will cause damage to the electronics and void warranty.
GearinG
(in addition to "Proper Gear Selection" section on page 5 of Havoc Sport instructions)
Neither the Havoc 1S nor the brushless motor should be hotter than 160°F
after a 5 min. run. If either temperature is higher, the gearing should be
lowered until both the ESC and the motor are under 160°F. The cooler the
ESC runs, the better the performance of the system.
refer to the gearing chart below for 1-cell li-Po battery recommendations.
application
8.5t
10.5t
1/12-scale
2.00"/51mm
2.30"/58mm
oval
2.6"/66mm
3.0"/76mm
Li-Po cut-off circuitrY
(in addition to "Li-Po Cut-Off Circuitry" section on page 5 of Havoc Sport instructions)
The Havoc 1S is equipped with built-in Smart-Stop Li-Po Cut-Off Circuitry that
prevents the battery from going below the critical voltage level of 3.125V.
motor comPatibiLitY
(in addition to "Precautions" section on page 1 of Havoc Sport instructions)
The Havoc 1S ESC will operate with any brushless motor that has built-in
thermal protection that follows ROAR guidelines, down to 8.5-turns, such as
Novak's Ballistic and SS Pro Brushless Motors.
ProDuct warrantY: (in addition to the "Product Warranty" on page 1 of Havoc Sport instructions)
Warranty does not cover damage caused by the use of Ni-MH battery packs, using more than 1-cell
Li-Po batteries, or reversing the polarity of the Glitch Buster plug and other components plugged into
the receiver.
www.teamnovak.com
incLuDeD GLitch buSter caPacitor
(in addition to "Optional Accessories" section on page 1 of Havoc Sport instructions)
The Havoc 1S includes a Novak Glitch Buster Capacitor (#5626) to
eliminate noise generated from the servos. It is highly recommended to
install the Glitch Buster when using a 2.4GHz radio system.
To install, simply plug the Glitch Buster directly into any open channel or
battery slot on the receiver. Remember to match the polarity of the Glitch
Buster plug and the other components plugged into the receiver. Reversing
the polarity will cause damage to the electronics and void warranty.
GearinG
(in addition to "Proper Gear Selection" section on page 5 of Havoc Sport instructions)
Neither the Havoc 1S nor the brushless motor should be hotter than 160°F
after a 5 min. run. If either temperature is higher, the gearing should be
lowered until both the ESC and the motor are under 160°F. The cooler the
ESC runs, the better the performance of the system.
refer to the gearing chart below for 1-cell li-Po battery recommendations.
application
8.5t
10.5t
1/12-scale
2.00"/51mm
2.30"/58mm
oval
2.6"/66mm
3.0"/76mm
Li-Po cut-off circuitrY
(in addition to "Li-Po Cut-Off Circuitry" section on page 5 of Havoc Sport instructions)
The Havoc 1S is equipped with built-in Smart-Stop Li-Po Cut-Off Circuitry that
prevents the battery from going below the critical voltage level of 3.125V.
motor comPatibiLitY
(in addition to "Precautions" section on page 1 of Havoc Sport instructions)
The Havoc 1S ESC will operate with any brushless motor that has built-in
thermal protection that follows ROAR guidelines, down to 8.5-turns, such as
Novak's Ballistic and SS Pro Brushless Motors.
ProDuct warrantY: (in addition to the "Product Warranty" on page 1 of Havoc Sport instructions)
Warranty does not cover damage caused by the use of Ni-MH battery packs, using more than 1-cell
Li-Po batteries, or reversing the polarity of the Glitch Buster plug and other components plugged into
the receiver.
www.teamnovak.com
13.5t
17.5t
21.5t
2.56"/65mm
2.75"/70mm
3.00"/76mm
3.3"/84mm
3.6"/91mm
4.0"/102mm
13.5t
17.5t
21.5t
2.56"/65mm
2.75"/70mm
3.00"/76mm
3.3"/84mm
3.6"/91mm
4.0"/102mm
incLuDeD GLitch buSter caPacitor
(in addition to "Optional Accessories" section on page 1 of Havoc Sport instructions)
The Havoc 1S includes a Novak Glitch Buster Capacitor (#5626) to
eliminate noise generated from the servos. It is highly recommended to
install the Glitch Buster when using a 2.4GHz radio system.
To install, simply plug the Glitch Buster directly into any open channel or
battery slot on the receiver. Remember to match the polarity of the Glitch
Buster plug and the other components plugged into the receiver. Reversing
the polarity will cause damage to the electronics and void warranty.
GearinG
(in addition to "Proper Gear Selection" section on page 5 of Havoc Sport instructions)
Neither the Havoc 1S nor the brushless motor should be hotter than 160°F
after a 5 min. run. If either temperature is higher, the gearing should be
lowered until both the ESC and the motor are under 160°F. The cooler the
ESC runs, the better the performance of the system.
refer to the gearing chart below for 1-cell li-Po battery recommendations.
application
8.5t
10.5t
1/12-scale
2.00"/51mm
2.30"/58mm
oval
2.6"/66mm
3.0"/76mm
Li-Po cut-off circuitrY
(in addition to "Li-Po Cut-Off Circuitry" section on page 5 of Havoc Sport instructions)
The Havoc 1S is equipped with built-in Smart-Stop Li-Po Cut-Off Circuitry that
prevents the battery from going below the critical voltage level of 3.125V.
motor comPatibiLitY
(in addition to "Precautions" section on page 1 of Havoc Sport instructions)
The Havoc 1S ESC will operate with any brushless motor that has built-in
thermal protection that follows ROAR guidelines, down to 8.5-turns, such as
Novak's Ballistic and SS Pro Brushless Motors.
ProDuct warrantY: (in addition to the "Product Warranty" on page 1 of Havoc Sport instructions)
Warranty does not cover damage caused by the use of Ni-MH battery packs, using more than 1-cell
Li-Po batteries, or reversing the polarity of the Glitch Buster plug and other components plugged into
the receiver.
www.teamnovak.com
incLuDeD GLitch buSter caPacitor
(in addition to "Optional Accessories" section on page 1 of Havoc Sport instructions)
The Havoc 1S includes a Novak Glitch Buster Capacitor (#5626) to
eliminate noise generated from the servos. It is highly recommended to
install the Glitch Buster when using a 2.4GHz radio system.
To install, simply plug the Glitch Buster directly into any open channel or
battery slot on the receiver. Remember to match the polarity of the Glitch
Buster plug and the other components plugged into the receiver. Reversing
the polarity will cause damage to the electronics and void warranty.
GearinG
(in addition to "Proper Gear Selection" section on page 5 of Havoc Sport instructions)
Neither the Havoc 1S nor the brushless motor should be hotter than 160°F
after a 5 min. run. If either temperature is higher, the gearing should be
lowered until both the ESC and the motor are under 160°F. The cooler the
ESC runs, the better the performance of the system.
refer to the gearing chart below for 1-cell li-Po battery recommendations.
application
8.5t
10.5t
1/12-scale
2.00"/51mm
2.30"/58mm
oval
2.6"/66mm
3.0"/76mm
Li-Po cut-off circuitrY
(in addition to "Li-Po Cut-Off Circuitry" section on page 5 of Havoc Sport instructions)
The Havoc 1S is equipped with built-in Smart-Stop Li-Po Cut-Off Circuitry that
prevents the battery from going below the critical voltage level of 3.125V.
motor comPatibiLitY
(in addition to "Precautions" section on page 1 of Havoc Sport instructions)
The Havoc 1S ESC will operate with any brushless motor that has built-in
thermal protection that follows ROAR guidelines, down to 8.5-turns, such as
Novak's Ballistic and SS Pro Brushless Motors.
ProDuct warrantY: (in addition to the "Product Warranty" on page 1 of Havoc Sport instructions)
Warranty does not cover damage caused by the use of Ni-MH battery packs, using more than 1-cell
Li-Po batteries, or reversing the polarity of the Glitch Buster plug and other components plugged into
the receiver.
www.teamnovak.com
13.5t
17.5t
21.5t
2.56"/65mm
2.75"/70mm
3.00"/76mm
3.3"/84mm
3.6"/91mm
4.0"/102mm
13.5t
17.5t
21.5t
2.56"/65mm
2.75"/70mm
3.00"/76mm
3.3"/84mm
3.6"/91mm
4.0"/102mm
Advertisement
