Advertisement
STEP 4
HOOK-UP INSTRUCTIONS
Refer to set-up photo below
1. INSTALL MOTOR CAPACITORS
Electric motors generate radio noise that can interfere
with your receiver and cause radio problems. Included
in the accessory kit with the speed control are three
0.1µF (50V) non-polarized, ceramic capacitors. These
capacitors muse be installed on every motor to help
reduce the noise generated by the motor and also to
prevent possible damage to the speed control.
Solder 0.1µF (50V) capacitors between:
• POSITIVE (+) motor tab & NEGATIVE (
• POSITIVE (+) motor tab & GROUND tab*.
-
• NEGATIVE (
) motor tab & GROUND tab*.
*If your motor does not have a ground tab, solder the
capacitor leads to the can of the motor as shown below.
Extra 0.1µF capacitors
Ground / motor can
available in Novak kit #5620.
2. CONNECT SPEED CONTROL TO THE RECEIVER
After the proper input plug plastic has been installed
to match the receiver (Refer to Step 1), plug the speed
control into the
THROTTLE CHANNEL
3. CONNECT SPEED CONTROL TO THE BATTERY PACK
Plug the white JST connector from the speed control
into the JST/Tamiya style connector on a fully charged
6 or 7 cell battery pack
(1.2 volts DC/cell)
wire is negative (-) and the red wire is positive (+).
4. CONNECT SPEED CONTROL TO THE MOTOR
Plug the bullet connector on the red wire (+) of the
speed control to motor positive. Plug the other bullet
connector, on the blue wire (-), to motor negative.
USE ONLY STOCK AND MILD MODIFIED MOTORS with
the Explorer speed control––Using hotter motors and
lower gear ratios will cause speed control to overheat.
A wiring kit with bullet connectors and a JST/Tamiya
connector is available in Novak kit #5810.
TIP: Twisting the BLUE & RED motor wires one or two times around
each other as they go to motor can help reduce any radio noise
that may be emitted from the power wires. Refer to Set-Up photo.
5. OPTIONAL USE OF SCHOTTKY DIODE
The Explorer does not require an external Schottky
diode. However, using one will increase the efficiency
and reduce the operating temperature of the ESC.
Solder the lead
to the silver stripe on the body
CLOSEST
of the Schottky diode to the
POSITIVE
Solder the lead
OPPOSITE
the silver stripe on the body
of the Schottky to the
NEGATIVE
(-) motor tab.
Schottky diodes are available in Novak kit #5640.
If installed backwards, a Schottky diode will be destroyed. The body
of a bad diode will normally crack open. Replace only with Schottky
diodes that have a minimum rating of 35 volts / 8 amps.
EXPLORER SET-UP
(-)
(+)
Trail excess wire
red wire
off antenna mast.
(motor posative)
(Do not cut or coil)
Tip: Twist motor wires
to reduce radio noise!
red wire
(battery positive)
black wire
(battery negative)
(-)
(+)
Keep receiver
and antenna
away from
motor, servo,
battery, and
power wires.
STEP 5
TRANSMITTER ADJUSTMENT
Proper transmitter adjustment is important for optimum
performance from your speed control. The basic throttle
channel adjustments for the transmitter are as follows:
For proper ESC operation adjust transmitter as follows:
1. Set HIGH ATV or EPA to maximum setting.
[Controls amount of throw from neutral to full throttle]
2. Set LOW ATV , EPA , or ATL to maximum .
[Controls amount of throw from neutral to full brakes]
[Reduce this after ESC adjustment to reduce amount of brakes]
3. Set EXPONENTIAL to zero .
-
) motor tab.
[Controls the linearity of the throttle channel]
4. Set THROTTLE CHANNEL TRIM to middle setting.
[Adjusts the neutral position of speed control]
[Increase or decrease after ESC adjustment to adjust coast
brakes––can be used to give braking in neutral trigger position]
5. Set THROTTLE CHANNEL REVERSING SWITCH
normal position.
Negative (-) motor tab
6. Set MECHANICAL THROW ADJUSTMENT
with 2/3 throttle and 1/3 brake throw.
0.1µF Capacitors
[Adjusts pistol-grip transmitter's throttle trigger throw]
Schottky diode
STEP 6
Positive (+) motor tab
SPEED CONTROL ADJUSTMENT
Before beginning this step, the speed control should be
connected to the receiver and to a charged 6 or 7 cell
battery pack, and the transmitter should be adjusted.
Adjustment of your Explorer speed control is required for
of the receiver.
proper operation. When the status LED is red, the speed
control is in the neutral position (no throttle or brake).
When the status LED is green, the speed control is either at
the full throttle or full brake position.
. The black
When adjusting the speed control, DO NOT rotate the
pots beyond their end stops––this will damage the pots.
1. DISCONNECT THE MOTOR
The motor is not needed for adjustments.
2. CONNECT THE BATTERY
Plug the Explorer Sport into a fully charged 6 or 7 cell
battery pack.
3. TURN ON THE TRANSMITTER POWER
4. TURN ON THE SPEED CONTROL
Slide the
5. ADJUST THE NEUTRAL POT OF SPEED CONTROL
Rotate the
status
6. ADJUST THE HIGH SPEED POT OF SPEED CONTROL
Hold the transmitter throttle at full throttle and rotate
the
HIGH SPEED
turns solid green.
LED
NOTE: If the
(+) motor tab.
reach full speed before the transmitter is at full throttle.
7. SET THE BRAKES TO MAXIMUM AT TRANSMITTER
Hold the transmitter throttle at full brakes and rotate
the
LOW ATV
ter until the status LED begins to turn green . After speed
control adjustment has been completed this setting can be
reduced if you feel there is too much braking.
NOTE: If the
adjusted too high you will reach full brakes before the
transmitter is at full brakes.
8. CHECK OPERATION OF THE SPEED CONTROL
Connect the motor and check for proper operation.
With no throttle or brake applied the status LED should
blue wire
be solid red and the motor should not be running. At
(motor negative)
full throttle the status LED should be solid green and
the motor running full speed. At full brakes the status
LED should be flickering green or solid green and the
motor should not be running.
NOTE: If the motor runs when the brakes are applied and
stops when the throttle is pulled, change the
CHANNEL REVERSING SWITCH
Control Adjustment procedures.
9. SET THE COAST BRAKE AT TRANSMITTER
Adjust the
ter to get more or less coast brake. This is accomplished
by slightly shifting the neutral position. After adjustment
be sure that the status LED is still green at full throttle.
BRAKE LIGHTS
The Explorer speed control is equipped with a built in brake
light circuit that can power two LEDs. A complete brake light
accessory kit is available from Novak (kit #5655) and includes
two high power LEDs, two brake light mounting brackets that
allow mounting to most any vertical or horizontal surface of
the car (including inside the tail light area of the body), double-
sided tape, and wiring.
To connect brake lights to the Explorer Sport:
1. Strip about 1/8" of insulation off of both the red and the
black small (26 gauge) wires that exit the back of the
speed control along with the battery and motor wires.
2. Strip about 1/8" of insulation off both ends of the small (26
gauge) extension wires that are the correct length to reach
the position that the brake light is mounted.
3. Solder extension wires onto the brake light wires from the
Mount switch
where it will be
speed control. If two LEDs are to be used, then solder two
easy to get to.
extension wires to each brake light wire from the speed
control. Insulate solder joints with heat shrink tubing.
4. Solder the end of the extension wire from the black brake
light wire to the lead on the notched or flat side of the LED.
Solder the end of the extension wire from the red brake
light wire to the other lead of the LED. Insulate solder joints
with heat shrink tubing.
switch to the
position.
ON/OFF
ON
pot on the speed control until the
NEUTRAL
turns solid red .
LED
pot on speed control until the status
pot is adjusted too high you will
HIGH SPEED
,
EPA
, or
ATL
adjustment on the transmit-
LOW ATV
,
EPA
, or
ATL
on the transmitter is
position and repeat the Speed
on the transmit-
THROTTLE CHANNEL TRIM
TROUBLE-SHOOTING GUIDE
This section describes possible speed control problems,
causes, and solutions.
Steering Channel Works But Motor Will Not Run
• Speed control has thermally shut down––Allow ESC to
cool down––Use milder motor or smaller pinion gear.
• Check motor connections. Check motor and brushes.
• Make sure ESC is plugged into the throttle channel of
receiver. Check throttle channel operation with a servo.
Check wiring color sequence of receiver signal harness.
• Possible internal damage––Refer to Service Procedures.
Receiver Glitches/Throttle Stutters During Acceleration
• Motor capacitors broken or missing––Refer to Step 4.
• Receiver or antenna too close to speed control, power
wires, battery, or motor––Refer to Step 3.
• Bad connections––Check wiring and connectors.
• Excessive current to motor––Use a milder motor or a
to
smaller pinion gear.
Motor and Steering Servo Do Not Work
to position
• Check wires, receiver signal harness wiring and color
sequence, radio system, crystals, battery and motor
connectors, and battery pack.
• Possible internal damage––Refer to Service Procedures.
Model Runs Slowly / Slow Acceleration
• Check motor and battery connectors––Replace if needed.
• Bad battery or motor––Check operation with another.
• Incorrect transmitter or speed control adjustment––
Refer to Steps 5 and 6.
• Optional external Schottky diode (if used) installed
backwards or damaged––Refer to Step 4.
Motor Runs Backwards
• Motor wired backwards––Check wiring and reverse.
• Battery pack wired backwards––Check polarity.
ESC Is Melted Or Burnt/ESC Runs With Switch Off
• Internal damage––Refer to Service Procedures.
*For more help call our Customer Service Department.
SERVICE PROCEDURES
Before sending in your Explorer for service, review the
Trouble-Shooting guide and the instructions. The ESC
may appear to have failed when other problems exist.
PLEASE NOTE: Speed controls that operate normally
when received will be charged a minimum service fee
and return shipping costs.
WHAT TO SEND: Fill out all of the information requested
on the enclosed ESC SERVICE CARD and return it with
your speed control.
WARRANTY WORK: For warranty work, you MUST CLAIM
WARRANTY on the ESC SERVICE CARD and include a
valid cash register receipt with purchase date on it, or an
invoice from previous service work. If warranty provisions
have been voided there will be a service charge.
SERVICE COSTS: Customer is responsible for all service
costs (parts, labor, and shipping/handling charges).
Speed controls returned UPS/COD CASH ONLY. See ESC
SERVICE CARD for other payment and shipping options.
ADDITIONAL NOTES:
• Hobby dealers or distributors are not authorized to
replace speed controls thought to be defective.
• If a hobby dealer returns your speed control for service,
submit a completed ESC SERVICE CARD to the dealer
and make sure it is included with the speed control.
• To provide the most efficient service possible to our
customers, it is not our policy to contact customers by
phone or mail.
• Novak Electronics, Inc. does not make any electronic
components (transistors, resistors, etc.) available for sale.
PRODUCT WARRANTY
Novak Electronics, Inc. guarantees the Explorer Sport to be free
from defects in materials and workmanship for a period of 90
days from original date of purchase (verified by dated, itemized
THROTTLE
sales receipt). Warranty does not cover incorrect installation,
components worn by use, damage from using less than 6 or
more than 7 cells (1.2 volts DC/cell) input voltage, short-circuit-
(optional)
ing heat sinks, cross-connection of battery/motor, damage from
rotating pots beyond endpoints, damage from incorrect instal-
lation of FET servo or receiver battery pack, damage from exces-
sive force while installing heat sinks or adjusting pots, not install-
ing three 0.1µF (50V) capacitors on motor, splices to switch or
receiver signal harnesses, damage from disassembling case,
tampering with internal electronics, allowing water, moisture, or
any other foreign material to enter ESC or get onto PC board,
incorrect installation of alternate input plug plastic, allowing ex-
posed wiring to short-circuit, or any damage caused by a crash.
In no case shall our liability exceed product's original cost. We
reserve the right to modify warranty provisions without notice.
Because Novak Electronics, Inc. has no control over connection
and use of the ESC, no liability may be assumed nor will be ac-
cepted for damage resulting from the use of this product. Every
ESC is thoroughly tested and cycled before leaving our facility
and is, therefore, considered operational. By the act of connect-
ing/operating ESC, the user accepts all resulting liability.
CUSTOMER SERVICE
CUSTOMER SERVICE HOURS (PST)
Monday-Friday:
(714) 833-8873 • FAX (714) 833-1631
©1995 Novak Electronics, Inc. • All Rights Reserved
No part of these operating instructions may be reproduced without
the written permission of Novak Electronics, Inc.
All Novak speed controls are designed and manufactured in the U.S.A.
Explorer Sport™, Polar Drive Technology™, Solid State RVP™, and
Input Plug System™ are all trademarks of Novak Electronics, Inc.
Printed in the U.S.A. 12/95 • #IM-1900-1
8:00am-4:00pm
Hide quick links:
Advertisement
