Table of Contents
Advertisement
Quick Links
Remote Control Car Starter Installation Manual for Model # 28623T
Congratulations on your purchase of the AutoCommand
by remote control from the comfort of your home or office in order to cool it down in the summer or heat it up in the winter.
®
AutoCommand
OEM Series is for automatic transmission/fuel injected vehicles only. It is an extremely sophisticated system with multiple built-in safety and security
features.
• Will start your car by remote control, and run the heater, defroster, or air
conditioner to warm up or cool down the car.
• Is designed to start the car if it is in park, and only if the hood is closed.
• Will attempt to start the car for up to six seconds, but no longer (to avoid
damage to the starter motor). Should the car not start, or if it stalls after
starting, the remote starter will make two further attempts to start it.
• Will not let the car be driven without the key in the ignition.
• Shuts itself off automatically after 10 or 15 minutes (programmable) if
you forget to come out to your car.
• Will shut off if the brake pedal is pushed, the hood is opened, or the
transmission is shifted out of park - unless the key is in the ignition and
in the "run" position.
Tools required to install the AutoCommand
Wire Cutters/Strippers
Soldering Iron
Pliers
Test meter
We highly recommend that all connections be soldered for reliability.
Parts List included with the AutoCommand
Remote Starter
Receiver Module
Antenna
Control Harness
(10 position)
The following parts are included in the plastic bag:
Alcohol Pad
Alchohol
Pad
Green 30 A Fuse
On/Off Control Switch
Warning Label
2 Protected by
DesignTech Labels
© 2005 Directed Electronics, Inc.
www.designtech-intl.com • www.directed.com • 800-876-0800
PLEASE READ COMPLETELY BEFORE BEGINNING
®
OEM Series Remote Car Starter. The AutoCommand
AutoCommand
®
OEM Series Car Starter:
®
OEM Series Unit:
Electrical Tape
Screwdriver
Drill with1/4"and 5/16"
drill bits
®
OEM Series Unit:
Transmitters
6 Power and Ignition wires
Ring Terminal
Hood Pin Switch Set
2 Cable Ties
Yellow Butt Connector
OEM S
®
OEM Series Remote Car Starter system allows you to start the car
• Allows you to remove the key while leaving the car running with the doors
locked for up to 10 or 15 minutes utilizing the Quick Stop™ Option. (See
Separate User Tip Sheet)
• Starts the car automatically whenever the temperature drops below
0
°
F (-18
°
C), or if the battery voltage drops below 11 volts when the
Cold Start™ Option is used. (See Separate User Tip Sheet)
• Has the "Daily Start™" feature which allows the vehicle to be started
at the same time the following day. (See Separate User Tip Sheet)
• Is quality engineered and microprocessor controlled to provide many
years of reliable use.
• Comes with a Limited Lifetime Warranty.
* For free vehicle specific wire information, consult
our website at www.designtech-intl.com
1
ERIES
Wiring Diagram
v5.3 S28623
Advertisement
Table of Contents
Related Manuals for AutoCommand 28623T
Summary of Contents for AutoCommand 28623T
- Page 1 Remote Control Car Starter Installation Manual for Model # 28623T Congratulations on your purchase of the AutoCommand by remote control from the comfort of your home or office in order to cool it down in the summer or heat it up in the winter.
-
Page 2: Installation Instructions
Note: In some cars, the ignition must be in the “on” position to test the power in the brake wire. To Alarm To Remote Starter How to share a hood pin switch with an alarm © 2005 Directed Electronics, Inc. -
Page 3: Optional Steps
H. Watch the red LED light. It will come on after 3 or 4 seconds, indicating that the tach idle rate has been learned. © 2005 Directed Electronics, Inc. I. Watch that the LED light remains on as the vehicle is running and turns off when you rev the engine RPMs to twice the idle rate. - Page 4 15 Min. Run Time Extended Crank IGN 2 not active during crank Ignore Voltage Metering Diesel vehicles No “Enable” Daytime Running Lights Diesel “Wait to Start” 0.45 sec. Alarm disarm pulse Double Input to trigger start © 2005 Directed Electronics, Inc.
-
Page 5: Special Cases
When you are at the feature level you desire, push the start button on the transmitter for one second and the red LED light will flash once to signify © 2005 Directed Electronics, Inc. you are at the Option setting. You can push the transmitter button again and it will flash twice to signify you are at the Factory setting. - Page 6 Toyota Land Cruiser 98+ ... Transponder Toyota Solara 99 + ... Transponder Toyota Supra 98+ ... Transponder Volkswagen Beetle 98+ ... Transponder Volkswagen Golf 98+ ... Transponder Volkswagen Passat 98+ ... Transponder Volvo (all 98+) ... Transponder © 2005 Directed Electronics, Inc.
- Page 7 As with any aftermarket installation, please research and learn as much as you can about the vehicle before you start the install. Instructions, technical tips and detailed wiring information is available on www.designtech-intl.com. Please refer to the information on the website before starting ANY install or call Directed Electronics Technical Support at (800) 876-0800.
- Page 8 The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, DIRECTED is ISO 9001 registered.
-
Page 11: Troubleshooting Guide
If you still get code 12, one of the toggle switch wires may have touched ground, possibly damaging the unit. Or maybe the switch was just turned off while it was running. Or maybe a defective switch? © 2005 Directed Electronics, Inc. Trouble-Shooting Guide... - Page 12 My 5 button remote will not control lock/unlock individually. © 2005 Directed Electronics, Inc. Vehicle_______________________________ PINK (hot in run and start) WHITE or PINK/WHITE (hot in run and start) ORANGE (hot in run only)
- Page 13 Likewise, if the vehicle requires a ground capable of more than 400ma you would need to use a relay. See Installation Note 111, Basic Uses of the Relay from our web site or our Fax On Demand. © 2005 Directed Electronics, Inc. (or 3 ) ignition wire or the accessory wire is not hooked up.
- Page 14 Use the second marker to make a check when you have completed the step in the vehicle. This will help to make sure you have completed all steps, and that you have not missed any features the unit offers. © 2005 Directed Electronics, Inc. Some General Comments:...