Download
Share
Print this page
Minolta SRT 101 Service Manual
  1. Manuals
  2. Brands
  3. Minolta Manuals
  4. Digital Camera
  5. SR-T 101
  6. Service manual
Minolta SRT 101 Service Manual

Minolta SRT 101 Service Manual

Hide thumbs Also See for SRT 101:

Advertisement

Quick Links

Download this manual
MINOLTA
101
•e
minol+a
SRTIOI
SERVICE
MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the SRT 101 and is the answer not in the manual?

Questions and answers

Related Manuals for Minolta SRT 101

Summary of Contents for Minolta SRT 101

  • Page 1 MINOLTA •e minol+a SRTIOI SERVICE MANUAL...
  • Page 2 Assembly and Mounting Mounting of Top cover Mounting of Bottom cover Assembly and mounting of Viewfinder and meter block Mounting of Self-gear and Mirror box Mounting of Front base frame Mounting of Following base plate Mounting of Aperture reducing base plate Mounting of Shutter base plate-A and slow-gear Mounting of Winding base plate Mounting of Film take-up spool...
  • Page 3 DISASSEMBLYSECTION...
  • Page 4 Fig. I 831- 2151 53set 2005 2155 3171 3158 3355set W-28 (01--Q2 3155set 3353 1004set B21-l.7X3 SR T 101 31 53 3159 9151 3354 1005set 31— 7 x 3...
  • Page 5 Dismounting cover Take front cover index on the front frame. Pull out the rewinding knob(3355 set) so as to open the back cover and insert the fulcrum point of a pincette into a slot in the rewinding shaft (3354) so as to unscrew and take out the rewinding knob (3355 set).
  • Page 6 Dismounting View-finder, Meter block Take out the top cover. (See P. 5) Disconnect the soldered portions of the wires (white and orange colored) of the wire print plate (4265) of the roof portion of the pentagon prism. Disconnect the soldered portion of the læd wire(black colored) of the wire cord lug plate (4275)
  • Page 7 Dismounting Front base frame Disrnantle the viewfinder, meter block. (See P. 6) Take out the charge lever setscrew(9106) from the front side of the æmera body andthe self-timer charge lever (2438) and the self-timer bush (2437). Peel off the front lather-A(1071A) and the front leather-B(1071B) .
  • Page 8 Disassembly of View—finder Meter block Dismantle the viewfinder, meter block. (See P. 6) Disconnect the prism pressure support spring(5072) which is engaged with the prism pressure spring (5069). Loosen and take out the and then take out the pressure spring(5069) and the pentagon prism (5803 set).
  • Page 9 Dismounting of Self—timer gear Mirror Disrnantle the front base frame(See P. 7). Loosenand take out three X 3.5) soas to take out the self-timer gar(2491). Take out the lock button (1075). Take out four bayonet setscrews(9152) so as to take out the tnyonet(1061), and then take out from the slot of the Izck of the aperture coupling ring(1063), the AV coupling string(4080) so as to take out the coupling ring (1063 set) .
  • Page 10 Dismounting of Needle following base plate Dismount the top cover (See P. 5). Attach to the rewinding shaft the TV pulley press nut jig take out the AV couplingstring(4080) which is fitted into the slot of the pulley(4Ö68)and disengagethe erne so as to locate it at lateral...
  • Page 11 Dismounting of Aperture reducing base plate Take out the front base frame. (See P. 7). Attach to the rewirxling shaft the rewinding so as to take out the bottom cover. (See P. 5). Expose the bottom of the body and disconnectthe chargelever-B spring(3170), rub plate spring(2580), engagedwith the charge lever-B axis(9052).
  • Page 12 Dismounting of Slow-gear and Shutter base plate-A Take out the top cover. (See P. 5). Loosen and take out two setscrews(B13-l.7X2.5) and take out the slow governor(2391). Take out two frame setscrews(9158) and the eye-piece frame(5061). Take out the TV coupling string(4081).
  • Page 13 Dismounting of Winding base plate Take out the top cover. (See P. 5). Dismount the slow governor. (See P. 12). Take out side the lead wires (white and brown colored) loated in the bended portion of the counter dial stopper(5453) and loosenand take out two setscrews(B21-l.7 so as to take out the stopper unflexing plate(3168) and one dial stopper supporter-A(9107).
  • Page 14 Fig • 9117 E-1.2 2223set 2042set 2162 2041 9117 2047set 2052 9111 9117 BII- 1.7 x 4 2051 9109 2050set 4202set 9223 4291 2110 4276 2112 2 108set 2113 B 19—1.7 XS 3004 4203set 2054 2053 1 set 2213 11-1.7X3...
  • Page 15 Dismounting Shutter base plate-B Dismount the front base frame. (See P. 7). Dismount the slow gear and the shutter base plate A.(See P. 12). Take out the winding base plate and the shutter gear (3004). Take out the bottom cover.(See P. 5). Loosen and take out of the...
  • Page 16 Dismounting Film take-up spool Dismount the slow gear. (See P. 12). Dismount the winding base plate. (See P. 13). Dismount the bottom cover. (See P. 5). Take out the spool shaft nut (9415) from the lower side of the camera body so as to take out the charge Open the back cover and loosen and take out one for the spool...
  • Page 17 Dismounting of Sprocket Disrnantlethe shutter baseplate B. (SeeP. 15). 2. Takeout twosetscrews (9103) o f the middlecontactor b ase(2224) fromthecamer-a body and then the contactor base(2224 set). 3. Takeout from the bottomof the æmerabodythe charge lever—A axis(9006) a ndlet the charge free toward the outside of the amera body.
  • Page 18 Dismounting of Shutter curtains Disrnantle the bottom cover. (See P. 5). Dismantle the front base frame. (See P. 7). Dismantle the shutter base plate—B. (See P. 15). Loosen and take out two B31—I.4X2.5) from the front side of the emera body and then take out the front light shield plate(1026). Exposethe bottom of the camerabody and then disconnectthe solderedportions of the lad wires(two yellow colored oneend red and orange colored,ard for the semi-fixing resistor) of the battery switch isolation plate(4271)and the lead wires(black and blue...
  • Page 19 Dismounting of Lens inner barrel Take out the number ring(1241) and loosenand taken out three Etscrews (B13-I.4X3) so as to take out the filter ring(1235). 2. Take out four inner barrel setscrews(1403) and take out the inner tnrrel(IIIO set) from the outer barrel.
  • Page 20 Disassembly Inner barrel Dismount the front and rar Jens components from the inner barrel(1110 set). Disconnect the pressure(1424) engaged with the operation plate pin(1407) and loosen and take three located around inner tzrrel that the press barrel holder(1115) rnay be taken out from the inner barrel(1110).. Then, take out the diaphragm press barrel(1112),...
  • Page 21 Disassmbly Outer barrel Turn the distance ring(1236)andset it to the infinity(oo) position. Then, put to rnark on the betweenthe distancescalering(1236) and the helicoidinner barrel(1231). Loosen and take out three andthen three sale ring set washers (1383)attached to screwsso as to take out the sale ring(1236). Loosenand take out three setscrews(B73—I.4><2) from the rear of the outer barrel so as to take out the bayonet cover (1380).
  • Page 22 WIRING SCHEMATIC DIAGRAM Fig. Blue White Blue Green or Orange Yellow Black...
  • Page 23 REASSEMBLY SECTION...
  • Page 24 831-1.7 X2S 2151 2 153set 2005 Fig. 20 2155 3171 3158 W-28 (Ol—Q2 3355set 55set 3353 1004set B21- 1.7x 3 minol+a s R T 101 3153 3159 9151 set 3354 1005set 831- 1.7 x 3...
  • Page 25 Mounting of Top cover Check point before mounting * Check if the lad wires of the body are kept in order ; • * Check if the eye-piece lens is free from dust or stain. Clean the counter window of the top cover(1004)and install the top cover to the amera body by means Of three Tighten to the rewinding shaft bearing the rewinding seat(3353) and to the rewinding shaft the rewinding knob(3355 set).
  • Page 26 E-O. Fig• 4073 1.7 x 25 91 54 4391 5025set 5072 Bl I-I .7X3 5065 5069 5067 5804 5066 5805 5803set 5064 Fig. 831-1.7x2 9132 5056 4056 Black 9158 4054set 4265 5061 4057 5053 4052 4068 2163 5057 4275 4080...
  • Page 27 Assembly mounting of View-finder Exposure meter block Check point before assembly Fig. 23 * Check if the pentagon prism(5803), the condenser lens Fransel groove (58()4)and the fresnel lens(5805) are free from scratch stain or dust. Fit the fresnel lens(5805) into the condenser holder(5064) 5805 with the portion having on groove of the fresnel being bated downwardly...
  • Page 28 When the adjustment is to be made from the Fig. 25 befinning. turn the adjustment screws about three turns to raise them from their initial positions 9132 9132 where the adjustment screws have been screwed first. Then, start adjustment from such raised positions.
  • Page 29 Engage the connecting string for a pointer (5053) Fig. 21 54 loosen setscrews (BII—1.4X2.5) index position adjuster (2163) on the shutter mount inse plate —A. Then move adjuster (2163) in such a manner 21 63 that screw head setscrew center of the elongated slot of the...
  • Page 30 Look through the view-finder and rotate the joint Fig. Index moving at finder gar(2154) of the shutter Inse plate A so as to actuare the shutter speed irdex(5057) from the numeral phte letters B to 1000 within the view• finder. When the speed index (5057) is actuating in such nunner that it...
  • Page 31 speed of 1000, then loosen two Fig. X2.5) so that the speed index (5057) may be positionedat the screws(BII—1.4X2.5) so that the speed index (5057) rnay de positioned at the lowest position of the spe«i figure plate letter 1000 by adjusting the second curtain spring tube (2063).
  • Page 32 Mounting of Self-gear Mirror Check points before mounting Fig. • Check if the self-timer gar(2491) moves smo- 2432 othly at its end without stopping in the course movement wheh self-timer gear (2491) is equipped with the charge lever(2438) 2491 and rotated in the direction indiated...
  • Page 33 Fig • 2491 1058 1068 1067 1057 5 1 52set 1002set 831-1.7 X 3S 1064 1063set 1006 1075 9152 B 73-17 4080 Withdraw the coupling string (4080) upwardly, and then engage the notch portion of the coupling ring washer (1064) with the projection of the coupling ring stopper (1067). Engage the knot portion of the coupling Fig.
  • Page 34 Check points after mounting * Check if the self-gear actuates correctly. * Check if the coupling string (4080) extending 5135 Fig• backwardly of the base plate (1002 set) actuates lightly and snvothly when coupling string (4080) is lightly pulled back 5117 so as not to bedisengaged from the pulley and when the...
  • Page 35 Assembly Front base frame Check points before assembly * Refer to the check points before and after mounting of the self-time gear and the box. (P. 32). * Check the lad wire for the X terminals of the emera body is placed along in contact with the camera body.
  • Page 36 Release the shutter and push the mirror operation Fig• lever—A (5153) of mirror box to arrow way then hook hook lever plate (5169) operation 5135 lever—A and set free the hook lever plate (5169) also keep the mirror its Clur position.
  • Page 37 Mount the viewfinder and the meter block. (See P. 27). Mountthe windingleverto the winding base plateandthenwind the winding lever. If the mirror is raisedin the courseof winding,the engagement b etweenthe releaselever-B (2503)andthe pre-setlever-B(2505)is not correctly rnadeso that the pre-setlever-B spring (2525)must be strengthened and the releaselever coupling arm(2502)must be bended for adjustment.
  • Page 38 F. Mounting of Following needle base plete Consolidate or place in order the lead wires Fig. 50 as indicated in the figure. Align the elon- Yellow Black gated slot of the bottom of the • rewinding Expcsure meter shaft bearing (3351) of thed needle following Orange plate with the look plate (1151) and embed Blue...
  • Page 39 Attachment of AV and TV strings : Fig• Attach the MC standerd F 1.4/58mm lens to the body bayonet mount and set the diaphragm ring to F4. Then attach the TV pulley press 2158 nut jig to the rewinding shaft. One knot portion of the TV coupling string (4081) is to be inserted into the slot Of the film sensitive ring (2158) of the shutter Inse...
  • Page 40 Fig. 1068 4080 4070set 4074 4073 4069 coupling string (4080): Check if the AV string (4080) extending from the front frame is not disengaged from the middle pulley—A(1068). Engage the AV string (4080) to' the middle pulley band—C (4073, 4074). In this state, insert the AV string(4080) into the slot provided around the AV pulley (4069) of the needle following base plate in the clockwise direction.
  • Page 41 Cam pæition adjustment : Fig• Needle following Loosen adjustring ring(4082) and rotate pulley(4068) in the clockwise direction the adjusting ring (4082) in the counterclock- wise direction that (4080, 4081) tightened. knot portion and the portion inserted in the slot of the AV string(4080) are pasted to hold it in...
  • Page 42 Set temporarily the safety switch holder (4251 set) Fig. •to the needle following tnse plate by two setscrews (BII-1.7X3.3, B13-1.4X2). AV safety terminal adjustment : When taking a photo and depressing the preview button in case of MC Lens (erroneous operation) , the error will be produced except the case when...
  • Page 43 Mounting Aperture setting mount Check point before mounting Fig. 9363 2571 * Make it sure that reducing lever plate spring (2574) of the aperture reducing base plate (2571 set) is bended as illustrated in the figure and that the reducing rub plate (2572) must slide lightly when the rub plate (2572) is rotated in 2574...
  • Page 44 The shutter of the camera body is cocked Fig. and then adjustment must be made so when the reducing rub plate (2572) of the base plate (2571 set) is pushed down once the aperture setting switch becomes "OFF" when pushed down again the switch becomes "ON"...
  • Page 45 Mounting of Shutter base Plate-A Slow gear Check point before mounting Fig. 67 * Check if the gear (2308) Of the slow 2308 governor Wii! eturn to its initial position when part is displaced in the direction indi- ated by the arrow in the figure to its full extent.
  • Page 46 Mount the windinglever to the winding lever holder. Set the shutter base plate—Ato thilb position, and release the shutter. In this ease, if the shutter curtain fails to close or run, this is because the sliding motion of the second shutter curtain lock lever(2029) and the clutch fork (3024) is not smooth, Adjust by bending the bended portion of the clutch fork (3024).
  • Page 47 Shutter speed adjustment Make it sure that the slow governor is not engaged when the shutter is released at such high sl*ed from 1/1000 to 1/60. If the slow goverrur is engaged, adjust by rotating the eccentric pin of the slow adjustment lever (1/8 adjustment) so that the slow gear may not...
  • Page 48 the waist portion of the FP contactor (2220) so as to increase the contact presQxre. Fig. 74 * When switching-in of X time lag is too soon, adjust the contactor distance as is the ase of 2216 FP adjustment. Remove the front frame and widen the distance...
  • Page 49 Mounting of Winding base plate Open the back cover and align the operation nail base plate (3406) of the wind-up base plate (3023 set) with the projection portion of the film spool shaft (3031) ani hold it in position by two sets:rews (B13-2X3.3).
  • Page 50 toward the inside of the camera body, then the stopper (3453) pushes the dial stop pin (9267) so that the ratchet gear (3404) is caused to rotate. When the stop nail (3408) falls tighten the setscrew (B21-1'7 X 3.5) of the into the first tooth of the ratchet gear (3404) ,...
  • Page 51 J. Mounting Film take-up spool Open the back cover and Ipace the decoration ring spring washer (3039) and the spool decoration ring (3037) upon the film spool (3032). In this state. assemble them into camera body. Insert the film spool shaft (3031 set) from the upward of the Gimera body and hold it in such potition where the elongated slot of the film spool(3032) may be facing upwardly.
  • Page 52 Fig. 9117 2223set 2042set 2162 2041 9117 2047set 2052 9111 9117 1.7 x 4 2051 9109 2050set 4202set 9223 4291 2110 W- IS 4276 2112 2 108set 2113 3004 •BIQ- 1.7 x s 2054 4203set 2053 1set 2213 1.7 X3...
  • Page 53 Mounting Of Shutter base plate—B Insert the adjustment washers into the first and Fig. 82 second curtain spring shaft (2060, 2061) and position the first curtain bound stop lever (2101) of the shutter base plate—B(2050 set) a position indicated the figure. the first and second curtain spring 2050set shaft (2060, 2061) into the holes of the shutter...
  • Page 54 wind first shutter curtain axis so that seam Fig. line of the first shutter curtain be aligned with marking-off line. this state, stop your 2042set finger the curtain spring shaft (2060). Insert into the variable gear axis (2045) the variable gear (2041 set) in such a position where the straight...
  • Page 55 dr+'inggearandthesecond s huttercurtaingearsetscrew andwindup afterloosening slighdy the semnd shutter cur-uin gear setscrew. Loosen also the first shutter curtain gear setsaew slightly and hold the semnd shutter curtain shaft in such a manner that the rnarking-off line of the second shutter curtain rnay be seen. Then, loosen the second shutter gear setscrew further so as to rotate the semnd shutter curuin axis.
  • Page 56 Wind up the shutter curtains and open the lnck cover. Then, rotate the sprocket so as to position the sprocket teeth to be directed toward you, and engage the reversing stop nail (3025) into the idle (3003). Also place the projection of the film spool shaft (3031) in the right lateral direction.
  • Page 57 Intermediate check points : Check if the meter needlecomesto rest within the outer periphery of the followingneedle (allowance in ± 0.3 E V) at the following two points. 8 (ASA 100, 1/8 sec., F5.6) EV 11 (ASA 100, 1/60 sec., F5.6) when the meter needle deviatesout of the outer periphery deviate the EV 5 and EV 14 pointsso that the intermediate points may come to rest within the permissadlerange.
  • Page 58 Mounting Shutter curtains Fig. Cheek points before mounting order to check shutter cur- tains are installed in parallel, rotate 2053 2063 first curtain shaft (2053) in the clockwise direction as indicated in the figure wind first Parallel a line shutter curtain also check...
  • Page 59 Mount the counter isolation (4059 set) by two setscrews (9163) and solder Fig • Blue Yellow the lead wire (yellow colored) of the isolation base(4259 set) as illustrated Fit _ in the figure. Insert lead wires (yellow, red, orange and blue colored) 9163 into the openings of the amera body and pull...
  • Page 60 Assembly of Lens inner barrel Set the minumum diameter position determing jig to the inner barrel (1110 set). Lift up slightly the am ring(llil set) and insert the diaphragm operation lever (1374 set) into the operationlever axis(1405) on which the couplingwasher(E-1.9) must be attached. After mounting, hold the interlock pin(1406) of the operation lever (1374 set) so as to checkthe play in the vertial directionand if the play is too much,adjustby insertingthe washer.
  • Page 61 Fig. 1115 Front lens group 1112 1371 11 13set 1407 Bbl- 1.7 X22 1 1 1 Oset 1404 1405 1374 1381 E-1.9 1424 1379 1425 1420 1406 I Iset lens group 1424 Figi 1374set 1406 1420...
  • Page 62 Assembly Outer lens barrel Check points of the outer lens tn.rrel Fig. Check make it sure that the helicoid inner barrel, outer barrel and outer barrel ring (1231, 1232 and 1233) free from scratch 1231 stain. Check make sure that sliding portion of the...
  • Page 63 Fig. 1233 1232 1239set B) 3-1.7x 1375 1427 1429 1 237set 1231 B 13-1.0<5 B13-l.4X3 1383...
  • Page 64 Assembly mounting of Inner barrel Outer lens barrel Secure the inner barrel temporarily by two and contact the arn- the outer barrel by two guide lever setscrews(1417)and set the aperture sale to 16. Aligh the cam ring arm (1385) of the inner barrel with the slot of the diaphragm guide lever (1376) of the outer ler.s barrel, and insert the cam ring aim (1385) into the guide lever (1376).
  • Page 65 Fig. B 73-1.4X2 1430 1380 1431 1422 1240set 1426 1427 1238set 1234 1389 1417 813-1.4x 1386 1239set 1376 Iset 1403 1235 B13-l.4xS 1 24...
  • Page 66 Mounting Sprocket Align with and fit into the slot of the sprocket gear shaft bearing (3048 set) the clutch pin (9123) of the sprocket shaft (3049 set). Mount the sprocket (3046) as in the figure and insert into the hole of the sprocket (3040) the sprocket gear shaft bearing (3048 set) and the sprocket shaft (3049 set) from the upper side of the camera body and hold in position the shaft bearing(3048 set) by two setscrews(B31-1.4X3).
  • Page 67 CROSS SECTION Shutter curtain Filter ring Eyepiece holder Shutter speed scale plate Tripod socket Standard lens Shutter speed needle Auto pre-set Diaphragm ring Lens bayonet mount Condenser lens Meter coupler Lens mount Fresnel lens Pentagon prism Diaphragm blade Fine micro prism Light meter...
  • Page 68 831-1.7 x 2.5 2151 9131 5061 3305 9158 3306 2005 3302 2155 3311 3355 5801 3303 3158 w-28 (0.1—0.2 5802 3312 3156 9377 3353 3155 5062 B21-l.7X 5060 m inol+a SR T 101 3153 1073 3159 9151 . _ 17 / 1 074 1001 1005...
  • Page 69 9387 1 053 1 052 9159 1 059 9380 1 004 m i no 1+0 1 060 3415 1 055 1 054 9452 1 077 1 056 1 072 1 076 9110 4215 4214 9275 9276 4213 1 005 4212 Complete parts.
  • Page 70 831-1.4 4060 w-26 Bl 1-1.4 x 1.6 4051 4082 813-1.7 4068 B) 1-1.7 X 3.3 w-23 4059 4078 9373 4067 w-25 w-27 B13-l.7X3 4069 4275 3351 3354 Complete Parts. Including pares number num ber 4067. 9373. 4067-71...
  • Page 71 E-1.2 9451 9208 9353 4056 4 071 4054 4070 4053 E-0.8 40.74 9351 4252 9355 4254 4052 4057 E-0.8 9388 4 074 4253 9354 4255 4072 4253 4 069 4058 9374 Complete parts lucluding parts number number 9351. 4054-71 4054, 4053.
  • Page 72 BII-l.7X3 5069 4265 4191 5068 5807 5808 9164 E-0.8 5057 5803 5072 BII-l.7X2S 9132 4073 9058 9 1 54 4391 5070 B31-l.7X2.2 9101 5071...
  • Page 73 5063 B) 1-1.4 5030 5055 9367 5054 5073 5056 w-16 5058 5074 5809 5025 5065 5067 5 804 5066 5805 5064 Complete parts. Including parks number number 5025, 5030, 5073, 5074, 5025-71 9367, w-16.
  • Page 74 E-0.8 811-1.7 X2.s 4074 4077 9357 B 19—1.7 X 4.2 4075 9153 2159 2263 819-1.7 x 4.2 9358 B13-1.7X2.5 4017 5059 2391 Complete Parts. Including pares number Key number 4017, 5059, 9358. 2159-71 2159, 4075. 9357. 4077-71 4077.
  • Page 75 2327 2336 2337 2325 2326 2304 2304 2301 2311 2310 2312 2335 2317 2309 2313 2308 2314 2305 2319 2328 2316 2306 2315 2307 2321 2303 2318 2323 2320 2329 2322 2330 2303 2324 2302 2334 2331 2332 2333...
  • Page 76 B! 1-1.7 X2.5 811-1.4 X 2.5 2163 9208 2160 9421 21 54 2020 4081 9147 2158 2021 2156 5053 2157 2017 B) 1-1.4 E-0.8 9207 2033 9206 2031 2014 9204 2013 2018 2016 2049 2015 2023 BII-1.7X3 9209 2028 9224 9210 2024 2029...
  • Page 77 3453 B21-l.7x 9107 9314 B) 3-1 3168 813-2 X 3. B13-2X3.3 3165 Complete parts. Key number Including pare number 3168-71 3168. 3453, 9314.
  • Page 78 9110 3402 3401 3015 3151 3451 3022 9267 3021 9268 3020 3161 3407 9269 3404 9270 E—l.9 3406 3452 9272 813-1.7 X 2.5 9107 "O 3409 3408 31 67 9244 9108 Complete parts. Key number Including parts number 3152, 3408, 3409, 3452, 3160, 3160-71 9269, 9270, 9272, w-2.
  • Page 79 Pa e 13 831-2x4 9148 1071B 1021 E-0.8 1071A 2441 2442 2440 2437 2438 9106...
  • Page 80 2491 e 15 e 14 813-2 x 3.3 1064 1065 1 063 1 006 1061 1 075 673-1.7 4080 Complete parts. Including parts number number 1063, 1065. 1063-71...
  • Page 81 9297 9298 9276 Bl 1-1.7 x 2.3 Bl 1-1.7X 1062 2242 9019 2243 1 007 1 057 2262 5151 5 1 34 9295 5152 1 068 zin* 9356 1 067 Bl 1-1.7 x 2. 1 002 2291 9162 5133 2587 9110 9294 1 058...
  • Page 82 9129 5008 5157 9293 5135 9287 9 1 44 5156 5009 5101 e 17 5013 9284 e 16 9287 9 102 5167 5 1 07 9284 9002 5168 9016 5136 9133 Bl 1—1.7 X 1.9-= 5160 5121 9056 9402 5119 9285 5159 9372...
  • Page 83 9296 5 1 64 9376 5158 5010 5001 5 1 66 5163 512B 9401 9301 5112 5169 9306 B31-1.7X Complete parts. number Including pares number 5001, 5010, 5126, 5158, 5161, 5001-71 5163. 5164, 5166, 9296, 9372, 9376, B31—1.7x2.5 55169, 5112, 9301, 9306.
  • Page 84 9283 9286 5106 9286 9407 5 1 04 9282 9288 9288 5105 51 05 5102 5 1 04 9414 5806 5103 9130 Complete parts. Including parts number number 5102-71 5102, 5104, 5105, 5106, 9282, 9283, 9288, 9414. 5108-71 5108, 9286, 9407.
  • Page 85 9222 E—l.2 2042 9117 9214 2052 2030 813-1.4 9229 9212 9117 9215 4222 2043 2220 9117 2221 2041 2223 2051 2222 2044 2162 2046 9111 BII-l.7X4 2218 2045 9218 2050 9217 2101 2081 21 02 2047 9220 2048 E-1.2 9109 9216 21 07 2109...
  • Page 86 9 1 03 2226 3030 2228 2227 3024 3004 2226 3028 9261 2225 3005 2224 3008 3006 B31-1.4X 3048 3047 91 24 3162 831-1.7*5 9263 3025 WE-2 9141 9128 3 1 64 3040 9124 3163 9127 WE-2 3043 1012 1027 Complete parts.
  • Page 87 4269 9309 4202 9276 3062 4208 4228 3061 4276 4227 9006 4291 x 3.5 9307 819-1.7 4271 3063 4203 31 70 9052 2580 B 19-2 X 4.5 2582 1112 4270 4230 4272 9307 4209 4266 w-21 9383 4204 3169 4205 3157 4206 4269...
  • Page 88 9264 839-1.7 x 2.5 3042 3067 9004 3066 9139 9408 3059 3070 9265 9121 3060 3166 3071 9245 9004 3057 3056 3055 11-1.4X 1017 3053 3051 31-1.4 x 2.5 3050 3058 Complete parts. Including pares number number 3041, 9264. 3041-71 3057-71 3057, 9245.
  • Page 89 4257 4258 9053 4256 1070 4263 e 23 2523 2509 9005 1025 B 10-1.7x3 9241 2074 2073 2559 2073 9390 2075 2507 9 1 04 9105 2525 2508 e 23 e 29 9105 9242 1 029 2511 9235 2567 9403 2557 9405 2551...
  • Page 90 9301 2562 2563 2503 9309 9362 2558 2552 9310 2559 2553 9361 9371 2 564 2 5 54 9234 Complete parts. Including parts number 2558, 2552, 2514, 2553, 2554. 2552—71 9361, 2559. 9234, 9307, 9310. 9362, 9371. w—7. 2563, 2503, 2562, 9301, 93040,...
  • Page 91 3049 9202 9123 3039 3037 3046 839-1.7.X3 e 26 e 27 e 27 3031 B21-l.7X B51-l.7X...
  • Page 92 B39-1.7x 1151 1019 2254 9112 2247 2246 2245 e 28 e 28 e 27 2213 BII-1.7X3 831-1.4 X2.s 1026 Complete parts. Key number Including parts number 2246-71 2246, 2245, 2247.
  • Page 93 1 123 1 126 1 125 1 124 1101 9331 9203 9201 1127 1 106 1110 1 105 9299 1 107 9332 1 103 9203 1 104 Complete parts. Including parts number number 1105, 1106, 1107, 1109, 1101, 1101-71 1118, 1123, 1124, 1125, 1110, 1127, 9201, 9203, 9331.
  • Page 94 3052 B21-1.7X 3046 3032 3036 w-17 9283 3035 3038 2211 3033 2217 9262 9276 Complete parts. lucluding pares number number 2211, 2215, 2217. 9276b, 2211-71 9283. 3038, 9262. 3038-71...
  • Page 95 2064 2070B W—19 2069 2083 w-lO(O.1t E—I.S 2059 w-10(O.2t) 2064 B31—l.4X 2070A 2056 2077 2079 B31-1.4X3.S 2078 2055. 2063 2083 2066 2054 w-10(O.2t) 2061 2067 2062 2065 2060 2077 2079 2053 2069 2078 W—19 2055 E-I.S B31-l.4X Cmplote parts. Including parts number number...
  • Page 96 9384 9385 9386 9375 9163 2579 4273 2578 2571 4222 9384 4260 2572 4222 9364 2161 9363 4222 2573 9359 4262 9379 4259 2574 9205 2576 2072 2577 2581 2575 9369 9366 Complete parts. Including parts number numer 2573, 2574, 2575, 2571-71 2571,...