Related Manuals for Assmann DIGITUS OnLine DN-170093
Summary of Contents for Assmann DIGITUS OnLine DN-170093
- Page 1 ONLINE UPS SYSTEM DN-170093 Rev. 4・DN-170094 Rev. 4 DN-170095 Rev. 4・DN-170096 Rev. 4 Quick Installation Guide...
- Page 2 1. Important safety warning Important safety instructions – Save these instructions Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully.
- Page 3 The ups should reserve sufficient heat dissipation channels and be careful not to • let other objects block the front and rear panels. It's recommended to leave at least 50cm space in front and back of the UPS for heat dissipation. 1.4 Operation Do not disconnect the mains cable on the UPS system or the building wiring outlet (shockproof socket outlet) during operations since this would cancel the...
- Page 4 Do not dismantle the UPS system. 1.6 Symbols used in this guide CAUTION! Read this information to avoid equipment damage 2. Installation and setup Note: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. Please keep the original package in a safe place for future use. 2.1 Unpack checking Don’t lean the UPS when moving it out from the packaging Check the appearance to see if the UPS is damaged or not during the...
- Page 5 1.5 kVA: 2 kVA: 3 kVA: (1) Output receptacles (10 A) (6) AC input receptacle (2) Battery terminal (7) Input circuit breaker (3) SNMP intelligent slot (8) EPO (with Jumper cap) (4) RJ45 Surge Protection (9) USB (5) RS-232 communication port (10) Output receptacle (16 A) Note: If EPO is not used, do not remove the jumper cap.
- Page 6 2.3 Installing the UPS • Rackmount installation The UPS is supplied with 19-inch mounting brackets for installation in the server rack. Mounting rails must be ordered separately (part number DN-170109). Please refer to user manual for detail installation. • Rackmount converted to tower installation (1) Two plastic base brackets (2) Flatten it after intercrossing Intercross as following figure:...
- Page 7 CAUTION A small amount of arcing may occur when connecting the internal batteries. This is normal and will not harm personnel. Connect the cables quickly and firmly. b) Connect the internal battery connector (see Figure 2). Connect red to red, Press the connector tightly together to ensure a proper connection.
- Page 8 2.4 Setup the UPS Step 1: UPS input connection Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords. • For 208/220/230/240VAC models: The power cord is supplied in the UPS package Step 2: UPS output connection •...
- Page 9 Operation and display panel ① ② ③ ① LED (from right to left: “alarm”, “bypass”, “battery”, “inverter”) ② On-Line UPS LCD display ③ Function keys...
- Page 10 LED indicator Indicator Description ON: The UPS has an active alarm or fault The UPS is in Bypass mode. ON: The UPS is operating normally on Yellow bypass during High Efficiency operation. ON: The UPS is in Battery mode. Yellow ON: The UPS is operating normally.
- Page 11 • Switch to UPS self-test mode: Press and hold this button for 2 seconds to enter UPS self-testing while in AC mode • Turn off the UPS: Press and hold this button at least 2 seconds to turn off the UPS in battery mode. UPS will be in standby mode under power normal or transfer to OFF/ESC Bypass mode if the Bypass enable setting by pressing this...
- Page 12 This is a Class C2 product. In home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures. Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
Need help?
Do you have a question about the DIGITUS OnLine DN-170093 and is the answer not in the manual?
Questions and answers