Fitting The 1805Fi Custom Door Panel - Asko 1325 Installation Instructions Manual

FITTING THE FITTING FITTING THE 1805FI THE THE
FITTING FITTING THE
The 1805FI can only be installed with a custom door
panel that extends from the toe kick to the counter top.
The unit comes with everything needed to make
installing the door panel easy. The door is predrilled for
the panel's mounting screws.
The custom panel should be at least 1/4" thick.
ITEMS PRO O O O O VIDED ITEMS PR ITEMS PR VIDED VIDED
ITEMS PR ITEMS PR VIDED VIDED WITH
Two 3/8" screws (B)
One protective tape (C)
Four adhesive-backed plastic spacer washers (D)
Four 1-3/4" screws (G)
INST INSTALLING INST INST INST ALLING ALLING THE CUST ALLING ALLING THE CUSTOM P THE CUST THE CUST THE CUST
Before fitting the custom panel, the dishwasher must
be installed underneath the cabinet. After you've made
the required measurements, pull the machine out again
to install the panel.
Refer to the illustration at right for instruction references.
1. Fit the handle (A) onto the panel according to the
manufacturer's instructions. ( NOTE: A handle
should be used rather than a knob, because a knob
does not provide enough grip.)
2. Peel the adhesive backing off the washers and place
them in line with the four keyholes (C) on the metal
front of the dishwasher door.
3. Loosen the screws (D) on the outer edges of the
dishwasher door.
4. Pull the turbo fan exhaust frame (E) down until the
lower edge aligns with the lower edge of the cabinets
and tighten the screws. Next, snap the plastic duct
into the turbo fan exhaust vent.
WARNING!
The custom panel must not
obstruct the turbo fan exhaust.
See step 4 above for instructions
on how to adjust the fan exhaust.
5. The two short screws (B) go into the back of the
panel, 16-3/16" from the upper edge of the panel
and 5/8" from the outer edges. Insert the short
screws into the panel, leaving 1/8" of space between
the screw head and the panel.
6. Hook the panel screws (F) into the keyholes (C) on
the dishwasher door.
7. Push the panel upwards until the lower edge aligns
with the lower edge of the cabinets.
NOTE: The custom panel should not extend more
than 2-15/16" below the bottom of the dishwasher
door. Otherwise, it will strike the toe kick and
damage the machine and/or the panel.
8. Open the door and tighten the screws (F) inside.
9. Remove the backing from the protective tape and
apply it on the bottom edge of the panel, in front of
the exhaust vent.
Page 10
1805FI CUST 1805FI 1805FI CUST CUST CUSTOM DOOR P OM DOOR P OM DOOR P OM DOOR PANEL
1805FI CUST OM DOOR P
WITH WITH THE UNIT THE UNIT
WITH WITH THE UNIT THE UNIT THE UNIT
OM P OM PANEL OM P OM P ANEL ANEL ANEL ANEL
ANEL ANEL ANEL
ANEL
CUST CUST OM P OM P ANEL DIMENSIONS ANEL DIMENSIONS
CUST CUSTOM P CUST OM P OM PANEL DIMENSIONS ANEL DIMENSIONS ANEL DIMENSIONS
Width: 23-3/8" (597 mm)
Height: 28-1/8"–30-1/8" (714 mm–765 mm)
(Measured from the top of the panel to
the lower edge of the kitchen cabinet.)
Thickness: 1/4" (25 mm)
Weight: Up to 22 lb.
NOTE: Specifications subject to change without
notice.
NOTE: Heavy-duty door springs can be purchased for
wooden door panels weighing over twelve
pounds. (P/N 8071323-77).
Installing the 1805FI Custom Panel
ADJUSTING THE DOOR SPRINGS ADJUSTING THE DOOR SPRINGS ADJUSTING THE DOOR SPRINGS
ADJUSTING THE DOOR SPRINGS ADJUSTING THE DOOR SPRINGS
After you install the custom panel,
make sure the door can be
opened at any angle. If it tends to
fall down, pull out the machine
and tension the door springs on
the sides of the machine by
moving them one hole farther
back or by twisting the spring to
make it shorter. If that doesn't resolve the problem, you
may need to purchase the heavy-duty door springs (Part
Number 8071323-77).
FASTENING THE DISHWASHER FASTENING THE DISHWASHER FASTENING THE DISHWASHER FASTENING THE DISHWASHER FASTENING THE DISHWASHER
TO THE CABINET TO THE CABINET TO THE CABINET
TO THE CABINET TO THE CABINET
Refer to page 8.