Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION G40P
Summary of Contents for HIKVISION G40P
- Page 1 AE-DI5052-G40 PRO Installation Guide...
- Page 2 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings © 2020 Hangzhou Hikauto Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikauto Technology Co., Ltd. or its affiliates (hereinafter referred to as "Hikauto"), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikauto.
- Page 3 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS.
-
Page 4: Symbol Convention
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Symbol Convention The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. -
Page 5: Table Of Contents
Chapter 5 Upgrade and FAQs ......................34 5.1 What should I do when the mobile phone cannot connect to the device hotspot? ..... 34 5.2 Upgrade the G40P Device by TF Card (Automatically delete the update package after deletion) ........................... 34... - Page 6 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 5.4 Upgrade the G40P Device in Batch by TF Card ..............35...
-
Page 7: Chapter 1 Preparation
Before the installation, get familiar with the aspects closely related to the construction site, such as installation location, the vehicle model, the selection of the installation location of the G40P device and the camera, cable length, tools, to make sure the installation and debugging go well. - Page 8 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Tool Function Requirements Picture Illustration Wire Stripper Strips electrical insulation from wires. Electro probe Detects the electrical wires. General type Straight/Cross Opens the center console. Length: approx. 20 cm Screwdriver...
- Page 9 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 4G SIM Card Used platform Nano-SIM Card. communication. Requires an Purchase the SIM card industry SIM card. before installation. Hexagon Used to open/close the SIM The G40P comes with screwdriver this accessory out of card and TF card slots.
-
Page 10: Device Preparation
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 1.3 Device Preparation Device Model Picture Illustration G40P Dashcam AE-DI5052-G40 Pro TF Card (Supports dual AE-MW3TF1(TLC/128G)(B) TF cards) Side Camera AE-VC236T(1.0mm) (Optional) Side Camera AE-VC236T(1.0mm) (Optional) Rear AE-VC253T-IT(2.8mm) Camera(Optional) Wired Alarm Button AE-IFC00(O-STD)(cable alarm)(2.5m) -
Page 11: Requirements For Installation
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 1.4 Requirements for Installation Install and debug the intelligent terminal by strictly following the instructions below to improve the device stability and ensure the terminal delivery. Consider the following aspects when selecting the installation location and methods. -
Page 12: Chapter 2 Installation
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Chapter 2 Installation 2.1 Connect Cables to Device 2.1.1ConnecttoMainBundle Identify Cables Identify the function of each cable before connection. Color Definition VCC Cable(Power Cord) Orange ACC Signal Cable Black Ground... - Page 13 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Black Connects to Device Power Interface Find the power supply Step 1 Find the vehicle signal cables: power anode, power cathode (ground), and ignition signal (ACC ON). Step 2 Use the electro probe to test whether the cable is powered after turning off the vehicle. If the current is detected, this cable is connected to constant power and then you can test the voltage.
- Page 14 Step 1 Pull the power cord out gently from the fuse box and lead the cable up along the A pillar. Step 2 Route the cable closely along the windshield and connect it to the G40P device. Step 3 Hide the cable on the vehicle roof.
-
Page 15: Connect To Device
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 2.1.2 Connect to Device There are five cables extended from the G40P device. Identify the cable function from the following table. Label Interface Function 16-pin male plug-in Connects to G40P. -
Page 16: Install Device
IOS & Android Steps: Step 1 Make sure the power supply of the G40P is disconnected, insert the TF card and SIM card, then use the 6-pin screws to tighten the cover. When you use the TF card for the first time, insert the TF card into the device and format the card on the app. - Page 17 Dash12345. The app jumps to the main interface after Wi-Fi is connected. When G40P is connected to the mobile phone APP for the first time after leaving the factory, you need to activate the device and reset the password. After completing the password reset, you need...
- Page 18 Settings Step 3 Go to Settings > Smart Settings > ADAS Settings > Camera Settings > Hidden Line, and adjust the mounting position of G40P on the windshield and the bracket angle according to the imaging effect on the APP.
- Page 19 Step 4 Tighten the bracket knob. Step 5 Select a device installation location. Normally, the G40P terminal is installed on the center of the front windshield. To make sure that the picture is as unobstructed as possible by the wipers after installation, use a watering can and a rag to wipe the windshield clean.
-
Page 20: 2Install Side View Camera And Adjust Angle
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 2.2.2Install Side view Camera and Adjust Angle Step 1 Install the side view camera on the left and right sides of the truck compartment as shown in the figure below, and complete the wiring. - Page 21 Step 3 Connect the left and right cameras to the CH3 and CH4 ports of the extended harness. Step 4 Make sure the power supply of the G40P is disconnected, and plug the expansion harness into the interface of the G40P...
-
Page 22: Install Rear View Camera And Adjust Angle
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Step 5 Power on the G40P, connect the G40P with the mobile app, and check the side-view camera image. 2.2.3 Install Rear View Camera and Adjust Angle Step 1 Install the rear view camera on the rear of the vehicle as shown in the figure below, and... - Page 23 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Step 2 Connect the rear cameras to the CH5 ports of the extended harness.
- Page 24 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Step 3 Make sure the power supply of the G40P is disconnected, and plug the expansion harness into the interface of the G40P Step 4 Power on the G40P, connect the G40P with the mobile app, and check the rear-view camera...
-
Page 25: Chapter 3 Function Settings
3.1 Smart settings 3.1.1 ADAS Settings ADAS function is realized by the built-in camera of the G40P device. Set the camera before using the ADAS function. Step 1 Run the app and go to Settings > Smart Settings > ADAS Settings > Camera Settings. - Page 26 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Step 3 Calibrate hidden line (1) Go to Settings > Smart Settings > ADAS Settings > Camera Settings>Hidden Line, start calibration. (2) Click Tutorial to view the calibration introduction. Follow the instructions to adjust the camera angle to align the blue horizontal line with the horizon.
- Page 27 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings (3)Make sure the intersection of the lane and the horizon coincides with the center point. You can click the Move button to manually adjust the position of the center point in the box.
- Page 28 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings PCW events are different from other events, an alarm will only be triggered when the vehicle speed is below the configured lowest speed threshold.
-
Page 29: Dsm Settings
Sensitivity: The higher the sensitivity is, the more easily the alarm will be triggered. 3.1.3 VSD Settings The VSD (Vehicle status Detection) alarms of G40P device supports include Rapid acceleration, Rapid deceleration, Take a sudden turn, and etc. You can set these alarms in the app: Settings > Smart Settings >... - Page 30 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings...
-
Page 31: Image Video
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 3.2 Image Video You can set configuration parameters, such as audio and video codecs. Convenient Settings: You can set the sensitivity to trigger the overspeed alarm. The higher the sensitivity is, the more easily the alarm will be triggered. -
Page 32: System Maintenance
Delayed shutdown time: Can set the shutdown delay time, the device can still continue to work normally after the vehicle is turned off G-Sensor Emergency Recording: When turned on, the G40P will automatically wake up when the vehicle is collided while the ignition is off. - Page 33 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings...
-
Page 34: Format The Tf Card
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings 3.3.1 Format the TF card Step 1 Insert the TF card and go to System Maintenance>Storage on the app. Step 2 Click the Memory Card Formatting button and click Yes in the pop-up window to start... -
Page 35: Network Parameters
At the beginning of formatting, G40P will send out a voice prompt, and a buffered pop-up window will appear on the APP interface; at the end of formatting, the G40P will give a voice prompt Except for the first time to insert the TF card, it is not recommended to format it again during normal use, otherwise it will cause the video to be lost and cannot be recovered 3.4 Network Parameters... -
Page 36: Chapter 4 Platform Settings
Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Chapter 4 Platform Settings 4.1 Configure ISUP5.0 platform parameters on the device Connect the APP to enter the configuration interface; Go to Settings > Platform Config > ISUP5.0 Platform Enable the Platform Enabled startup function;... - Page 37 Mobile Video Recorder (G40P) • Installation Guide and Platform Settings Configure storage information Open the Picture Storage button and select the corresponding storage device; After configuration is completed, the online status of the device can be seen in the Device>Device and Server>On board Device of HCP;...
-
Page 38: Chapter 5 Upgrade And Faqs
Step 1 Insert the TF card used for upgrade into the G40P device and format the TF card on the app. Step 2 After the TF card can record normally (REC blue light on the device is always on), remove the TF card. - Page 39 (1) Follow step 1 and step 2 in 5.2 to format the TF card. Skip the first two steps in 5.2 if the TF card can record videos normally on the G40P device. (2) Extract the package and rename the digicap.dav file as digicap_FACTORY_BACK_DOOR and put the file in the root directory of the TF card.
Need help?
Do you have a question about the G40P and is the answer not in the manual?
Questions and answers