Diamond D3 1000.1 Installation Manual page 3

Frequency Response:
Signal to Noise Ratio:
Channel Separation
THD+N(Total Harmonic Distortion + Noise)
RCA Input Sensitivity:
RCA Input Impedance:
Min to Max Voltage requirements
High/Low Pass Crossover:
Crossover Configuration:
Bass EQ
Frequency Response:
Signal to Noise Ratio:
Channel Separation
THD+N(Total Harmonic Distortion + Noise)
RCA Input Sensitivity:
RCA Input Impedance:
Min to Max Voltage requirements
High/Low Pass Crossover:
Crossover Configuration:
Bass EQ
Frequency Response:
Signal to Noise Ratio:
Channel Separation
THD+N(Total Harmonic Distortion + Noise)
RCA Input Sensitivity:
RCA Input Impedance:
Min to Max Voltage requirements
Low Pass Crossover:
Crossover Configuration:
Bass EQ
Frequency Response:
Signal to Noise Ratio:
THD+N(Total Harmonic Distortion + Noise)
RCA Input Sensitivity:
RCA Input Impedance:
Min to Max Voltage requirements
Low Pass Crossover:
Crossover Configuration:
Bass EQ
20Hz to 20KHz +/-3 dB
>95dBA (20 to 20kHz)
50dB
<0.2% (Output-1W 4 Ohms)
150mV to 4V
>20K Ohms
10.2V to 15.5V DC
12dB/Oct, 30-500Hz Variable
Switchable (OFF/HP/LP)
0 to 12dB @ 50Hz (Variable)
20Hz to 20KHz +/-3 dB
>90dBA (20 to 20kHz)
50dB
<0.2% (Output-1W 4 Ohms)
150mV to 4V
>20K Ohms
10.2V to 15.5V DC
12dB/Oct, 40-400 Variable
Switchable (OFF/HP/LP)
0 or 12dB @ 50Hz (Selectable)
20Hz to 20KHz +/-3 dB
>90dBA (20 to 20kHz)
50dB
<0.2% (Output-1W 4 Ohms)
150mV to 4V
>20K Ohms
10.2V to 15.5V DC
12dB/Oct, 30-250Hz Variable
Low Pass only
0 to 12dB @ 50Hz (Variable)
40Hz to 250Hz +/-3 dB
>70dBA (40 to 250Hz)
<0.2% (Output-1W 4 Ohms)
150mV to 4V
>20K Ohms
11V to 15.5V DC
12dB/Oct, 50-250Hz Variable
Low Pass
0 to 12dB @ 50Hz (Variable)
D3 400.2
2-Channel Amplifier
400 Watts RMS Output Power
(All Channels Driven):
(Into 4 Ohms)
(Into 2 Ohms)
(Bridged into 4 Ohms)
D3 500.4
4-Channel Amplifier
500 Watts RMS Output Power
(All Channels Driven):
(Into 4 Ohms)
(Into 2 Ohms)
(Bridged into 4 Ohms)
D3 600.1
Mono Amplifier
600 Watts RMS Output Power
(Single Channel Driven):
(Into 4 Ohms)
(Into 2 Ohms)
(Bridged into 1 Ohms)
D3 1000.1
Mono Amplifier
1000 Watts RMS Output Power
(Single Channel Driven):
(Into 4 Ohms)
(Into 2 Ohms)
(Bridged into 1 Ohms)
100w x 2
200w x 2
400w x 1
75w x 4
125w x 4
250w x 2
250w x 1
400w x 1
600w x 1
400w x 1
600w x 1
1000w x 1
3