Advertisement
Blood Pressure Monitor
Instruction Manual
GB Unit and LC-Display
1
(b)
1-2 cm
2
3
Proper use
•
This fully automatic electronic blood pressure monitor is intended for measuring the blood pressure at
home. It is a non-invasive blood pressure measurement system to measure the diastolic and systolic
blood pressure and pulse of an adult using a non-invasive technique by means of a cuff, which needs
to be fitted on the upper arm.
Contraindications
•
The device is not suitable for measuring the blood pressure of children. Ask your doctor before using it
on older children.
•
This blood pressure monitor is not suitable for persons with a strong arrhythmia.
Explanation of symbols
IMPORTANT
Follow the instructions for use!
Non-observance of these instructions
can result in serious injury or damage
to the device.
WARNING
These warning notes must be observed
to prevent any injury to the user.
CAUTION
These notes must be observed to prevent
any damage to the device.
NOTE
These notes give you useful additional
information on the installation or
operation.
Device classification: type BF applied part
Keep dry
LOT number
Manufacturer
Date of manufacture
- Please read carefully!
(a)
(c)
Scope of supply
Please check first of all that the unit is complete.
The following parts are included as standard:
• 1 ecomed blood pressure monitor BU-92E
• 1 cuff with air tube
• 4 batteries (type AA, LR6) 1.5 V
• 1 instruction manual
Please contact your supplier if you notice any
transport damage on unpacking the unit.
Common factors of wrong measurements
•
Please keep quiet for 5-10 minutes and avoid
eating, drinking alcohol, smoking, exercising and
bathing before taking a measurement. All these
factors will influence the measurement result.
•
Remove any garment that fits closely to your
upper arm.
•
Always measure on the same arm (normally left).
•
Measurements should be taken regularly at the
same time of each day, as the blood pressure
varies even during the day.
•
Any effort to support the arm during measurement
may increase the measured blood pressure.
•
Make sure, you are in a comfortable, relaxed
position and do not move or constrict your
muscles during measurement. Use a cushion to
support your arm if necessary.
•
If the arm artery lies lower or higher than the
heart, a false reading will be obtained.
•
A loose or open cuff causes false readings.
•
With repeated measurements, blood accu-
mulates in the arm which can lead to false
reading. Consecutive blood pressure measure-
ments should be repeated after 1 minute pause
or after the arm has been held up in order to
allow the accumulated blood to flow away.
BU-92E
4 x LR6,
1,5V, AA
Advertisement
Table of Contents
Related Manuals for Ecomed BU-92E
Summary of Contents for Ecomed BU-92E
- Page 1 Scope of supply Please check first of all that the unit is complete. The following parts are included as standard: • 1 ecomed blood pressure monitor BU-92E • 1 cuff with air tube • 4 batteries (type AA, LR6) 1.5 V •...
-
Page 2: Safety Instructions
How is blood pressure measured? The ecomed BU-92E is a blood pressure unit which is used to measure blood pressure at the upper arm. The measurement is carried out by a microprocessor, which, via a pressure sensor, measures the vibrations resulting from the inflation and deflation of the cuff over the artery. -
Page 3: Troubleshooting
WARNING Blood pressure that is too low represents just as great a health risk as blood pressure that is too high! Fits of dizziness may lead to dangerous situations arising (e.g. on stairs or in traffic)! Influencing and evaluating readings •... -
Page 4: Cleaning And Care
"Er 7" / "Er 8" / "Er A": Electronic-, parameter- or sensor error. Relax for 5 minutes and repeat the measurement. Important: Please contact your doctor if the error messages appear repeatedly. Keep still and do not move during the measurement. Cleaning and care Remove the batteries before cleaning the unit. -
Page 5: Technical Specifications
The following warranty terms apply: 1. The warranty period for ecomed products is two years from date of purchase. In case of a warranty claim, the date of purchase has to be proven by means of the sales receipt or invoice.
Need help?
Do you have a question about the BU-92E and is the answer not in the manual?
Questions and answers