Related Manuals for Abode ASCH6031B
Summary of Contents for Abode ASCH6031B
- Page 1 Cooker Hood Instruction Manual Model number(s): ASCH6031B / SS IMPORTANT: RETAIN FOR FUTURE REFERENCE...
-
Page 2: Table Of Contents
Contents Safety Instructions …………………… Product Overview …………………… Positioning …………………… Operating modes …………………… Installation …………………… 11-14 Usage …………………… Cleaning and Maintenance …………………… 16-22 Trouble shooting ……………………. Connection to the mains …………………… supply Guarantee …………………… Technical specification …………………… Notes ……………………... -
Page 3: Safety Instructions
Safety Instructions Important note: Please read this booklet before installing and switching on this appliance. The manufacturer assumes no responsibility for incorrect installation and usage as described in this booklet. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and... - Page 4 Safety Instructions • This appliance is not intended for operation with an external clock timer or a remote control. • Packaging material is dangerous to children. Never allow children to play with packaging material. • Risk of Death - Always ensure adequate fresh air in the room if the appliance is being operated in extraction-air mode at the same time as room air-dependent heat-producing appliance(s) are being operated.
- Page 5 Safety Instructions • In any case, consult your responsible Master Chimney Sweep. They will be able to assess the house's entire ventilation setup and will suggest the suitable ventilation measures to you. • Risk of Fire - Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months.
- Page 6 Safety Instructions • A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after- sales service. • Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after- sales technicians.
-
Page 7: Product Overview
Product overview 9 x wall 1 x hood fixing Plugs* bracket 2 x flue fixing 9 x large bracket screws 6 x small screws *Ensure wall fittings are suitable for the wall that is being installed on 1. Hood 6. Large Screws 2. -
Page 8: Positioning
Positioning • This appliance is installed on the wall. • Avoid damaging the product during installation • The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works correct when installed. •... -
Page 9: Top View
Positioning Top view 635-960 Side view Option Chimney 390 – 620 Front view All measurements in the diagram are in millimetres (mm) -
Page 10: Operating Modes
Operating modes This appliance can be used in exhaust-air mode or circulating air mode. Extraction-air mode The air which is drawn in is cleaned by the grease filters and extracted outside by a hose. Important Notes: • The extracted air must not be extracted into a functioning smoke, exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heat-producing appliances. -
Page 11: Installation
Installation Preparation Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made. See next page for diagram. 1. Ensure that that there is an electrical plug socket within adequate distance of the hood after it has been installed. 2. - Page 12 Installation Preparation Option Chimney 390 – 620 All measurements in the diagram are in millimetres (mm)
- Page 13 Installation Attaching and aligning the appliance. 1. Partially remove the protective film from the back of the appliance. 2. Hook the appliance on to the hood fixing bracket appliance (ensure the hood is fully hooked onto the hood fixing bracket, as the hooks on the bracket are stepped) and check that it is level with a spirit level 3.
- Page 14 Installation Attaching the flue duct Components inside the appliance may have sharp edges. Wear protective gloves. 1. Separate the flue ducts. 2. Remove the protective film from both flue ducts. 3. Place the hose on the duct outlet 4. Screw the upper flue duct to the sides of the flue fixing bracket using two small screws.
-
Page 15: Usage
Usage Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes. Control panel Icon Explanation Fan off Fan speed 1 (low) Fan speed 2 (medium) Fan speed 3 (high) - Page 16 Cleaning and Maintenance: Important notes: • The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning. • Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.
-
Page 17: Cleaning And Maintenance
Cleaning and Maintenance: Surface type How to clean Stainless Steel Hot soapy water: Clean with a dish cloth and dry with a soft cloth. Clean stainless steel surfaces in the direction of the grain only. Special stainless steel cleaning products are from specialist retailers. - Page 18 Cleaning and Maintenance: Aluminium grease filters: Removing and installing the Aluminium grease filters: Removing 1. Press the lock in and pull down the aluminium grease filter. 2. Take the filter out of the holder. 3. Clean the filter and allow to dry before replacing (refer to cleaning instructions on the following page).
- Page 19 Cleaning and Maintenance: Carbon filters (Included): Installing the Carbon grease filters: Remove the Aluminium filter(s) from the hood. You will now be able to access the motor, carefully attached the carbon filters to both ends of the motor. Carbon filters should be replaced after approximately 2-3 months of use.
- Page 20 Cleaning and Maintenance: Important notes • Grease deposits in the grease filter may catch fire. • Clean the grease filter at least every 2 months. • Never operate the appliance without the grease filter. • Do not use any aggressive, acidic or alkaline cleaning agents. •...
- Page 21 Cleaning and Maintenance: Replacing the light modules • You cannot replaced the light bulbs, the entire light module has to be replaced. • When changing the light modules, the contacts are live. • Before changing the light module(s), unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
- Page 22 Cleaning and Maintenance: 3. Remove the light from the its fitting in the front plate (this may require pressure or force to be applied). 4. Put the replacement light module into the fitting (ensuring the terminal is threaded through the fitting) and connect it to the terminal, and replace the protective casing.
-
Page 23: Trouble Shooting
Trouble Shooting: Problem Solution The plug is not plugged in. Connect the appliance to the electricity supply. Power cut Check whether other kitchen appliances are working. The appliance Faulty fuse does not work Check in the fuse box to make sure that the fuse for the appliance is working The fan is faulty. -
Page 24: Connection To The Mains
Connection to the mains supply WARNING- THIS APPLIANCE MUST BE EARTHED This appliance is designed to operate from a mains supply of AC220V-AC240V~50Hz. Check that the voltage marked on the product corresponds with your supply voltage. For UK use only – Plug fitting details (where applicable): As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The GREEN/YELLOW wire is the EARTH and must be connected to the terminal which... -
Page 25: Guarantee
Guarantee This product is guaranteed for 12 months from the date of the original purchase. If any defect arises due to faulty materials or workmanship you must contact Product Care with the original proof of purchase so a replacement or refund can be arranged. Refund or replacement is at the discretion of Product Care. -
Page 26: Technical Specification
Technical Specification Model number ASCH6031 SS/B Rated Voltage 220V – 240V ~ 50Hz Rated input 104W External Dimensions(HxWxD) 635-960 mm x 600mm x 500mm Extraction rate 470m³/h Light power 2 x 2W LED... -
Page 27: Notes
Notes... - Page 28 United Kingdom Product Care (Ireland) Ltd, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, T23 AT2P, Ireland. Abode is a registered trademark of Product Care Trading Limited. The ‘wheelie bin’ symbol is known as the 'Crossed-out wheelie bin Symbol'.
Need help?
Do you have a question about the ASCH6031B and is the answer not in the manual?
Questions and answers