Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ampete 88R
Summarization of Contents
Introduction to Ampete 88 Switching System
88S Shop Switcher
Description of the 88S switcher, a 2U unit connecting 8 amps and 8 cabinets, operated via remote control.
88S-STUDIO-2 Studio Switcher
Details on the 88S-STUDIO-2, a 2U switcher with 8 amps/8 cabs, front panel controls, and expandable system capabilities.
88R Remote Controller
Introduction to the 88R remote controller for the 88 Switching System, used to select amps/cabs via keypad and CAT5 connection.
88 Switching System Example Setups
Standard Shop Setup
Illustrates a standard shop setup for the Ampete 88 switching system, featuring multiple units and a remote.
Combined Shop Setup
Depicts a combined shop setup for the Ampete 88 system, integrating different models for enhanced functionality.
Studio Setup 1
Example of a studio setup using the 88S-STUDIO-2, showing a typical configuration.
Studio Setup 2
Second studio setup example for the 88S-STUDIO-2, showcasing an alternative arrangement.
Studio Setup 3
Third studio setup example for the 88S-STUDIO-2, presenting another possible configuration.
88S-STUDIO-2 Features
Features
Lists the key features of the 88S-STUDIO-2, including selectable amplifiers, speaker cabs, buffered inputs, and expandability.
88S-STUDIO-2 Front Panel Overview
Input - Buffered Instrument Input
Describes the buffered instrument input, its function, and recommendations for cascading units.
Amplifier Selection Switches (AMPS 1-8)
Details on how to select amplifiers using front panel switches, ensuring only one amp is active at a time.
Cabinet Selection Switches (CABS 1-8)
Explains cabinet selection, including impedance checks, and protection against running without a load.
Display Functionality
Information on the display showing unit IDs, amp/cab numbers, and error status indications.
88S-STUDIO-2 Rear Panel Connections
Remote or Previous Switcher Jack
RJ45 connector for data transmission with the 88R remote or another 88S/88S-STUDIO-2.
Following Switcher Jack
RJ45 connector for data transmission with the next higher ID 88S/88S-STUDIO-2.
Speaker Cabinets (1-8)
Connects speaker cabinets to the unit, advising to consider power handling and use speaker cables only.
SPK BUS / ATT.
Provides speaker output signal for cascading units and attenuator loop functionality.
Amplifier Speaker Outputs (1-8)
Connects amplifier outputs to the unit, with a maximum power limit of 300W per jack.
88S-STUDIO-2 Bus Connections
Line Bus
Carries instrument signal to all units in the system; can be used as unbuffered input for external preamps.
Amplifier Instrument Input
Connects amplifier instrument inputs, stressing the use of high-quality cables for sensitive connections.
System Hook-Up Diagram
88S-STUDIO-2 Unit 1
Diagram showing connections for the first 88S-STUDIO-2 unit, including cabinets and amplifier inputs/outputs.
88S-STUDIO-2 Unit 2
Diagram illustrating connections for the second 88S-STUDIO-2 unit, extending cabinet and amp connectivity.
88S-STUDIO-2 Unit 3
Diagram showing connections for the third 88S-STUDIO-2 unit, further expanding the system's capabilities.
88S-STUDIO-2 Unit n
General diagram for subsequent 88S-STUDIO-2 units in a cascaded system, detailing input/output connections.
Attenuator Loop Functionality
Attenuator Loop Setup
Explains how to use the attenuator loop for power soaks, including activation via the setup menu and bypass switching.
System Setup and Operation
Setup Menu Configuration
Guide to configuring unit ID and attenuator loop status through the setup menu on the 88S-STUDIO-2.
Using 88S-STUDIO-2 with 88R Remote
Details on using the 88S-STUDIO-2 standalone or with the 88R remote for amp and cab switching.
88R Remote Controller
88R Features
Overview of the 88R's features including numeric keypad, displays, CAT5 power, and footswitch/MIDI connectivity.
Using the 88R
Instructions on addressing amps and cabinets using the 88R keypad and confirming selections with ENTER buttons.
88R Operation and Error Handling
Error Messages
Explanation of common error messages like 'n.c.' (not connected) and 'no Cab' displayed on the 88R.
A/B and Footswitch Functionality
Describes the A/B function for toggling system states and its activation via keypad or footswitch.
ALL OFF Function
Details the ALL OFF key function, which unroutes all amplifiers and cabinets from the system.
MIDI Connectivity
Information on MIDI IN/THRU connectivity for switching commands using Program Change or Control Change messages.
88R Setup Menu and MIDI Control
Setup Menu Navigation
Guide to accessing and navigating the setup menu for MIDI channel and Control Change mode settings.
Control Change Modes
Explanation of Control Change modes 0 and 1, and the Control Change Table for mapping messages to functions.
Program Change (PC) Editing
Instructions on editing Program Changes to select Amp/Cab combinations and saving presets.
Troubleshooting Common Issues
No Signal When Amplifier is Chosen
Troubleshooting steps for when no signal is present after selecting an amplifier, checking connections.
No Amplifier or Cabinet Selection
Guidance on issues preventing amp or cabinet selection, checking for proper connections and prior selections.
Attenuator Behavior Issues
Troubleshooting tips for the attenuator behaving unexpectedly, checking if attenuator mode is activated.
Attenuator in Multi-Unit Systems
Advice on connecting an attenuator in a system with multiple 88S-STUDIO-2 units, disabling attenuator loop.
Product Specifications
88S-STUDIO-2 Dimensions and Power
Technical specifications for the 88S-STUDIO-2, including dimensions, weight, and maximum power consumption.
88R Dimensions and Weight
Technical specifications for the 88R remote, detailing its dimensions and weight.
Need help?
Do you have a question about the 88R and is the answer not in the manual?
Questions and answers