Advertisement
Quick Links
Advertisement
Related Manuals for ORTNER GO11-42/59
Summary of Contents for ORTNER GO11-42/59
- Page 1 Operating Manual...
- Page 3 Contents Introduction General and safety-related information Your storage stove data (type plate) Standards and limit values Fuels Control variants Commissioning Cleaning and maintenance Troubleshooting Warranty conditions Disposal...
- Page 4 The scent of the wood, the crackling of the logs, the view of the flames and the warmth on your skin. To ensure that your ORTNER storage stove will continue to be a reliable companion for many years, we kindly request that you carefully read this manual and follow the operating instructions.
- Page 5 Use the specified fuels in the ORTNER storage stove and do NOT use it as a waste incinerator. This can lead to the dama- ging of the storage stove (more on this on page 10).
- Page 6 Variable wood quantity The handling of highly combustible or explosive substances The maximum wood quantity of your storage stove may deviate (solid, liquid or gaseous) in the immediate vicinity is prohibited from the values specified on the type plate (partial load opera- during the operation of the storage stove.
- Page 7 Damage and reconstruction work on the storage stove Please contact your stove builder as soon as possible in the event of damage to the storage stove. The storage stove may only be continued to operate in consultation with your stove builder.
- Page 8 Your storage stove data (type plate) If the type plate is missing, please contact your specialist company. Another type plate is also located inside of your storage stove on the base plate below the combustion chamber floor.
- Page 9 A significant contribution to the environmentally friendly operation of the storage stove can only be ensured under adherence of all requirements specified in the operating manual. Your ORTNER storage stove has been verified in accordance with EN13229 and additionally complies with the following national emissions requirements:...
- Page 10 We generally recommend the use of dry, clean, untreated and as the ORTNER storage stoves, attention must be paid to the split hardwood with a maximum water content (in the core of correct fuel and correct handling. For this reason, we recom- the log) of 20 %.
- Page 11 Control variants Manual operation Automatic combustion control (ABS) The control of the combustion air is performed manually by the IWhen your storage stove is equipped with an automatic com- operator using the air adjustment lever. The inlet air register is bustion control, then this handles the control of the combus- open in the left setting of the air adjustment lever.
- Page 12 Remove all documents and accessory parts present in the combustion chamber before beginning the commissioning. With the exception of the variant with a lever handle, the ORTNER combustion chamber doors are always self-closing and self-locking. Operation of the combustion chamber door...
- Page 13 Stand to side of the glass panel. The integrated protection mechanism on the door of the ORTNER storage stove supports the safety in the event of the undesired opening of the door (child safety lock). With the correct leverage (green arrow), the closure mechanism is released very easily.
- Page 14 Finally, a handful of kindling is placed on top, which again on the correct should be stacked in an airy fashion. Now place an ORTNER heating. lighter under the kindling. Never use cardboard, paper, petrol, spirit or similar for this purpose.
- Page 15 Refilling When you operate your ORTNER storage stove in interval operation, then further refilling of fuel will only be necessary after the specified nominal heating time. When you want to enjoy the dancing of the flames for longer, then the specified maximum wood quantity can be split into two burns that follow each other immediately.
- Page 16 Check the sealing strips The combustion chamber lining serves for the protection of Only high-quality sealing strips are used on ORTNER storage the material located behind it as well as the air distribution. stoves, which are attuned to the requirements of the storage Due to the high thermal load, this material is subject to wear.
- Page 17 Professional cleaning and maintenance Have the cleaning of the chimney, the connection piece bet- ween the chimney and the storage stove and the ceramic heating gas flues performed regularly by a licensed specialist in accordance with the country-specific regulations. A blo- ckage of the chimney may occur as a result of a prolonged interruption of the heating operation.
- Page 18 Troubleshooting The draught of the storage stove is insufficient, the fire almost Condensate escapes from the connection piece between the goes out (Caution! Risk of deflagration): storage stove and the chimney and the chimney becomes wet and sooty: During a cold start or with low pressure weather, a reduced draught/no chimney draught can occur during the starting pha- Possible causes could be exhaust gas temperatures or chimney se, however, sufficient negative pressure is important for a se-...
- Page 19 The storage stove overheats: Possible causes of overheating could be too short intervals between reheating (heating interval too short), too much wood or the wrong heating material. Open the supply air damper and let the fire burn down. If your storage heater is equipped with a combustion control (ABS), switch off the power to the con- trol unit or briefly interrupt the door contact.
- Page 20 The basis for clean and proper heating is the correct fuel and fect was not reported during the warranty period. the correct handling of your ORTNER storage stove. When the recommendations cited by us are followed, then you will have The duration of the warranty is 100 months for:...
- Page 21 In accordance with the DIN 50320 standard withdrawn in 1997, wear indicates the progressive loss of material from the 3) The ORTNER storage stoves are fitted with an inner and surface of a solid body (main body), caused by mechanical outer glass ceramic pane.
- Page 22 Storage heating stove registration and warranty extension to exclude all visual impairments such as fine scratches, inclu- A handover report is included with each delivered ORTNER sions or small air bubbles. We must accept these as the cur- storage heating stove. This is completed by the stove fitter to- rent state of engineering, no claim for complaint results from gether with you and is returned to us.
- Page 23 Disposal Information on the dismantling, recycling and/or disposal at the end of the stove system’s service life General information › Beforehand, contact your local disposal company to inquire to which extent the building materials listed below can be dis- posed of separately and/or can be collected. ›...
- Page 24 ORTNER GmbH Hürmer Straße 36, A-3382 Loosdorf T +43 (0) 2754 / 2707 MADE IN AUSTRIA F +43 (0) 2754 / 2708 E office@ortner-cc.at www.ortner-cc.at As at 01/2024...
Need help?
Do you have a question about the GO11-42/59 and is the answer not in the manual?
Questions and answers