1. Manuals
  2. Brands
  3. Echo Manuals
  4. Brush Cutter
  5. SMR-2410 TYPE 1E - 02-99
  6. Operator's manual

Echo SMR-2410 TYPE 1E - 02-99 Operator's Manual

Grass trimmer/brush cutter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Grass Trimmer/Brush Cutter
Operator's Manual
MODELS,
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a
Safety Manual. Both must be read and understood for proper and safe operation.
X7502279506
Type 1E
SRM-2400
Serial Number 562682 & Up
SRM-2410
Serial Number 503485 & Up
WARNING
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
WARNING
DANGER
89869554136
02/99

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMR-2410 TYPE 1E - 02-99 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Echo SMR-2410 TYPE 1E - 02-99

Summary of Contents for Echo SMR-2410 TYPE 1E - 02-99

  • Page 1 WARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation. 89869554136 X7502279506 02/99...

  • Page 2: Table Of Contents

    NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the- job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.

  • Page 3: Manual Safety Symbols & Important Information

    RASS RIMMER RUSH UTTER PERATOR ANUAL & I ANUAL AFETY YMBOLS MPOR TANT NFORMATION Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

  • Page 4: Decals

    Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instruc- tions for specific information.

  • Page 5: Equipment

    RASS RIMMER RUSH UTTER PERATOR ANUAL EQUIPMENT Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.

  • Page 6: Personal Condition & Safety Equipment

    Brush Cutter handles. Gloves also reduce the transmission of machine vibration to your hands. Hearing Protection -- ECHO recommends wearing hearing protection whenever unit is used. Proper Clothing -- Wear snug fitting, durable clothing; - Pants should have long legs, shirts with long sleeves.

  • Page 7: Safe Operation

    RASS RIMMER RUSH UTTER PERATOR ANUAL SAFE OPERATION Determine Operation Area - Provide all operators of this equipment with the operator's manual and instructions for safe operation. (50 ft.) - Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions.

  • Page 8: Extended Operation/Extreme Conditions

    EXTENDED OPERATION EXTREME CONDITIONS Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers.

  • Page 9: Description

    The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.

  • Page 10: Emission Control

    EMISSION CONTROL IMPORTANT ENGINE INFORMATION ENGINE FAMILY: TEH0240824RC The emission control system for this engine is EM DISPLACEMENT: 23.6cc (Engine Modification). THIS ENGINE MEETS U.S. EPA PH1 AND 1995- 1999 CALIFORNIA EMISSION REGULATIONS FOR ULGE ENGINES. REFER TO OWNER'S MANUAL Emission Control Label located on Engine (EXAMPLE ONLY, information on label varies by FOR MAINTENANCE SPECIFICATIONS AND...
  • Page 11 25.SAFETY VIDEO - (Not included with unit) P/N 99922202540 English version only is available at a cost of $5.00 from ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete infor-...

  • Page 12: Specifications

    PECIFICATIONS M O D E L S R M - 2 4 0 0 1 E S R M - 2 4 1 0 1 E L e n g t h 1 5 0 0 m m ( 5 9 . 0 i n . ) 1 5 0 0 m m ( 5 9 .

  • Page 13: Assembly

    ECHO APPROVED OPTIONAL ATTACHMENTS WARNING DANGER • Use only ECHO approved attachments for these models. Serious injury may result from the use of non approved attachment combinations. Read and comply with all safety instructions listed in this manual and attachment manual.

  • Page 14: Blade Installation

    BLADE INSTALLATION All Models. IMPORTANT If non-standard monofilament head, METAL/PLASTIC blade or cultivator etc. is used, THE CARBURETOR MUST BE RE-SET or serious engine damage may occur. See "Carburetor Adjustment" pages 30 and "Specifica- tions" page 12 of this manual. WARNING DANGER You must install a U-Handle Kit and Blade Conversion kit before operating this unit using metal blades, otherwise...

  • Page 15: Harness Clamp Installation

    RASS RIMMER RUSH UTTER PERATOR ANUAL HARNESS CLAMP INSTALLATION NOTE Some models require installation of Harness Clamp. If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8 x 10mm Open End Wrench. Parts Required: Harness Clamp, 4 x 18mm Hexagon Head Bolt, Link, Spacer.

  • Page 16: Throttle Cable & Ignition Leads

    FRONT HANDLE INSTALLATION Tools Required: Screwdriver. Parts Required: None Position front handle for comfortable operation and secure with screws. HANDLE INSTALLATION Tools Required: 8mm x 10mm Open End Wrench, Slotted Screwdriver, 3mm and 4mm Hex Wrench, Scrench, Pliers. Parts Required: U-Handle Kit P/N 99944200521 NOTE On model 2410 use Steps 1, 10, 12, 13, 14B, 15, 17 and 18 only.
  • Page 17 / low idle extremes are adjusted properly. The throttle linkage must be adjusted by moving the adjustment fixture (E). Consult with your Echo Dealer for correct adjustment procedure. SRM-2400 14A. Connect jumper lead (M) spade terminal end to power head ignition lead (A).
  • Page 18 SRM-2410 14B. Connect ignition stop lead (A). Install ground lead with bolt (B). 15. Remove left side clutch case bolt (P). Install metal bracket clamp (Q) with curved end down. Install throttle linkage into bracket clamp and pinch tight with pliers. 16.

  • Page 19: Pre-Operation

    RASS RIMMER RUSH UTTER PERATOR ANUAL PERATION OPERATION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use WARNING DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can result in serious personal injury. Plastic and Nylon Blades Require "Blade Conversion Kit," P/N 99944200410 (metal shield [A] and shoulder harness [B]).
  • Page 20 8 Tooth Weed/Grass Blade (P/N 69600120331) is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/Clearing Blade (P/N 69500120330) is designed for cutting brush and woody growth up to 3"...

  • Page 21: Fuel

    Standard (ISO/CD 13738), must be used. Echo brand Premium 50:1 oil meets this standard. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD approved oil, such as Echo Premium 50:1 Two-stroke Oil, will void the two-stroke engine warranty.

  • Page 22: Equipment Check

    IMPORTANT S M T W T F Stored fuel ages. Do not mix more fuel than you expect to use in 4 5 6 thirty (30) days, ninety (90) days when a fuel stabilizer is added. 9 10 11 12 13 14 15 16 17 18 19 20 21 IMPORTANT 22 23 24 25 26 27 28...

  • Page 23: Operation

    DANGER The cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. Stop Switch - Start/Run. Move stop switch button (A) forward away from the STOPposition.

  • Page 24: Starting Warm Engine

    The cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. Stop Switch - Start/Run. Move Stop Switch button (A) forward away from the STOP position.

  • Page 25: Stopping Engine

    ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR- SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listsed, see your ECHO dealer for repairs.

  • Page 26: Maintenance Intervals

    MAINTENANCE INTERVALS i l y t I - t l i t l i i l o l f f ) s l l i o s t l t n i ® ® o i t n i f i r u o i t .

  • Page 27: Air Filter

    RASS RIMMER RUSH UTTER PERATOR ANUAL AIR FILTER Level 1. Tools required: Cleaning brush, 1" or 2" medium bristle paint brush. Parts required: 90030 REPOWER AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed.

  • Page 28: Spark Plug

    SPARK PLUG Level 2. Tools Required: Scrench (combination socket wrench & screw driver supplied with unit) Feeler gauge, preferably a wire gauge. Brush. Parts Required: Spark Plug, Champion RCJ-7Y or NGK BPMR-7Y 1. Remove spark plug and check for fouling, worn and rounded center electrode.

  • Page 29: Exhaust System

    RASS RIMMER RUSH UTTER PERATOR ANUAL NOTE The throttle linkage remains assembled to the cover and the spark plug lead and grommet remain installed. 3. Use the wooden stick or brush to remove dirt form cylinder fins. 4. Remove grass and leaves from the grid between the recoil starter and fuel tank.

  • Page 30: Carburetor Adjustment Emission

    CARBURETOR ADJUSTMENT Type 1E Emission Models Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compliance with EPA Phase 1 and California Emission Regula- tions.

  • Page 31: Nylon Line Replacement

    Level 1. Tools Required: Head locking tool (if head is to be removed) Parts Required: ECHO 0.095" Nylon Trimmer Line 40 feet (12m) long. 1. Hold drum (A) and turn spool (B) CW (clockwise) until it stops. Pull spool from drum. DO NOT push in on spool when turning.

  • Page 32: Sharpen Metal Blade

    SHARPENING METAL BLADES Three styles of metal blades are approved for use on the ECHO Brushcutter. The 8-tooth blade can be sharpened during normal maintenance. The clearing blade and 80 tooth blade require profes- sional service. Before sharpening, CLOSELY inspect blade for cracks (look at the bottom of each tooth and the center mounting hole closely), missing teeth and bending.

  • Page 33: Troubleshooting

    Engine Fuel at Fuel strainer clogged Clean No fuel at Cranks carburetor carburetor Fuel line clogged Clean See your Echo dealer Carburetor Carburetor See your Echo dealer No fuel at Fuel at cylinder cylinder Open choke Muffler wet Fuel mixture is too rich...

  • Page 34: Storage

    TORAGE Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1. Store unit in a dry, dust free place, out of the reach of children. WARNING DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.
  • Page 35 RASS RIMMER RUSH UTTER PERATOR ANUAL NOTES...

  • Page 36: Servicing Information

    Operator's Manual made payable to ECHO, INCORPORATED. State on a sheet of paper model number and serial number of the ECHO unit you have, part number of the manual (if known), your name and address and mail to address above.

This manual is also suitable for:

Srm-2400 type 1e - 02-99Smr-2410 1eSrm-2400 1e

Table of Contents