Related Manuals for Toshiba XP
Summarization of Contents
About This Manual
Purpose and Scope of Manual
Details the manual's scope and applicable motor typeforms.
Important Notices and Disclaimers
Warranty Information Overview
Outlines warranty terms and conditions, including the TIC Standard Warranty.
Activating Your Toshiba Warranty
Provides instructions for activating the warranty online.
General Safety Information
Safety Alert Symbol Explained
Explains the meaning and use of the safety alert symbol.
Understanding Signal Words
Defines signal words like DANGER, WARNING, CAUTION and their implications.
Special Hazard Symbols
Describes special hazard symbols used in the manual.
Equipment Warning Labels
Details warning labels attached to equipment and their importance.
Motor Installation Procedures
Installation Precautions
Lists safety precautions and requirements for motor installation.
Selecting Installation Location
Specifies suitable installation locations and environmental considerations.
Motor Unpacking Instructions
Provides instructions on how to properly unpack the motor.
Mounting the Motor Securely
Details procedures for securely mounting the motor onto a base.
Foundation Requirements
Anchor Bolt Installation
Describes the purpose and installation of anchor bolts.
Mounting Foundation and Bedplate
Bedplate Installation and Leveling
Details steps for installing and leveling the motor bedplate.
Motor Leveling and Coupling
Rigid Coupling Alignment
Discusses shaft alignment requirements for rigid couplings.
Shaft Alignment Techniques
Provides methods and tolerances for achieving proper shaft alignment.
Coupling Faces Alignment Check
Explains how to check coupling face separation for alignment.
Balancing Direct-Coupled Motors
Addresses potential imbalances after field assembly and how to correct them.
Flexible Coupling and Vibration
Vibration Causes and Solutions
Lists common causes of vibration and troubleshooting steps.
Motor Operation and Testing
Motor Start-Up Precheck
Lists essential checks before initial motor start-up.
Operation Precautions
Highlights precautions for operating motors, especially with ASDs.
Motor Precheck Procedures
Details specific pre-operation checks for the motor.
Motor Testing Guidelines
Outlines procedures for testing the motor under no-load and load conditions.
Motor Maintenance Procedures
Cleanliness Best Practices
Emphasizes the importance of cleanliness for motor performance and longevity.
Insulation Resistance Testing
Explains how to test and interpret insulation resistance.
Recommended Drying Practices
Describes methods for drying motor windings if insulation is compromised.
Motor Winding Drying Methods
Apply External Heat for Drying
Details the process of drying windings using external heat sources.
Apply Direct Current for Drying
Outlines an alternative method for drying windings using direct current.
Motor Lubrication Guidelines
Lubrication Specifications
Provides grease volumes and guidelines for relubrication.
Standard Service Lubrication
Defines service conditions and their impact on lubrication schedules.
Bearing Heating Issues
Overheating of Antifriction Bearings
Lists probable causes for bearing overheating and corrective actions.
Motor Disassembly and Reassembly
Remove/Replace Bearings
Provides guidelines for removing and replacing motor bearings.
Remove the Bearings
Details the procedure and tools for bearing removal.
Bearing Installation and Rotor Removal
Install the Bearings
Describes common bearing installation methods like pressing and induction heating.
Rotor Removal Process
Explains the process for safely removing the motor rotor.
Electrical Testing Procedures
Power Supply Requirements
Specifies voltage and frequency requirements for the power supply.
Motor Terminals and Connectivity
Guides on matching motor nameplate ratings and connection diagrams.
Field Insulation Test
Details procedures for testing motor insulation resistance.
Special Equipment and Accessories
Space Heaters in Motors
Describes the function and use of space heaters in motors.
Stator Temperature Detectors
Explains stator temperature detection methods.
Resistance Temperature Detectors (RTD)
Details how RTDs are used for temperature indication.
Thermocouple Usage
Describes thermocouples for ambient motor temperature measurement.
Bearing Temperature Detectors
Explains devices used to monitor bearing temperature.
Motor Air Filters
Discusses the role and types of air filters for motors.
Ordering Information and Spare Parts
Ordering Information
Guides on how to order motors and find catalog information.
Spare Parts Listing
Lists recommended spare parts based on motor quantity.
Need help?
Do you have a question about the XP and is the answer not in the manual?
Questions and answers