Related Manuals for AllSpark 24v 3000W
Summary of Contents for AllSpark 24v 3000W
- Page 1 AllSpark Pro-Series - Pure Sine Wave Inverters ® OPERATION & USER MANUAL Models: 12V 1000W 12V 2000W 12V 2500W 24V 3000W Revision 2 - Next review date 01.07.2025...
-
Page 2: Table Of Contents
WARNING: DANGER OF BATTERY DAMAGE OR EXPLOSION/FIRE ..................4 WARNING: MEDICAL OR LIFE PRESERVING DEVICES ....................... 4 WARNING - INSTALLATION PERSONNEL ..........................4 ® GETTING STARTED WITH YOUR ALLSPARK INVERTER ....................... 5 FRONT PANEL AND REAR PANEL REPRESENTATION ........................5 COMPONANT DESCRIPTIONS................................7 SIZING THE BATTERY .................................. -
Page 3: Welcome
Offroad Living is Owned and Operated by a True-Blue Aussie family based in Perth Western Australia with suppliers and installers throughout Australia. 2. WARNINGS, CAUTIONS AND NOTES It is critical that any operator or installer of this AllSpark ® Pro-Series Inverter, reads and follows all WARNINGS, CAUTIONS AND NOTES and all installation and operation instructions. -
Page 4: Warning: Danger Of Battery Damage Or Explosion/Fire
WARNING - INSTALLATION PERSONNEL This product produces high currents and voltages and should not be installed by untrained or inexperienced personnel. Offroad Living highly recommends that the installation of your new AllSpark ® Pro-Series Inverter is carried out by trained and certified electrical technicians. -
Page 5: Getting Started With Your Allspark ® Inverter
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ® 3. GETTING STARTED WITH YOUR ALLSPARK INVERTER When a motorized appliance or a tool turns on, there is almost always an initial surge of power to start up. This surge of power is referred to as the "starting load" or "peak load". Once started, the tool or appliance requires much less power to operate. - Page 6 __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ® AllSpark Pro-Series Pure Sine Wave User Manaual...
-
Page 7: Componant Descriptions
If you experience this, try using a larger battery or two batteries connected in parallel. All AllSpark ® LiFePO4 battery models can support a 2000w inverter. For higher wattage inverters we also have models available that are suitable to power 12v/2500w, 24v/3000w and 24v/4000w Inverters. -
Page 8: Installation
250A 24V 3000W 150A We recommend using AllSpark ® Manual Reset Circuit Breakers for inverter circuit protection. Ensure that the circuit breaker is in the open circuit position when connecting cables during installation. If using a circuit breaker is not suitable for your installation due to space constraints or other valid reasons, then a midi or mega fuse holder/fuse of the same current rating above should be used instead. -
Page 9: Sizing The Dc Supply Cables
24V 3000W 2B&S (35mm2) 0B&S (50mm2) *** Installations over 4m in length should be avoided *** If this is not possible, please contact Offroad Living for specialised technical advice before installation __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ® AllSpark Pro-Series Pure Sine Wave User Manaual... -
Page 10: Connecting The Inverter
(or positive busbar if applicable). If using a busbar, the full length of cable from battery terminal to inverter terminal must meet the minimum current ratings as per Section 4. __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ® AllSpark Pro-Series Pure Sine Wave User Manaual... -
Page 11: Installing The Remote Control Panel
® 6. Identify a path for the communications cable to run from the remote control panel to the front face of your new AllSpark Pro-series inverter. Protection the cable in appropriate ducting or sheathing and secure the cable to ensure it doesn’t move about unnecessarily. -
Page 12: Operation
The LCD display on the top cover will show the program code and then shows the input and output voltage. AllSpark® Pro-series Inverters have a soft starting function, turning ON power to your appliances after 3 seconds. -
Page 13: Specifications
DC Cable Size (B&S) 2-4m Physical Case High Quality Black Anodised Aluminium Dimensions (L x W x H mm) 280 x 160 x 90 395 x 220 x 92 47 x 220 x 92 __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ® AllSpark Pro-Series Pure Sine Wave User Manaual... -
Page 14: Troubleshooting
Driver error Contact after sales service – Discontinue Inverter Use SERVICE & TECHNICAL SUPPORT ® If you require technical assistance with the installation, operation or repair of your AllSpark Pro-Series Inverter, please contact: Offroad Living Unit 2, 29 Prestige Parade, Wangara WA 6065 Ph: 08 6205 6868 8. -
Page 15: The Legal Stuff
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Due to changes in product design and improvements over time, effective from the 1st of Sept 2022 AllSpark ® Pro-Series Inverters come with a 36-month return to base warranty. All models sold prior to this date have a 24-month warranty.
Need help?
Do you have a question about the 24v 3000W and is the answer not in the manual?
Questions and answers