Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Vanguard Manuals
  4. Relays
  5. 6560
  6. Product notice

Vanguard 6560 Product Notice

Applications ware
Hide thumbs

Advertisement

Quick Links

Download this manual
What's in This
Notice
In This Notice
Voice Applications The BRI Voice feature provides basic rate ISDN Voice support for Vanguard
This advisory notice describes the integration of Voice Relay, over an ISDN BRI
interface, in these Vanguard products:
• Vanguard 320
• Vanguard 6400 Series
• Vanguard 6520/6560
Topic
Applications ..................................................................................................
Hardware Installation ...................................................................................
Cabling .....................................................................................................
Configuration And Statistics ........................................................................
Configuration ...........................................................................................
ISDN BRI Interface Configuration ..........................................................
ISDN BRI Interface Statistics ..................................................................
products using the Voice Relay or Voice over IP features supported by Applications
Ware. This feature is enabled by a CSK; QSIG_OPTION.
Switched voice calls over the ISDN B-channels are controlled by D-channel
Common Channel Signaling messages. The BRI B-channel voice traffic is
compressed and packetized before transmission over either Frame Relay or IP. Voice
compression and packetization is performed between Vanguard nodes. The PCM
(Pulse Code Modulated) format is used between the Vanguard node and a PBX.
Vanguard Applications Ware
PRODUCT ADVISORY NOTICE
BRI Voice Feature for Release 5.3.23
Part No. T0143, Rev A
February 2002
Page 1 of 25
See Page
2
3
13
14
15
17
25

Advertisement

loading
Need help?

Need help?

Do you have a question about the 6560 and is the answer not in the manual?

Questions and answers

Related Manuals for Vanguard 6560

Summary of Contents for Vanguard 6560

  • Page 1 ISDN BRI Interface Configuration ............ISDN BRI Interface Statistics ..............Voice Applications The BRI Voice feature provides basic rate ISDN Voice support for Vanguard products using the Voice Relay or Voice over IP features supported by Applications Ware. This feature is enabled by a CSK; QSIG_OPTION.
  • Page 2 Applications for Voice Access via BRI Figure 1. Q.SIG Trunk Figure 1 shows a QSIG trunk between a PBX and a Vanguard product at each end of Between PBX and the network, for support of voice or fax calls. These trunks are point-to-point Vanguard connections supporting either negotiated or fixed TEI assignment.

  • Page 3: Hardware Installation

    Public Switched Telephone Network. The only application for this product is connection to a local PBX. NT Interface (RJ11 Connector) TE Interface ISA Carrier Card (RJ11 Connector) BRI Voice Daughtercard Figure 2. ISDN BRI Voice Daughtercard and Carrier Card for Vanguard 6520/6560...
  • Page 4 TE Interface (RJ-11 Connector) NT Interface (RJ-11 Connector) Interface Header Pins Figure 3. ISDN BRI Voice Daughtercard for Vanguard 320 and 6400 Series Products Warning! Before installing the card, read the following safety advice carefully: To Avoid any Harm to Yourself Before installing the card, power down the Vanguard.
  • Page 5 Vermeiden Sie in jedem Fall eine Berührung der Kontaktstifte am Rand der Karte oder an den integrierten Schaltkreisen. Der Widerstand der Kontaktstifte kann durch das natürliche Fett der Haut verändert werden. Vanguard 6520/ Perform these steps to install this daughtercard and carrier card into the Vanguard 6560 Installation 6520/6560. Step Action Verify that the power is OFF by removing the power cord.
  • Page 6 Part No. T0143, Rev A February 2002 Hardware Installation Page 6 of 25 Holding Screw Gently Insert Card Into Proper Slot Figure 4. Installing the BRI Voice Card in a Vanguard 6520/6560...
  • Page 7 Part No.T0143, Rev A February 2002 Hardware Installation Page 7 of 25 Vanguard 320 Perform these steps to install this daughtercard in a Vanguard 320. Installation Step Action Unplug the power cord from the primary power source and remove interface and power cables.
  • Page 8 Part No. T0143, Rev A February 2002 Hardware Installation Page 8 of 25 ISDN BRI Voice Feature Daughtercard Interface Header Pins Install in Port 1 Only Motherboard Interface Connector Figure 5. Vanguard 320 ISDN Daughtercard Installation...
  • Page 9 Hardware Installation Page 9 of 25 Vanguard 6430/ To install daughtercards in a Vanguard 6430 or 6450, you must first remove the 6450 Installation motherboard from this products enclosure, as shown in Figure 6. Perform these steps to install this daughtercard.
  • Page 10 Action (continued) Fasten the screw that attaches the daughtercard to the motherboard, then fasten the two rear panel coverplate screws. Daughtercard replacement/addition is complete. Reinstall the motherboard by reversing Steps 1 through 3. Captive Screw Figure 6. Vanguard 6430/6450 Installation...
  • Page 11 Part No.T0143, Rev A February 2002 Hardware Installation Page 11 of 25 Vanguard 6425 Figure 7, and this procedure, show how the Vanguard 6425 enclosure is opened to Installation allow access to the motherboard and install this daughtercard. Step Action Remove the two screws (one on each side) which secure the top cover to the base enclosure section.
  • Page 12 Part No. T0143, Rev A February 2002 Hardware Installation Page 12 of 25 Remove the two screws To install, reverse the procedure. from the cover as shown. Lift the cover from the 6425 chassis. Figure 7. Opening the Vanguard 6425 Enclosure...
  • Page 13 Part No.T0143, Rev A February 2002 Hardware Installation Page 13 of 25 Cabling Introduction The daughtercard is equipped with two RJ-11 connectors. One provides NT-side physical layer pinouts while the other provides TE-side physical layer pinouts (see Figures 1 and 2). Plug the cable into the appropriate physical interface connector, consistent with the interface configuration parameters for physical layer framing.
  • Page 14 Part No. T0143, Rev A February 2002 Configuration And Statistics Page 14 of 25 Configuration And Statistics Introduction This section describes the configuration and statistics related to the BRI Voice feature. Note SNMP is not currently supported by this release of Applications Ware.
  • Page 15 Configure an ISDN BRI Interface for each BRI Voice Daughtercard. Configuring X.25 Refer to the Vanguard ISDN and/or X.25 Basic Configuration manuals (Part Numbers T0103-06 and T0107 respectively) for specific instructions on this activity. These port numbers can be selected for the various products supported:...

  • Page 16: Configuration Menu

    Part No. T0143, Rev A February 2002 Configuration And Statistics Page 16 of 25 Accessing the BRI Complete this procedure to access the BRI ISDN Interface Configuration menu. ISDN Interface Configuration Menu Step Do This... Result Select Configure from the CTP The Configure menu is displayed.
  • Page 17 *D-Channel Port Number Range: • 0, 7, 13, 19, 25, 31, 37, 43, 49 for Vanguard 6560 • 13, 19, 25, 31, 37, 43, 49 for Vanguard 6520 • 7, 10, 13 for Vanguard 64xx products •...
  • Page 18 Part No. T0143, Rev A February 2002 Configuration And Statistics Page 18 of 25 Format Range: Data, Voice Default: Data Description: Specifies the format of the BRI Interface. • Data: The interface is used for inter-nodal traffic. • Voice: The interface is used for switched voice traffic to be compressed and packetized.
  • Page 19 Part No.T0143, Rev A February 2002 Configuration And Statistics Page 19 of 25 NT/TE Side Range: NT, TE Default: Description: Specifies the physical layer framing: • NT: Sets the physical layer interface framing to NT and forces internal or slave clocking to be selected. •...
  • Page 20 Part No. T0143, Rev A February 2002 Configuration And Statistics Page 20 of 25 *Clock Master Range: ENABLE, DISABLE Default: Disable Description: Provides clocking to the shared clock bus connecting all CCS interfaces. • ENABLE: Use this BRI interface to provide clocking to all slaves.
  • Page 21 Part No.T0143, Rev A February 2002 Configuration And Statistics Page 21 of 25 ISDN/QSIG Options Range: NONE, REPT, FORCE_PREF, FORCE_EXCL, BLOCK_SETUP_ACK, BLOCK_CALL_PROC, BLOCK_PROC_SETUP_ACK, BLOCKING_CALL_PROGRESS, BLOCK_ALERTING, BLOCK_SENDING_COMPLETE Default: NONE Description: Select ISDN/QSIG Debug Options • NONE: no ISDN options enabled • REPT: generates a 'MED' priority report for each change in the ISDN/QSIG signaling state machine •...
  • Page 22 Part No. T0143, Rev A February 2002 Configuration And Statistics Page 22 of 25 IEs to be Filtered (Outbound) Range: 0 to 30 alphanumeric characters, Default: (blank) Description: This parameter allows you to configure up to 5 non-standard IE's (Information Elements) to be filtered on any outbound ISDN/ QSIG message.
  • Page 23 Part No.T0143, Rev A February 2002 Configuration And Statistics Page 23 of 25 Calling/Called Party Number Plan Range: Unknown, ISDN, Telephony, Private Default: ISDN Description: This is the Calling/Called Party Number Plan as defined by ITU-T • Unknown: Unknown • ISDN: ISDN numbering plan (E.164) •...
  • Page 24 Part No. T0143, Rev A February 2002 Configuration And Statistics Page 24 of 25 (First) Local Subscriber Directory Number Range: Up to 16 characters. Default: (blank) Description Specifies the number used to replace the calling party address in SETUP messages associated with the first voice virtual port, according to the replacement rules specified by the “Calling Address Replacement”...
  • Page 25 The statistics available for ISDN BRI Voice Virtual ports are identical to those provided in the Vanguard Voice Relay Manual (Part Number T0104-03). Please refer to the Voice Port Statistics section in that manual for additional information.